Projekt Części: Pochylenie ścian

From FreeCAD Documentation
Revision as of 06:14, 5 June 2022 by Kaktus (talk | contribs) (Created page with "==Właściwości==")

Projekt części: Pochylenie ścian

Lokalizacja w menu
Projekt Części → Zastosuj funkcje ulepszenia → Pochylenie ścian
Środowisko pracy
Projekt Części
Domyślny skrót
brak
Wprowadzono w wersji
-
Zobacz także
brak

Opis

Narzędzie Pochylenie ścian tworzy pochylenie kątowe wybranych ścian obiektu. Dodaje on do dokumentu obiekt Draft wraz z jego reprezentacją w oknie widoku drzewa.

Wybierz jedną lub więcej ścian na obiekcie przed uruchomieniem narzędzia. Tutaj zostały wybrane 2 ściany.
Wyświetlanie parametrów funkcji w Panelu zadań.
Dodano 2 ściany i zastosowano 10 stopniowe pochylenie. Dolna płaszczyzna pozostała wymiarowo niezmienna, podczas gdy pochylenie spowodowało zmniejszenie górnej płaszczyzny.
Płaszczyzna neutralna została zmieniona na górną. Teraz górna płaszczyzna pozostała stabilna wymiarowo, podczas gdy szkic powiększył dolną płaszczyznę..
Kierunek ścinania jest ustawiony na dolną prawą krawędź, co powoduje, że projekt jest ścinany w lewo..
Zaznaczenie pola wyboru Kierunek odwrotny spowodowało zastosowanie zanurzenia do wewnątrz zamiast na zewnątrz..

Użycie

Dodanie pochylenia ścian

  • Zaznacz jedną lub więcej ścian na obiekcie, a następnie uruchom narzędzie klikając jego ikonę lub wchodząc do menu.
  • W zakładce Parametry szkicu w Panelu zadań ustaw wymagane parametry i/lub opcje, jak opisano poniżej.
  • Kliknij przycisk OK, aby zatwierdzić.
  • Aby edytować projekt po zatwierdzeniu funkcji, kliknij dwukrotnie etykietę Pochylenie ścian w widoku drzewa lub kliknij prawym przyciskiem myszy i wybierz Edytuj pochylenie ścian.


Remember:
  • Since there must be at least one face for the feature, the last remaining face in the list cannot be removed.

Edit a draft

  1. Do one of the following:
    • Double-click the Draft item in the Tree view.
    • Right-click the Draft item in the Tree view and select Edit Draft from the context menu.
  2. The Draft parameters task panel opens. See Options for more information.
  3. Press the OK button to finish.

Opcje i parametry

  • Draft angle: Set the Draft angle either by entering a value or by clicking the up/down arrows.
  • Add: Add faces to the selection by pressing the Add button and selecting more faces.
  • Remove: Choose a way to remove faces from the selection:
    • Select one or more faces in the list and press the Del key or right-click the list and select Remove from the context menu.
    • Press the Remove button. All previously selected faces are highlighted in purple. Select each face to be removed.
  • Neutral plane: Set the the neutral plane by pressing the Neutral plane button and selecting the plane that must not change dimensionally.
  • Pull direction: Set the the pull direction by pressing the Pull direction button, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable.
  • Reverse pull direction: Invert the pull direction by checking the Reverse pull direction checkbox. This will toggle the draft between positive and negative angles.

Notes

Narzędzie Pochylenie ścian działa tylko na powierzchniach, które nie są styczne z innymi powierzchniami. Często popełnianym błędem jest próba zastosowania funkcji do powierzchni, na którą nałożono już zaokrąglenie. Aby rozwiązać ten problem, należy usunąć zaokrąglenie, zastosować pochylenie ścian, a następnie ponownie zastosować zaokrąglenie.

Właściwości

See also: Property editor.

A PartDesign Draft object is derived from a Part Feature object and inherits all its properties. It also has the following additional properties:

Data

Base

  • DANEAngle (Angle): Cannot be negative. Default: 1.5 °.
  • DANEReversed (Bool): Default: false.
  • DANEBase (LinkSub): Sub-link to the parent feature's list of selected edges and faces.
  • DANESupport Transform (Bool): "Include the base additive/subtractive shape when used in pattern features. If disabled, only the dressed part of the shape is used for patterning". Default: false.
  • DANE (hidden)Add Sub Shape (PartShape)
  • DANE (hidden)Base Feature (Link): Link to the parent feature.
  • DANE (hidden)_ Body (LinkHidden): Link to the parent body.

Draft

  • DANENeutral Plane (LinkSub): Sub-link to the parent feature's list containing the neutral plane.
  • DANEPull Direction (LinkSub)

Part Design

  • DANERefine (Bool): "Refine shape (clean up redundant edges) after adding/subtracting". The default value is determined by the Automatically refine model after sketch-based operation preference. See PartDesign Preferences.