FEM Workbench/ja: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 52: Line 52:
* [[Image:FEM_MaterialMechanicalNonlinear.svg|32px]] [[FEM_MaterialMechanicalNonlinear|Nonlinear mechanical material]]: Lets you select a material from the database.
* [[Image:FEM_MaterialMechanicalNonlinear.svg|32px]] [[FEM_MaterialMechanicalNonlinear|Nonlinear mechanical material]]: Lets you select a material from the database.


* [[Image:FEM_MaterialReinforced.svg|32px]] [[FEM_MaterialReinforced|Reinforced material]]: Lets you select reinforced materials consist of a matrix and a reinforcement from the database.
* [[Image:FEM_MaterialReinforced.svg|32px]] [[FEM_MaterialReinforced|Reinforced material (concrete)]]: Lets you select reinforced materials consist of a matrix and a reinforcement from the database.


* [[Image:Arch_Material_Group.svg|32px]] [[Material_editor|Material editor]]:: Lets you open the material editor to edit materials.
* [[Image:Arch_Material_Group.svg|32px]] [[Material_editor|Material editor]]: Lets you open the material editor to edit materials.


===要素の幾何学===
===要素の幾何学===
Line 70: Line 70:
* [[Image:FEM_ConstraintElectrostaticPotential.svg|32px]] [[FEM_ConstraintElectrostaticPotential|Constraint electrostatic potential]]:
* [[Image:FEM_ConstraintElectrostaticPotential.svg|32px]] [[FEM_ConstraintElectrostaticPotential|Constraint electrostatic potential]]:


<div class="mw-translate-fuzzy">
===流体の制約===
===流体の制約===
</div>


* [[Image:FEM_ConstraintInitialFlowVelocity.svg|32px]] [[FEM_ConstraintInitialFlowVelocity|Constraint initial flow velocity]]: Used to define an initial flow velocity for the domain.
* [[Image:FEM_ConstraintInitialFlowVelocity.svg|32px]] [[FEM_ConstraintInitialFlowVelocity|Constraint initial flow velocity]]: Used to define an initial flow velocity for the domain.

* [[Image:FEM_ConstraintFluidBoundary.svg|32px]] [[FEM_ConstraintFluidBoundary|Constraint fluid boundary]]:


* [[Image:FEM_ConstraintFlowVelocity.svg|32px]] [[FEM_ConstraintFlowVelocity|Constraint flow velocity]]: Used to define a flow velocity as a boundary condition at an edge (2D) or face (3D).
* [[Image:FEM_ConstraintFlowVelocity.svg|32px]] [[FEM_ConstraintFlowVelocity|Constraint flow velocity]]: Used to define a flow velocity as a boundary condition at an edge (2D) or face (3D).


=== Geometrical Constraints ===

* [[Image:FEM_ConstraintPlaneRotation.svg|32px]] [[FEM_ConstraintPlaneRotation|Constraint plane rotation]]: Used to define a plane rotation constraint on a planar face.

* [[Image:FEM_ConstraintSectionPrint.svg|32px]] [[FEM_ConstraintSectionPrint|Constraint section print]]: {{Version|0.19}}

* [[Image:FEM_ConstraintTransform.svg|32px]] [[FEM_ConstraintTransform|Constraint transform]]: Used to define a transform constraint on a face.

<div class="mw-translate-fuzzy">
===機械的な制約===
===機械的な制約===
</div>


* [[Image:FEM_ConstraintFixed.svg|32px]] [[FEM_ConstraintFixed|Constraint fixed]]: Used to define a fixed constraint on point/edge/face(s).
* [[Image:FEM_ConstraintFixed.svg|32px]] [[FEM_ConstraintFixed|Constraint fixed]]: Used to define a fixed constraint on point/edge/face(s).


* [[Image:FEM_ConstraintDisplacement.svg|32px]] [[FEM_ConstraintDisplacement|Constraint displacement]]: Used to define a displacement constraint on point/edge/face(s).
* [[Image:FEM_ConstraintDisplacement.svg|32px]] [[FEM_ConstraintDisplacement|Constraint displacement]]: Used to define a displacement constraint on point/edge/face(s).

* [[Image:FEM_ConstraintPlaneRotation.svg|32px]] [[FEM_ConstraintPlaneRotation|Constraint plane rotation]]: Used to define a plane rotation constraint on a planar face.


* [[Image:FEM_ConstraintContact.svg|32px]] [[FEM_ConstraintContact|Constraint contact]]: Used to define a contact constraint between two faces.
* [[Image:FEM_ConstraintContact.svg|32px]] [[FEM_ConstraintContact|Constraint contact]]: Used to define a contact constraint between two faces.


* [[Image:FEM_ConstraintTransform.svg|32px]] [[FEM_ConstraintTransform|Constraint transform]]: Used to define a transform constraint on a face.
* [[Image:FEM_ConstraintTie.svg|32px]] [[FEM_ConstraintTie|Constraint tie]]: {{Version|0.19}}


* [[Image:FEM_ConstraintForce.svg|32px]] [[FEM_ConstraintForce|Constraint force]]: Used to define a force in [N] applied uniformly to a selectable face in a definable direction.
* [[Image:FEM_ConstraintForce.svg|32px]] [[FEM_ConstraintForce|Constraint force]]: Used to define a force in [N] applied uniformly to a selectable face in a definable direction.
Line 96: Line 104:
* [[Image:FEM_ConstraintSelfWeight.svg|32px]] [[FEM_ConstraintSelfWeight|Constraint self weight]]: Used to define a gravity acceleration acting on a model.
* [[Image:FEM_ConstraintSelfWeight.svg|32px]] [[FEM_ConstraintSelfWeight|Constraint self weight]]: Used to define a gravity acceleration acting on a model.


<div class="mw-translate-fuzzy">
* [[Image:FEM_ConstraintBearing.svg|32px]] [[FEM_ConstraintBearing|Constraint bearing]]: Used to define a bearing constraint.

* [[Image:FEM_ConstraintGear.svg|32px]] [[FEM_ConstraintGear|Constraint gear]]: Used to define a gear constraint.

* [[Image:FEM_ConstraintPulley.svg|32px]] [[FEM_ConstraintPulley|Constraint pulley]]: Used to define a pulley constraint.

===熱的制約===
===熱的制約===
</div>


* [[Image:FEM_ConstraintInitialTemperature.svg|32px]] [[FEM_ConstraintInitialTemperature|Constraint initial temperature]]: Used to define the initial temperature of a body.
* [[Image:FEM_ConstraintInitialTemperature.svg|32px]] [[FEM_ConstraintInitialTemperature|Constraint initial temperature]]: Used to define the initial temperature of a body.
Line 111: Line 115:


* [[Image:FEM_ConstraintBodyHeatSource.svg|32px]] [[FEM_ConstraintBodyHeatSource|Constraint body heat source]]:
* [[Image:FEM_ConstraintBodyHeatSource.svg|32px]] [[FEM_ConstraintBodyHeatSource|Constraint body heat source]]:

=== Constraints without solver ===

* [[Image:FEM_ConstraintFluidBoundary.svg|32px]] [[FEM_ConstraintFluidBoundary|Fluid boundary condition]]:

* [[Image:FEM_ConstraintBearing.svg|32px]] [[FEM_ConstraintBearing|Constraint bearing]]: Used to define a bearing constraint.

* [[Image:FEM_ConstraintGear.svg|32px]] [[FEM_ConstraintGear|Constraint gear]]: Used to define a gear constraint.

* [[Image:FEM_ConstraintPulley.svg|32px]] [[FEM_ConstraintPulley|Constraint pulley]]: Used to define a pulley constraint.

=== Overwrite Constants ===

* [[Image:FEM_ConstantVacuumPermittivity.svg|32px]] [[FEM_ConstantVacuumPermittivity|Constant vacuum permittivity]]: {{Version|0.19}}


==メニュー:メッシュ==
==メニュー:メッシュ==
Line 116: Line 134:
* [[Image:FEM_MeshNetgenFromShape.svg|32px]] [[FEM_MeshNetgenFromShape|FEM mesh from shape by Netgen]]:
* [[Image:FEM_MeshNetgenFromShape.svg|32px]] [[FEM_MeshNetgenFromShape|FEM mesh from shape by Netgen]]:


* [[Image:FEM_MeshGmshFromShape.svg|32px]] [[FEM_MeshGmshFromShape|FEM mesh from shape by GMSH]]:
* [[Image:FEM_MeshGmshFromShape.svg|32px]] [[FEM_MeshGmshFromShape|FEM mesh from shape by Gmsh]]:


* [[Image:FEM_MeshBoundaryLayer.svg|32px]] [[FEM_MeshBoundaryLayer|FEM mesh boundary layer]]:
* [[Image:FEM_MeshBoundaryLayer.svg|32px]] [[FEM_MeshBoundaryLayer|FEM mesh boundary layer]]:
Line 130: Line 148:
==メニュー:Solve==
==メニュー:Solve==


* [[Image:FEM_SolverCalculixCxxtools.svg|32px]] [[FEM_SolverCalculixCxxtools|Solver Calculix CCX tools]]: Creates a new solver for this analysis. In most cases the solver is created together with the analysis.
* [[Image:FEM_SolverCalculixCxxtools.svg|32px]] [[FEM_SolverCalculixCxxtools|Solver CalculiX Standard]]: Creates a new solver for this analysis. In most cases the solver is created together with the analysis.


* [[Image:FEM_SolverCalculiX.svg|32px]] [[FEM_SolverCalculiX|Solver CalculiX]]:
* [[Image:FEM_SolverCalculiX.svg|32px]] [[FEM_SolverCalculiX|Solver CalculiX (experimental)]]:


* [[Image:FEM_SolverElmer.svg|32px]] [[FEM_SolverElmer|Solver Elmer]]: Creates the solver controller for Elmer. It is independent from other solver objects.
* [[Image:FEM_SolverElmer.svg|32px]] [[FEM_SolverElmer|Solver Elmer]]: Creates the solver controller for Elmer. It is independent from other solver objects.
Line 138: Line 156:
* [[Image:FEM_SolverZ88.svg|32px]] [[FEM_SolverZ88|Solver Z88]]:
* [[Image:FEM_SolverZ88.svg|32px]] [[FEM_SolverZ88|Solver Z88]]:


* [[Image:FEM_EquationHeat.svg|32px]] [[FEM_EquationHeat|Equation heat]]:
* [[Image:FEM_EquationElasticity.svg|32px]] [[FEM_EquationElasticity|Elasticity equation]]:

* [[Image:FEM_EquationElectricforce.svg|32px]] [[FEM_EquationElectricforce|Electricforce equation]]: {{Version|0.19}}


* [[Image:FEM_EquationElasticity.svg|32px]] [[FEM_EquationElasticity|Equation elasticity]]:
* [[Image:FEM_EquationElectrostatic.svg|32px]] [[FEM_EquationElectrostatic|Electrostatic equation]]:


* [[Image:FEM_EquationElectrostatic.svg|32px]] [[FEM_EquationElectrostatic|Equation electrostatic]]:
* [[Image:FEM_EquationFlow.svg|32px]] [[FEM_EquationFlow|Flow equation]]:


* [[Image:FEM_EquationFlux.svg|32px]] [[FEM_EquationFlux|Equation flux]]:
* [[Image:FEM_EquationFlux.svg|32px]] [[FEM_EquationFlux|Flux equation]]:


* [[Image:FEM_EquationFlow.svg|32px]] [[FEM_EquationFlow|Equation flow]]:
* [[Image:FEM_EquationHeat.svg|32px]] [[FEM_EquationHeat|Heat equation]]:


* [[Image:FEM_SolverControl.svg|32px]] [[FEM_SolverControl|Solver job control]]: Opens the menu to adjust and start the selected solver.
* [[Image:FEM_SolverControl.svg|32px]] [[FEM_SolverControl|Solver job control]]: Opens the menu to adjust and start the selected solver.


* [[Image:FEM_SolverRun.svg|32px]] [[FEM_SolverRun|Solver run calculation]]: Runs the selected solver of the active analysis.
* [[Image:FEM_SolverRun.svg|32px]] [[FEM_SolverRun|Run solver calculations]]: Runs the selected solver of the active analysis.


==メニュー:結果==
==メニュー:結果==


* [[Image:FEM_ResultsPurge.svg|32px]] [[FEM_ResultsPurge|Results purge]]: Deletes the results of the active analysis.
* [[Image:FEM_ResultsPurge.svg|32px]] [[FEM_ResultsPurge|Purge results]]: Deletes the results of the active analysis.


* [[Image:FEM_ResultShow.svg|24px]] [[FEM_ResultShow|Result show]]: Used to display the result of an analysis.
* [[Image:FEM_ResultShow.svg|24px]] [[FEM_ResultShow|Show result]]: Used to display the result of an analysis.


