Reinforcement Stützenbewehrung
|
Menüeintrag |
---|
3D/BIM → Bewehrungswerkzeuge → Stützenbewehrung |
Arbeitsbereich |
Reinforcement, BIM |
Standardtastenkürzel |
Keiner |
Eingeführt in Version |
0.19 |
Siehe auch |
Reinforcement Stützenbewehrung ZweiBügelSechsStäbe, Reinforcement Stützenbewehrung Ringförmig |
Beschreibung
Das Werkzeug Reinforcement Stützenbewehrung ermöglicht dem Anwender, Bewehrungsstäbe innerhalb einer Stütze (Struktur-Objekt) zu erstellen.
Dieser Befehl ist Teil des Arbeitsbereichs Reinforcement, ein externer Arbeitsbereich, der mit dem Addon-Manager installiert werden kann.
Drei Anwendungsbeispiele stehen zur Verfügung:
- Rechteckige Stütze mit einzelnem Bügel (siehe unten)
- Rechteckige Stütze mit zwei Bügeln und sechs Stäben
- Runde Stütze
Einzelbügel-Bewehrung innerhalb einer Stütze
Anwendung
1. Select any face of a previously created Arch Structure object.
2. Then select Column Reinforcement from the rebar tools.
3. A dialog box will pop-out on screen as shown below.
4. Select the desired type of column reinforcement.
5. Give inputs for data related to ties.
6. Click Next and the dialog box will be updated as shown below.
7. Select desired rebar type and fill data for main rebars.
8. Click Next and the dialog box will be updated as shown below.
9. Select desired rebar type and fill data for xdirection rebars.
10. Click Next and the dialog box will be updated as shown below.
11. Select desired rebar type and fill data for ydirection rebars.
12. Click OK or Apply to generate column reinforcement.
13. Click Cancel to exit the dialog box.
Eigenschaften
Ties:
- DatenLeft Cover: The distance between the left end of the tie to the left face of the structure.
- DatenRight Cover: The distance between the right end of the tie to right face of the structure.
- DatenTop Cover: The distance between tie from the top face of the structure.
- DatenBottom Cover: The distance between tie from the bottom face of the structure.
- DatenOffset: The distance between tie from the top/bottom face of the structure.
- DatenDiameter: Diameter of the tie.
- DatenBent Angle: Bent angle defines the angle at the ends of a tie.
- DatenExtension Factor: Extension Factor defines length of end of tie, expressed in times the diameter.
- DatenNumber: The number of ties.
- DatenSpacing: The distance between the axes of each tie.
Main Rebars: Rebars present at corners of tie
- DatenRebar Type: Type of main rebars.
- DatenHook Orientation: Orientation of LShaped hooks.
- DatenHook Extend Along: Direction for hook extension.
- DatenHook Extension: Length of hook of LShape rebars.
- DatenRounding: A rounding value to be applied to the corners of the LShape rebars, expressed in times the diameter.
- DatenTop Offset: The distance between rebar from the top face of the structure.
- DatenBottom Offset: The distance between rebar from the bottom face of the structure.
- DatenDiameter: Diameter of the main rebars.
XDir Secondary Rebars: Rebars along x-direction except main rebars
- DatenRebar Type: Type of x-direction rebars.
- DatenHook Orientation: Orientation of LShaped hooks.
- DatenHook Extension: Length of hook of LShape rebars.
- DatenRounding: A rounding value to be applied to the corners of the LShape rebars, expressed in times the diameter.
- DatenTop Offset: The distance between rebar from the top face of the structure.
- DatenBottom Offset: The distance between rebar from the bottom face of the structure.
- DatenNumber#Diameter: Number#Diameter set of the x-direction rebars.
YDir Secondary Rebars: Rebars along y-direction except main rebars
- DatenRebar Type: Type of y-direction rebars.
- DatenHook Orientation: Orientation of LShaped hooks.
- DatenHook Extension: Length of hook of LShape rebars.
- DatenRounding: A rounding value to be applied to the corners of the LShape rebars, expressed in times the diameter.
- DatenTop Offset: The distance between rebar from the top face of the structure.
- DatenBottom Offset: The distance between rebar from the bottom face of the structure.
- DatenNumber#Diameter: Number#Diameter set of the y-direction rebars.
Skripten
Siehe auch: Architektur API, Bewehrung API und FreeCAD Grundlagen Skripten.
