Draft Vieleck
Draft Vieleck |
Menüeintrag |
---|
Entwurf → Vieleck |
Arbeitsbereich |
Draft, Arch |
Standardtastenkürzel |
P G |
Eingeführt in Version |
0.7 |
Siehe auch |
Keiner |
Beschreibung
Das Werkzeug Draft Vieleck erstellt ein regelmäßiges Vieleck (Polygon) auf der aktuellen Arbeitsebene aus einem Mittelpunkt und einem Radius. Der Radius kann durch Indizieren eines Punktes festgelegt werden.
Ein Draft-Vieleck kann mit der Daten-EigenschaftDraw Mode von inscribed (mit Umkreis) auf circumscribed (mit Inkreis) umgeschaltet werden. Die Ecken eines Draft-Vielecks können mit Rundung (Fillet) oder Fase (Chamfer) versehen werden, indem seine Daten-EigenschaftFillet Radius oder Daten-EigenschaftChamfer Size geändert werden.
Ein durch zwei Punkte, den Mittelpunkt und den Radius, festgelegtes regelmäßiges Vieleck
Anwendung
See also: Draft Tray, Draft Snap and Draft Constrain.
- Es gibt mehrere Möglichkeiten, den Befehl aufzurufen:
- Die Schaltfläche Vieleck drücken.
- Den Menüeintrag Drafting → Vieleck auswählen.
- Das Tastaturkürzel P dann G.
- Der Aufgabenbereich Polygon wird geöffnet. Siehe Optionen für weitere Informationen.
- Die gewünschte Anzahl von Seiten (Sides) eingeben.
- Den ersten Punkt, den Mittelpunkt des Vielecks, in der 3D-Ansicht auswählen, oder Die Koordinaten eingeben und die Schaltfläche Enter point drücken.
- Den zweiten Punkt in der 3D-Ansicht auswählen, oder einen Radius eingeben.
Optionen
Die im Aufgabenbereich vorhandenen Einzelzeichen-Tastaturkürzel können geändert werden. Siehe Draft Einstellungen. Die hier genannten Tastaturkürzel sind die voreingestellten Tastaturkürzel.
- To manually enter the coordinates for the center enter the X, Y and Z component, and press Enter after each. Or you can press the Enter point button when you have the desired values. It is advisable to move the pointer out of the 3D view before entering coordinates.
- Press G or click the Global checkbox to toggle global mode. If global mode is on, coordinates are relative to the global coordinate system, else they are relative to the working plane coordinate system. introduced in version 0.20
- Press L or click the Filled checkbox to toggle filled mode. If filled mode is on, the created polygon will have DatenMake Face set to
true
and will have a filled face. - Press T or click the Continue checkbox to toggle continue mode. If continue mode is on, the command will restart after finishing, allowing you to continue creating polygons.
- Press S to switch Draft snapping on or off.
- Press Esc or the Close button to abort the command.
Hinweise
- Ein Draft-Vieleck kann mit dem Befehl Draft Bearbeiten bearbeitet werden.
Einstellungen
Siehe auch: Voreinstellungseditor und Draft Einstellungen.
- To change the number of decimals used for the input of coordinates and radii: Edit → Preferences... → General → Units → Units settings → Number of decimals.
- To change the initial value of filled mode: Edit → Preferences... → Draft → General settings → Draft tools options → Fill objects with faces whenever possible. Changing the filled mode in a task panel will override this preference for the current FreeCAD session.
- If the Edit → Preferences... → Draft → General settings → Draft tools options → Use Part Primitives when available option is checked, the command will create a Part RegularPolygon instead of a Draft Polygon.
Eigenschaften
Siehe auch: Eigenschafteneditor.