* [[Image:FEM_PostApplyChanges.svg|32px]] [[FEM_PostApplyChanges|Post Apply changes]]:
* [[Image:FEM_PostApplyChanges.svg|32px]] [[FEM_PostApplyChanges|Apply changes to pipeline]]:


* [[Image:FEM_PostPipelineFromResult.svg|32px]] [[FEM_PostPipelineFromResult|Post Pipeline from result]]:
* [[Image:FEM_PostPipelineFromResult.svg|32px]] [[FEM_PostPipelineFromResult|Post pipeline from result]]:


* [[Image:FEM_PostFilterWarp.svg|32px]] [[FEM_PostFilterWarp|Post Create warp vector filter]]:
* [[Image:FEM_PostFilterWarp.svg|32px]] [[FEM_PostFilterWarp|Warp filter]]:


* [[Image:FEM_PostFilterClipScalar.svg|32px]] [[FEM_PostFilterClipScalar|Post Create scalar clip filter]]:
* [[Image:FEM_PostFilterClipScalar.svg|32px]] [[FEM_PostFilterClipScalar|Scalar clip filter]]:


* [[Image:FEM_PostFilterCutFunction.svg|32px]] [[FEM_PostFilterCutFunction|Post Create cut filter]]:
* [[Image:FEM_PostFilterCutFunction.svg|32px]] [[FEM_PostFilterCutFunction|Function cut filter]]:


* [[Image:FEM_PostFilterClipRegion.svg|32px]] [[FEM_PostFilterClipRegion|Post Create clip filter]]:
* [[Image:FEM_PostFilterClipRegion.svg|32px]] [[FEM_PostFilterClipRegion|Region clip filter]]:


* [[Image:FEM_PostFilterDataAlongLine.svg|32px]] [[FEM_PostFilterDataAlongLine|Post Create data along line filter]]:
* [[Image:FEM_PostFilterDataAlongLine.svg|32px]] [[FEM_PostFilterDataAlongLine|Line clip filter]]:


* [[Image:FEM_PostFilterLinearizedStresses.svg|32px]] [[FEM_PostFilterLinearizedStresses|Post Create linearized stresses]]:
* [[Image:FEM_PostFilterLinearizedStresses.svg|32px]] [[FEM_PostFilterLinearizedStresses|Stress linearization plot]]:


* [[Image:FEM_PostFilterDataAtPoint.svg|32px]] [[FEM_PostFilterDataAtPoint|Post Create data at point filter]]:
* [[Image:FEM_PostFilterDataAtPoint.svg|32px]] [[FEM_PostFilterDataAtPoint|Data at point clip filter]]:


* [[Image:Fem-post-geo-sphere.svg|32px]][[File:Toolbar_flyout_arrow.svg|16px]] [[FEM_PostCreateFunctions|Post Create functions]]:
* [[FEM_PostCreateFunctions|Filter functions]]:
** [[Image:Fem-post-geo-sphere.svg|32px]] :
** [[Image:Fem-post-geo-plane.svg|32px]]
** [[Image:Fem-post-geo-plane.svg|32px]] :
** [[Image:Fem-post-geo-sphere.svg|32px]]


==メニュー:ユーティリティ==
==メニュー:ユーティリティ==
Line 186: Line 206:
* [[Image:FEM_ClippingPlaneRemoveAll.svg|32px]] [[FEM_ClippingPlaneRemoveAll|Remove all clipping planes]]:
* [[Image:FEM_ClippingPlaneRemoveAll.svg|32px]] [[FEM_ClippingPlaneRemoveAll|Remove all clipping planes]]:


* [[Image:FEM_Examples.svg|32px]] [[FEM_Examples|FEM Examples]]: Open the GUI to access FEM examples.
* [[Image:FEM_Examples.svg|32px]] [[FEM_Examples|Open FEM examples]]: Open the GUI to access FEM examples.


==コンテキストメニュー==
==コンテキストメニュー==


* [[Image:FEM_MeshClear.svg|32px]] [[FEM_MeshClear|FEM mesh clear]]:
* [[Image:FEM_MeshClear.svg|32px]] [[FEM_MeshClear|Clear FEM mesh]]:


* [[Image:FEM_MeshDisplayInfo.svg|32px]] [[FEM_MeshDisplayInfo|FEM mesh display info]]:
* [[Image:FEM_MeshDisplayInfo.svg|32px]] [[FEM_MeshDisplayInfo|Display FEM mesh info]]:


==環境設定==
==環境設定==

Revision as of 15:50, 25 February 2021

FEM workbench icon

はじめに

FEM Workbenchは、FreeCAD用の最新の有限要素解析(FEA)ワークフローを提供します。 主にこれは、分析を行うすべてのツールが1つのグラフィカルユーザーインターフェイス(GUI)に統合されていることを意味します。

