PartDesign SubtractiveEllipsoid/pl: Difference between revisions

From FreeCAD Documentation
(Created page with "# Naciśnij przycisk {{Button|24px '''Subtraktywna elipsoida'''}}. '''Uwaga''': Subtraktywna elipsoida jest częścią menu narzędzi o nazwie '''Utwórz bryłę pierwotną do odjęcia'''. Po uruchomieniu programu FreeCAD, Subtraktywny prostopadłościan wyświetlany jest na pasku narzędzi domyślnie. Aby przejść do funkcji Elipsoia, kliknij strzałkę w dół na widocznej ikonce i wybierz z menu opcję Subtraktywna elipso...")
(Created page with "==Opcje==")
Line 36: Line 36:
# Pod aktywnym obiektem Zawartość pojawi się element Prostopadłościanu.
# Pod aktywnym obiektem Zawartość pojawi się element Prostopadłościanu.


==Options==
<span id="Options"></span>
==Opcje==


The Ellipsoid can be edited after its creation in two ways:
The Ellipsoid can be edited after its creation in two ways:

Revision as of 05:38, 18 June 2023

Projekt Części: Subtraktywna elipsoida

Lokalizacja w menu
Projekt Części → Utwórz cechę przez odjęcie → Subtraktywna elipsoida
Środowisko pracy
Projekt Części
Domyślny skrót
brak
Wprowadzono w wersji
0.17
Zobacz także
Komponent bryła pierwotna do odjęcia, Addytywna elipsoida

Opis

Funkcja ta wstawia pierwotną elipsoidę odejmowaną od aktywnej Zawartości. Jej kształt jest odejmowany od istniejącej bryły.

Po lewej: aktywna zawartość (A) pokazana w kolorze szarym i elipsoida do odjęcia (B) pokazana w kolorze czerwonym z przeźroczystością. Wynik po prawej.

Użycie

  1. Naciśnij przycisk Subtraktywna elipsoida. Uwaga: Subtraktywna elipsoida jest częścią menu narzędzi o nazwie Utwórz bryłę pierwotną do odjęcia. Po uruchomieniu programu FreeCAD, Subtraktywny prostopadłościan wyświetlany jest na pasku narzędzi domyślnie. Aby przejść do funkcji Elipsoia, kliknij strzałkę w dół na widocznej ikonce i wybierz z menu opcję Subtraktywna elipsoida.
  2. Ustaw parametry bryły i dołączenia.
  3. Kliknij OK.
  4. Pod aktywnym obiektem Zawartość pojawi się element Prostopadłościanu.

Opcje

The Ellipsoid can be edited after its creation in two ways:

  • Double-clicking it in the Model tree, or by right-clicking and selecting Edit primitive in the contextual menu; this brings up the Primitive parameters.
  • Via the Property editor.

Properties

  • DANEAttachment: defines the attachment mode as well as the Attachment Offset. See Part EditAttachment.
  • DANELabel: label given to the Ellipsoid object. Change to suit your needs.
  • DANERadius1: the radius value along the ellipsoid's vertical axis; by default, parallel to the Z-axis.
  • DANERadius2: the radius value along the ellipsoid's length; by default, parallel to the X-axis.
  • DANERadius3: the radius value along the ellipsoid's width; by default, parallel to the Y-axis. At the default value of zero, the ellipsoid forms an oblate spheroid.
  • DANEAngle1: (labelled V parameter in the Primitive parameters) lower truncation of the ellipsoid, parallel to the circular cross section (-90 degrees in a full spheroid)
  • DANEAngle2: (unlabelled in the Primitive parameters) upper truncation of the ellipsoid, parallel to the circular cross section (90 degrees in a full spheroid).
  • DANEAngle3: (labelled U parameter in the Primitive parameters) angle of rotation of the elliptical cross section (360 degrees in a full spheroid).