FEM ConstraintTie/pl: Difference between revisions

From FreeCAD Documentation
No edit summary
(Updating to match new version of source page)
Line 33: Line 33:
# Opcjonalnie, zdefiniuj Tolerancję - wiązanie Tie zostanie zastosowane tylko do węzłów powierzchni podrzędnej oddzielonych od powierzchni nadrzędnej odległością nie większą niż określona tutaj.
# Opcjonalnie, zdefiniuj Tolerancję - wiązanie Tie zostanie zastosowane tylko do węzłów powierzchni podrzędnej oddzielonych od powierzchni nadrzędnej odległością nie większą niż określona tutaj.
# {{Version/pl|0.22}}: Opcjonalnie zaznacz pole ''Włącz dopasowanie'', aby umożliwić automatyczne przesuwanie węzłów powierzchni slave, aby leżały na powierzchni master, jeśli biorą udział w działaniu więzu ''(tj. spełniają kryterium tolerancji)''.
# {{Version/pl|0.22}}: Opcjonalnie zaznacz pole ''Włącz dopasowanie'', aby umożliwić automatyczne przesuwanie węzłów powierzchni slave, aby leżały na powierzchni master, jeśli biorą udział w działaniu więzu ''(tj. spełniają kryterium tolerancji)''.

==Cyclic symmetry==

{{Version|0.22}}: Tie constraint can also be used to define cyclic symmetry. This allows the models exhibiting rotational periodic symmetry (repetitive circular patterns around a symmetry axis) to be analyzed using just a single representative sector. It can be particularly useful for rotors, shafts, turbines, fans, flywheels and similar parts, often in combination with [[FEM_ConstraintCentrif|centrifugal load]].
Cyclic symmetry can be defined by selecting the two faces of the cut for tie constraint and setting the following properties:
* {{PropertyData|Cyclic Symmetry}}: setting to ''true'' activates cyclic symmetry
* {{PropertyData|Sectors}}: total number of sectors, equal to the angle of the representative sector divided by 360 (e.g. 8 for 45° sector or 6 for 60° sector)
* {{PropertyData|Connected Sectors}}: number of sectors displayed in results, set it to the same number as {{PropertyData|Sectors}} if you want to visualize the whole 360° part
* {{PropertyData|Symmetry Axis}} - axis of cyclic symmetry - global Z axis by default, can be moved by applying the Placement transformation to the Z versor (similar to what can be done with [[Part_Line|Part Lines]] - to understand how to move the symmetry axis, it might in fact be helpful to change the Placement of Part Line which is usually needed for centrifugal load anyway).
One important limitation of this feature in FEM is that boundary conditions can't be applied to the nodes of the slave surface of cyclic symmetry (slave surface in tie constraint definition) since that would cause an overconstraint. So in some cases, it might be necessary to remove the nodes lying on the edge between the face with the boundary condition and the slave surface of cyclic symmetry from the boundary condition definition. Unfortunately, FreeCAD doesn't operate on node sets and individual nodes can't be deselected so one would have to use workarounds like adding a narrow [[FEM_Geometry_Preparation_and_Meshing#Geometry_partitioning|face partition]] as a transition between the slave surface and the surface with the boundary condition.


<span id="Notes"></span>
<span id="Notes"></span>
==Uwagi==
==Uwagi==


<div class="mw-translate-fuzzy">
* To narzędzie korzysta ze [https://web.mit.edu/calculix_v2.7/CalculiX/ccx_2.7/doc/ccx/node251.html słowa kluczowego *TIE w CalculiX].
* To narzędzie korzysta ze [https://web.mit.edu/calculix_v2.7/CalculiX/ccx_2.7/doc/ccx/node251.html słowa kluczowego *TIE w CalculiX].
</div>





Revision as of 13:19, 12 February 2024

FEM ConstraintTie

Menu location
Model → Warunki brzegowe i obciążenia mechaniczne → Wiązanie tie
Workbenches
MES
Default shortcut
None
Introduced in version
0.19
See also
MES Obciążenie ciśnieniem

Opis

Definiuje wiązanie tie łączące dwie wybrane powierzchnie w taki sposób, że (w przeciwieństwie do tego jak działa kontakt) nie mogą się rozdzielić ani ślizgać po sobie podczas analizy. Są więc trwale połączone.

Użycie

  1. Jest kilka sposobów wywołania tej komendy:
    • Wciśnij przycisk Wiązanie tie.
    • Wybierz opcję Model → Warunki brzegowe i obciążenia mechaniczne → Wiązanie tie z menu.
  2. Wciśnij przycisk Dodaj w panelu zadań a następnie kliknij na ścianie, którą chcesz dodać do definicji wiązania tie. Dokładnie dwie powierzchnie muszą być dodane, jedna po drugiej. Pierwsza wybrana ściana będzie ścianą podrzędną, podczas gdy druga będzie ścianą nadrzędną.
  3. Opcjonalnie, zdefiniuj Tolerancję - wiązanie Tie zostanie zastosowane tylko do węzłów powierzchni podrzędnej oddzielonych od powierzchni nadrzędnej odległością nie większą niż określona tutaj.
  4. dostępne w wersji 0.22: Opcjonalnie zaznacz pole Włącz dopasowanie, aby umożliwić automatyczne przesuwanie węzłów powierzchni slave, aby leżały na powierzchni master, jeśli biorą udział w działaniu więzu (tj. spełniają kryterium tolerancji).

Cyclic symmetry

introduced in version 0.22: Tie constraint can also be used to define cyclic symmetry. This allows the models exhibiting rotational periodic symmetry (repetitive circular patterns around a symmetry axis) to be analyzed using just a single representative sector. It can be particularly useful for rotors, shafts, turbines, fans, flywheels and similar parts, often in combination with centrifugal load. Cyclic symmetry can be defined by selecting the two faces of the cut for tie constraint and setting the following properties:

  • DANECyclic Symmetry: setting to true activates cyclic symmetry
  • DANESectors: total number of sectors, equal to the angle of the representative sector divided by 360 (e.g. 8 for 45° sector or 6 for 60° sector)
  • DANEConnected Sectors: number of sectors displayed in results, set it to the same number as DANESectors if you want to visualize the whole 360° part
  • DANESymmetry Axis - axis of cyclic symmetry - global Z axis by default, can be moved by applying the Placement transformation to the Z versor (similar to what can be done with Part Lines - to understand how to move the symmetry axis, it might in fact be helpful to change the Placement of Part Line which is usually needed for centrifugal load anyway).

One important limitation of this feature in FEM is that boundary conditions can't be applied to the nodes of the slave surface of cyclic symmetry (slave surface in tie constraint definition) since that would cause an overconstraint. So in some cases, it might be necessary to remove the nodes lying on the edge between the face with the boundary condition and the slave surface of cyclic symmetry from the boundary condition definition. Unfortunately, FreeCAD doesn't operate on node sets and individual nodes can't be deselected so one would have to use workarounds like adding a narrow face partition as a transition between the slave surface and the surface with the boundary condition.

Uwagi