ワークフロー

有限要素解析を実行する手順は次のとおりです。 #前処理:分析問題を設定する。

    1. ジオメトリのモデリング:FreeCADでジオメトリを作成するか、別のアプリケーションからジオメトリをインポートします。
    2. 分析を作成する。
      1. 幾何モデルのための有限要素メッシュの作成。
      2. 荷重や固定されたサポートなどの制約をモデルに追加する。
      3. 解析モデルに材料を追加する。

#Solving:FreeCAD内の外部ソルバーを使用して方程式系を解く。 #Postprocessing:FreeCAD内の解析結果を視覚化します。

FreeCAD 0.15以降、FEM WorkbenchはWindows、MacOSX、Linuxプラットフォームで使用できます。 ワークベンチは外部ソルバーを使用するため、手動セットアップの量は使用しているオペレーティングシステムによって異なります。 外部ツールの設定方法については、 FEM Installページを参照してください。

Workflow of the FEM Workbench; the workbench calls two external programs to perform meshing of a solid object, and perform the actual solution of the finite element problem

メニュー:モデル

  • Analysis container: Creates a new container for a mechanical analysis. If a solid is selected in the tree view before clicking on it, the meshing dialog will be opened next.

材料

要素の幾何学

Electrostatic Constraints

流体の制約

Geometrical Constraints

機械的な制約

  • Constraint force: Used to define a force in [N] applied uniformly to a selectable face in a definable direction.

熱的制約

Constraints without solver

Overwrite Constants

メニュー:メッシュ

  • Nodes set: Creates/defines a node set from FEM mesh.

メニュー:Solve

  • Solver CalculiX Standard: Creates a new solver for this analysis. In most cases the solver is created together with the analysis.
  • Solver Elmer: Creates the solver controller for Elmer. It is independent from other solver objects.

メニュー:結果

  • Show result: Used to display the result of an analysis.

メニュー:ユーティリティ

コンテキストメニュー

環境設定

リンク

FEMインストールをクリックすると、動作中のFEMモジュールを設定する方法の詳細が表示されます。

The following pages explain different topics of the FEM Workbench.

FEM Install: a detailed description on how to set up the external programs used in the workbench.

FEM Mesh: further information on obtaining a mesh for finite element analysis.

FEM Solver: further information on the different solvers available in the workbench, and those that could be used in the future.

FEM CalculiX: further information on CalculiX, the default solver used in the workbench for structural analysis.

FEM Concrete: interesting information on the topic of simulating concrete structures.

FEM Project: further information on the unit system, limitations, and the development ideas and roadmap of the workbench.

チュートリアル

チュートリアル1 FEM CalculiXカンチレバー3D

Tutorial 2: FEM Tutorial; simple tension analysis of a structure.

Tutorial 3: FEM Tutorial Python; set up the cantilever example entirely through scripting in Python, including the mesh.

Tutorial 4: FEM Shear of a Composite Block; see the deformation of a block that is comprised of two materials.

Tutorial 5: Transient FEM analysis

Tutorial 6: Post-Processing_of_FEM_Results_with_Paraview

Tutorial 7: FEM Example Capacitance Two Balls; Elmer's GUI tutorial 6 "Electrostatics Capacitance Two Balls" using FEM Examples.


Coupled thermal mechanical analysis tutorials by openSIM

Video tutorial 1: FEM video for beginner (including YouTube link)

Video tutorial 2: FEM video for beginner (including YouTube link)

Many video tutorials: anisim Open Source Engineering Software (in German)

Extending the FEM Workbench

The FEM Workbench is under constant development. An objective of the project is to find ways to easily interact with various FEM solvers, so that the end user can streamline the process of creating, meshing, simulating, and optimizing an engineering design problem, all within FreeCAD.

The following information is aimed at power users and developers who want to extend the FEM Workbench in different ways. Familiarity with C++ and Python is expected, and also some knowledge of the "document object" system used in FreeCAD is necessary; this information is available in the Power users hub and the Developer hub. Please notice that since FreeCAD is under active development, some articles may be too old, and thus obsolete. The most up to date information is discussed in the FreeCAD forums, in the Development section. For FEM discussions, advice or assistance in extending the workbench, the reader should refer to the FEM subforum.

The following articles explain how the workbench can be extended, for example, by adding new types of boundary conditions (constraints), or equations.

A developer's guide has been written to help power users in understanding the complex FreeCAD codebase and the interactions between the core elements and the individual workbenches. The book is hosted at github so multiple users can contribute to it and keep it updated.