Ein Draft-Vieleck (Polygon-Objekt) wird von einem Part Part2DObject abgeleitet und erbt alle seine Eigenschaften. Außerdem hat es die folgenden zusätzlichen Eigenschaften:
Daten
Draft
- DatenArea (
Area
): (read-only) specifies the area of the face of the polygon. The value will be0.0
if DatenMake Face iffalse
. - DatenChamfer Size (
Length
): specifies the length of the chamfers at the corners of the polygon. - DatenDraw Mode (
Enumeration
): specifies if the polygon isinscribed
in a circle orcircumscribed
around a circle. - DatenFaces Number (
Integer
): specifies the number of sides of the polygon. - DatenFillet Radius (
Length
): specifies the radius of the fillets at the corners of the polygon. - DatenMake Face (
Bool
): specifies if the polygon makes a face or not. If it istrue
a face is created, otherwise only the perimeter is considered part of the object. - DatenRadius (
Length
): specifies the radius of the circle that defines the polygon.
Ansicht
Draft
- AnsichtPattern (
Enumeration
): specifies the Draft Pattern with which to fill the face of the polygon. This property only works if DatenMake Face istrue
and if AnsichtDisplay Mode isFlat Lines
. - AnsichtPattern Size (
Float
): specifies the size of the Draft Pattern.
Skripten
Siehe auch: Autogenerierte API-Dokumentation und FreeCAD Grundlagen Skripten.
To create a Draft Polygon use the make_polygon
method (introduced in version 0.19) of the Draft module. This method replaces the deprecated makePolygon
method.
polygon = make_polygon(nfaces, radius=1, inscribed=True, placement=None, face=None, support=None)
- Creates a
polygon
object with the given number of faces (nfaces
), and based on a circle ofradius
in millimeters. - If
inscribed
isTrue
, the polygon is inscribed in the circle, otherwise it will be circumscribed. - If
placement
isNone
the polygon is created at the origin and one of its vertices will lie on the X axis. - If
face
isTrue
, the polygon will make a face, that is, it will appear filled.
Beispiel:
import FreeCAD as App
import Draft
doc = App.newDocument()
polygon1 = Draft.make_polygon(4, radius=500)
polygon2 = Draft.make_polygon(5, radius=750)
zaxis = App.Vector(0, 0, 1)
p3 = App.Vector(1000, 1000, 0)
place3 = App.Placement(p3, App.Rotation(zaxis, 90))
Polygon3 = Draft.make_polygon(6, radius=1450, placement=place3)
doc.recompute()
- Drafting: Line, Polyline, Fillet, Arc, Arc by 3 points, Circle, Ellipse, Rectangle, Polygon, B-spline, Cubic Bézier curve, Bézier curve, Point, Facebinder, ShapeString, Hatch
- Annotation: Text, Dimension, Label, Annotation styles, Annotation scale
- Modification: Move, Rotate, Scale, Mirror, Offset, Trimex, Stretch, Clone, Array, Polar array, Circular array, Path array, Path link array, Point array, Point link array, Edit, Subelement highlight, Join, Split, Upgrade, Downgrade, Wire to B-spline, Draft to sketch, Set slope, Flip dimension, Shape 2D view
- Draft Tray: Select plane, Set style, Toggle construction mode, AutoGroup
- Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid
- Miscellaneous: Apply current style, Layer, Manage layers, Add a new named group, Move to group, Select group, Add to construction group, Toggle normal/wireframe display, Create working plane proxy, Heal, Show snap toolbar
- Additional: Constraining, Pattern, Preferences, Import Export Preferences, DXF/DWG, SVG, OCA, DAT
- Context menu:
- Layer container: Merge layer duplicates, Add new layer
- Layer: Activate this layer, Select layer contents
- Text: Open hyperlinks
- Wire: Flatten
- Working plane proxy: Write camera position, Write objects state
- Erste Schritte
- Installation: Herunterladen, Windows, Linux, Mac, Zusätzlicher Komponenten, Docker, AppImage, Ubuntu Snap
- Grundlagen: Über FreeCAD, Graphische Oberfläche, Mausbedienung, Auswahlmethoden, Objektname, Programmeinstellungen, Arbeitsbereiche, Dokumentstruktur, Objekteigenschaften, Hilf FreeCAD, Spende
- Hilfe: Tutorien, Video Tutorien
- Arbeitsbereiche: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework