Sketcher CarbonCopy/pl: Difference between revisions

From FreeCAD Documentation
(Created page with "{{Docnav/pl |Geometria zewnętrzna |Przełącz tryb konstrukcji |środowisko pracy Szkicownik |IconL=Sketcher_External.svg |IconR=Sketcher_ToggleConstruction.svg |IconC=Workbench_Sketcher.svg }}")
(Created page with "# Upewnij się, że jesteś w trybie edycji istniejącego {{Button|16px szkicu}}. Ten szkic jest celem operacji. # Naciśnij przycisk {{Button|16px '''Kalka techniczna'''}}. # Kliknij na krawędź z innego szkicu. Ten szkic jest źródłem operacji. # Elementy geometrii oraz ograniczenia są kopiowane do aktywnego szkicu. # Naciśnij {{KEY|Esc}} lub prawy przycisk myszki, aby zakończ...")
Line 30: Line 30:
==Użycie==
==Użycie==


# Make sure you are in the edit mode of an existing {{Button|[[File:Sketcher_NewSketch.svg|16px]] [[Sketcher_NewSketch|Sketch]]}}. This sketch is the target of the operation.
# Upewnij się, że jesteś w trybie edycji istniejącego {{Button|[[File:Sketcher_NewSketch.svg|16px]] [[Sketcher_NewSketch|szkicu]]}}. Ten szkic jest celem operacji.
# Press the {{Button|[[File:Sketcher CarbonCopy.svg|16px]] [[Sketcher_CarbonCopy|Carbon copy]]}} button.
# Naciśnij przycisk {{Button|[[File:Sketcher CarbonCopy.svg|16px]] '''Kalka techniczna'''}}.
# Kliknij na krawędź z innego szkicu. Ten szkic jest źródłem operacji.
# Click on an edge from another sketch. This sketch is the source of the operation.
# Elementy geometrii oraz ograniczenia są kopiowane do aktywnego szkicu.
# Geometry elements as well as constraints are copied into the active sketch.
# Press {{KEY|Esc}} or the right mouse button to terminate the operation.
# Naciśnij {{KEY|Esc}} lub prawy przycisk myszki, aby zakończyć działanie.


<span id="Notes"></span>
<span id="Notes"></span>

Revision as of 16:15, 9 April 2023

Sketcher CarbonCopy

Menu location
Szkic → Elementy geometryczne szkicownika → Kalka techniczna
Workbenches
Szkicownik
Default shortcut
G W
Introduced in version
0.17
See also
None


Opis

Narzędzie Kalka techniczna kopiuje całą geometrię i wiązania z innego szkicu do szkicu aktywnego.

Wiązania wymiarowe, które istnieją przed funkcją kopiowania, pozostają powiązane z wiązaniami wymiarowymi oryginalnego szkicu poprzez wyrażenia.

Użycie

  1. Upewnij się, że jesteś w trybie edycji istniejącego szkicu. Ten szkic jest celem operacji.
  2. Naciśnij przycisk Kalka techniczna.
  3. Kliknij na krawędź z innego szkicu. Ten szkic jest źródłem operacji.
  4. Elementy geometrii oraz ograniczenia są kopiowane do aktywnego szkicu.
  5. Naciśnij Esc lub prawy przycisk myszki, aby zakończyć działanie.

Uwagi

  • When sketches are used in the PartDesign Workbench, normally the sketch to carbon copy should be in the same PartDesign Body as the currently active sketch. If the sketch to be copied is not in the active Body, the mouse pointer will not allow selection. In this case, hold Ctrl to allow selection of sketches from other Bodies.
  • Normally, the sketch to select should be in a plane that is parallel to the currently active sketch. If the sketch to be copied is not parallel to the currently active sketch, hold Ctrl+Alt to allow selection of non-parallel sketches. The object will then be adjusted to the active sketch's plane. Noteː as of this writing this needs a save and reload of the document to make it visible. This works for sketches located outside of the currently active Body as well.
  • Since carbon-copied dimensional constraints use expressions they are rendered in a different color. The color can be customized with the Preferences Editor at Edit → Preferences → Sketcher → Colors → Expression dependent constraint color.
  • If the Sketcher mode has been changed to construction mode using Toggle construction geometry all copied geometry will be created in construction mode.

Ograniczenia

  • Kopiowany jest cały szkic, nie ma możliwości zaznaczenia tylko fragmentu. Po skopiowaniu można jednak usunąć niechciane elementy ze skopiowanego szkicu.