Part Extrude/pl: Difference between revisions

From FreeCAD Documentation
(Created page with "Drzewo modelu wyświetli tyle obiektów Wyciągnięcia, ile wybrano kształtów. Każdy kształt wejściowy jest umieszczony pod swoim obiektem Wyciągnięcie.")
(Created page with "==Parametry==")
Line 46: Line 46:
Drzewo modelu wyświetli tyle obiektów Wyciągnięcia, ile wybrano kształtów. Każdy kształt wejściowy jest umieszczony pod swoim obiektem Wyciągnięcie.
Drzewo modelu wyświetli tyle obiektów Wyciągnięcia, ile wybrano kształtów. Każdy kształt wejściowy jest umieszczony pod swoim obiektem Wyciągnięcie.


== Parameters ==
<span id="Parameters"></span>
==Parametry==


The Extrude shape is defined by the following parameters, which can be edited after its creation in the [[Property_editor|Property editor]].
The Extrude shape is defined by the following parameters, which can be edited after its creation in the [[Property_editor|Property editor]].

Revision as of 11:16, 24 June 2023

Część: Wyciągnięcie

Lokalizacja w menu
Część → Wyciągnięcie
Środowisko pracy
Część
Domyślny skrót
brak
Wprowadzono w wersji
-
Zobacz także
Przytnij, Wyciągnij

Opis

Wyciągnięcie części powoduje wydłużenie kształtu o określoną odległość i w określonym kierunku. Typ kształtu wyjściowego zależy od typu kształtu wejściowego i wybranych opcji.

W najczęstszych scenariuszach poniższa lista zawiera oczekiwany typ kształtu wyjściowego z danego typu kształtu wejściowego,

  • Wyciągnięcie wierzchołka (punktu) spowoduje utworzenie krawędzi liniowej (linii).
  • Wyciągnięcie otwartej krawędzi (np. linii, łuku), spowoduje utworzenie otwartej ściany (np. płaszczyzny)
  • Wyciągnięcie zamkniętej krawędzi (np. okręgu), opcjonalnie utworzy zamkniętą ścianę (np. otwarty walec) lub, jeśli parametr bryła ma wartość Prawda, utworzy bryłę (np. zamknięty, pełny walec).
  • Wyciągnięcie otwartej krzywej (np. krzywa środowiska Rysunek Roboczy), spowoduje utworzenie otwartej powłoki (kilka połączonych ścian).
  • wyciągnięcie zamkniętej krzywej (np. krzywa środowiska Rysunek Roboczy), opcjonalnie utworzy powłokę (kilka połączonych ścian) lub, jeśli parametr bryła ma wartość Prawda, utworzy bryłę
  • Wyciągnięcie ściany (np. płaszczyzny), spowoduje utworzenie bryły (np. prostopadłościanu).
  • Wyciągnięcie Kształt z tekstu, utworzy złożenie brył (ciąg jest złożeniem liter, z których każda jest bryłą)
  • Wyciągnięcie powłoki ze ścian, Prawda utworzy bryłę Złożoną.

Użycie

  1. Wybierz kształt(y) w oknie widoku 3D lub Widoku drzewa.
  2. Kliknij przycisk Wyciągnięcie ... na pasku narzędzi lub przejdź do menu Część → Wyciągnięcie ...
  3. Ustaw kierunek i długość oraz opcjonalnie inne parametry (więcej szczegółów znajduje się w sekcji Parametry).
  4. Kliknij OK.

Alternatywnie, wyboru można dokonać po uruchomieniu narzędzia, wybierając jeden lub więcej kształtów z listy w Panelu zadań.

Drzewo modelu wyświetli tyle obiektów Wyciągnięcia, ile wybrano kształtów. Każdy kształt wejściowy jest umieszczony pod swoim obiektem Wyciągnięcie.

Parametry

The Extrude shape is defined by the following parameters, which can be edited after its creation in the Property editor.