Das Werkzeug Reinforcement Stützenbewehrung kann in Makros und von der Python-Konsole aus mit den folgenden Funktionen verwendet werden:
Einzel Binder mit vier Stäben erstellen
RebarGroup = makeSingleTieFourRebars(
l_cover_of_tie,
r_cover_of_tie,
t_cover_of_tie,
b_cover_of_tie,
offset_of_tie,
bent_angle,
extension_factor,
dia_of_tie,
number_spacing_check,
number_spacing_value,
dia_of_rebars,
t_offset_of_rebars,
b_offset_of_rebars,
rebar_type="StraightRebar",
hook_orientation="Top Inside",
hook_extend_along="x-axis",
l_rebar_rounding=None,
hook_extension=None,
structure=None,
facename=None,
).rebar_group
- Creates a
RebarGroup
object from the givenstructure
, which is an Arch Structure, andfacename
, which is a face of that structure.- If no
structure
norfacename
are given, it will take the user selected face as input.
- If no
l_cover_of_tie
,r_cover_of_tie
,t_cover_of_tie
,b_cover_of_tie
andoffset_of_tie
are inner offset distances for the tie elements with respect to the faces of the structure. They are respectively the left, right, top, bottom and front/rear offsets.bent_angle
define the angle of the tip of the reinforcement loop.extension_factor
define the length of the tip of the reinforcement loop, expressed in times the diameter.dia_of_tie
is the diameter of the ties.number_spacing_check
if it isTrue
it will create as many ties as given bynumber_spacing_value
; if it isFalse
it will create ties separated by the numerical value ofnumber_spacing_value
.number_spacing_value
specifies the number of ties, or the value of the separation between them, depending onnumber_spacing_check
.dia_of_rebars
is the diameter of the main rebars.t_offset_of_rebars
andb_offset_of_rebars
are inner offset distances for the main rebars with respect to the top and bottom faces of the structure, respectively.rebar_type
is the type of the main rebars; it can be"StraightRebar"
or"LShapeRebar"
.hook_orientation
specifies the orientation of LShaped hook; it can be:"Top Inside"
,"Top Outside"
,"Bottom Inside"
,"Bottom Outside"
,"Top Right"
,"Top Left"
,"Bottom Right"
or"Bottom Left"
.hook_extend_along
specifies direction for hook extension; it can be"x-axis"
or"y-axis"
.l_rebar_rounding
is the parameter that determines the bending radius of the LShaped main rebars, expressed as times the diameter.hook_extension
is the length of hook of LShaped rebars.
Beispiel
import FreeCAD, Draft, Arch
from ColumnReinforcement import SingleTie
# It doesn't work if the structure is not based on a face.
# Structure = Arch.makeStructure(length=1000, width=400, height=400)
Rect = Draft.makeRectangle(400, 400)
Structure = Arch.makeStructure(Rect, height=1600)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
# For Straight Rebars
RebarGroup = SingleTie.makeSingleTieFourRebars(
l_cover_of_tie=40,
r_cover_of_tie=40,
t_cover_of_tie=40,
b_cover_of_tie=40,
offset_of_tie=100,
bent_angle=135,
extension_factor=2,
dia_of_tie=8,
number_spacing_check=True,
number_spacing_value=10,
dia_of_rebars=16,
t_offset_of_rebars=40,
b_offset_of_rebars=40,
rebar_type="StraightRebar",
hook_orientation="Top Inside",
hook_extend_along="x-axis",
l_rebar_rounding=None,
hook_extension=None,
structure=Structure,
facename="Face6",
).rebar_group
# For LShaped Rebars with hook along x-axis
RebarGroup = SingleTie.makeSingleTieFourRebars(
l_cover_of_tie=40,
r_cover_of_tie=40,
t_cover_of_tie=40,
b_cover_of_tie=40,
offset_of_tie=100,
bent_angle=135,
extension_factor=2,
dia_of_tie=8,
number_spacing_check=True,
number_spacing_value=10,
dia_of_rebars=16,
t_offset_of_rebars=-40,
b_offset_of_rebars=-40,
rebar_type="LShapeRebar",
hook_orientation="Top Outside",
hook_extend_along="x-axis",
l_rebar_rounding=2,
hook_extension=40,
structure=Structure,
facename="Face6",
).rebar_group
# For LShaped Rebars with hook along y-axis
RebarGroup = SingleTie.makeSingleTieFourRebars(
l_cover_of_tie=40,
r_cover_of_tie=40,
t_cover_of_tie=40,
b_cover_of_tie=40,
offset_of_tie=100,
bent_angle=135,
extension_factor=2,
dia_of_tie=8,