  • Base: the input shape (the shape upon which the Part Extrude was applied).
  • Dir: the direction to extend the shape. If Dir Mode is 'Custom', you can edit Dir. Otherwise, Dir is read-only, and computed from the linked shape.
  • Dir Link: parametric link to an edge (line) that sets the direction of extrusion.
  • Dir Mode: sets how Dir is controlled. 'Custom' means Dir is editable. 'Edge' means Dir is obtained from an edge (line) linked by Dir Link. 'Normal' means Dir is perpendicular to the plane of the input shape.
  • Length Fwd: The distance to extrude by. If both Length Fwd and Length Rev are zero, the length of Dir vector is used.
  • Length Rev: Additional length to extrude against Dir.
  • Solid: if True, extruding a closed edge or a closed wire will yield a solid. If False, a shell will result.
  • Reversed: reverses the extrusion to go against Dir.
  • Symmetric: if True, extrusion is centered at the input shape, and total length is Length Fwd. Length Rev is ignored.
  • Taper Angle and Taper Angle Rev: applies an angle to the extrusion, so that sides of the extrusion are drafted by the specified angle. Positive angle means the cross-section expands. Taper Angle Rev sets the taper for the reversed part of the extrusion (the part from Length Rev).
    introduced in version 0.20 Inner structures receive the opposite taper angle. This is done to facilitate the design of molds and molded parts.
    version 0.19 and below Tapered extrusion is only supported for shapes without inner structures. Taper does not work well if the shape contains B-splines.
  • Face Maker Class: sets C++ class name of face making code, which is used when making solids from wires. This property is here mainly for maintaining backward compatibility. Do not touch, unless you know what you are doing.
  • Placement: the standard placement parameters.
  • Label: label to be shown in the Model tree view (not available on Extrude creation).

Task dialog

  • OK button creates the extrusion, and closes the dialog.
  • Close button closes dialog, without doing anything.
  • Apply button creates the extrusion, but does not close the dialog. You can then select another shape in the list on the bottom, and create more extrusions. Clicking Apply may times creates many extrusions.
  • 'Direction' radio buttons: set the way extrusion direction is computed.
  • Select button: click it, and then pick an edge in 3D view. That edge will appear in text field next to the button, in format "ObjectName:EdgeN". You can also type the link manually. Values X,Y,Z will be filled according to the edge direction.
  • X, Y, Z buttons: Click x button to set extrusion direction to +x axis. Click it again to set -x axis.
  • X, Y, Z input fields: set or display the direction vector of extrusion. If both lengths are zero, the length of this vector sets the length of extrusion, and values are always in mm, regardless of unit preferences.
  • Length fields: set length of extrusion. These input fields have unit support.
  • Symmetric: spreads out the extrusion into both directions, so that the profile remains in the middle.
  • Taper Outward Angle: positive angle means profile is expanded at other end of extrusion.
  • Create Solid checkbox: if checked, extruding a closed wire or edge will yield a solid. It is checked by default, if a closed wire was preselected before invoking Part Extrude.
  • Shape list: here you select, what shapes to extrude. If multiple objects are selected, multiple Extrude objects are created.

Notes

  • The task dialog does not offer a preview, yet. Apply will create an extrusion object every time you click it, which can be useful as preview; however, they will remain and yet another one will be created as you click OK. Undo can be useful to clean them up before clicking OK.

Comparison with PartDesign Pad

PartDesign Pad is also an extrusion feature, but there are important differences:

  • Part Extrude always creates a standalone shape. PartDesign Pad fuses the extrusion result to the rest of the Body.
  • Part Extrude doesn't care where it is in model tree. PartDesign Pad can only live inside a PartDesign Body.
  • Part Extrude can extrude any object that has a Part geometry (OpenCASCADE shape), except for solids and CompSolids.
  • Part Extrude can extrude individual faces of other objects. PartDesign Pad will only accept either Sketch or faces of PartDesign objects as a profile.