number_spacing_check=True,
number_spacing_value=10,
dia_of_rebars=16,
t_offset_of_rebars=-40,
b_offset_of_rebars=-40,
rebar_type="LShapeRebar",
hook_orientation="Top Outside",
hook_extend_along="y-axis",
l_rebar_rounding=2,
hook_extension=40,
structure=Structure,
facename="Face6",
).rebar_group
Create Single Tie Multiple Rebars
RebarGroup = makeSingleTieMultipleRebars(
l_cover_of_tie,
r_cover_of_tie,
t_cover_of_tie,
b_cover_of_tie,
offset_of_tie,
bent_angle,
extension_factor,
dia_of_tie,
number_spacing_check,
number_spacing_value,
dia_of_main_rebars,
main_rebars_t_offset,
main_rebars_b_offset,
main_rebars_type="StraightRebar",
main_hook_orientation="Top Inside",
main_hook_extend_along="x-axis",
l_main_rebar_rounding=None,
main_hook_extension=None,
sec_rebars_t_offset=None,
sec_rebars_b_offset=None,
sec_rebars_number_diameter=None,
sec_rebars_type=("StraightRebar", "StraightRebar"),
sec_hook_orientation=("Top Inside", "Top Inside"),
l_sec_rebar_rounding=None,
sec_hook_extension=None,
structure=None,
facename=None,
)
- Creates a
RebarGroup
object from the givenstructure
, which is an Arch Structure, andfacename
, which is a face of that structure.- If no
structure
norfacename
are given, it will take the user selected face as input.
- If no
l_cover_of_tie
,r_cover_of_tie
,t_cover_of_tie
,b_cover_of_tie
andoffset_of_tie
are inner offset distances for the tie elements with respect to the faces of the structure. They are respectively the left, right, top, bottom and front/rear offsets.bent_angle
define the angle of the tip of the reinforcement loop.extension_factor
define the length of the tip of the reinforcement loop, expressed in times the diameter.dia_of_tie
is the diameter of the ties.number_spacing_check
if it isTrue
it will create as many ties as given bynumber_spacing_value
; if it isFalse
it will create ties separated by the numerical value ofnumber_spacing_value
.number_spacing_value
specifies the number of ties, or the value of the separation between them, depending onnumber_spacing_check
.dia_of_main_rebars
is the diameter of the main rebars.main_rebars_t_offset
andmain_rebars_b_offset
are inner offset distances for the main rebars with respect to the top and bottom faces of the structure, respectively.main_rebars_type
is the type of the main rebars; it can be"StraightRebar"
or"LShapeRebar"
.main_hook_orientation
specifies the orientation of main LShaped hook; it can be:"Top Inside"
,"Top Outside"
,"Bottom Inside"
,"Bottom Outside"
,"Top Right"
,"Top Left"
,"Bottom Right"
or"Bottom Left"
.main_hook_extend_along
specifies direction for main hook extension; it can be"x-axis"
or"y-axis"
.l_main_rebar_rounding
is the parameter that determines the bending radius of the LShaped main rebars, expressed as times the diameter.main_hook_extension
is the length of hook of main LShaped rebars.sec_rebars_t_offset
andsec_rebars_b_offset
are tuples (xdir_rebars_t_offset, ydir_rebars_t_offset) and (xdir_rebars_b_offset, ydir_rebars_b_offset) respectively, that defines inner offset distances for the secondary x-direction and y-direction rebars with respect to the top and bottom faces of the structure, respectively.sec_rebars_number_diameter
is a tuple (xdir_rebars_number_diameter, ydir_rebars_number_diameter) that defines number#diameter set of the secondary x-direction and y-direction rebars, respectively.sec_rebars_type
is a tuple (xdir_rebars_type, ydir_rebars_type) that defines the type of secondary x-direction and y-direction rebars ,respectively; it can have"StraightRebar"
or"LShapeRebar"
as rebar type.sec_hook_orientation
is a tuple (xdir_hook_orientation, ydir_hook_orientation) that defines the orientation of secondary x-direction and y-direction LShaped hook; it can have"Top Inside"
,"Top Outside"
,"Bottom Inside"
,"Bottom Outside"
,"Top Right"
,"Top Left"
,"Bottom Right"
or"Bottom Left"
as hook_orientation.l_sec_rebar_rounding
is a tuple (l_xdir_rebar_rounding, l_ydir_rebar_rounding) that determines the bending radius of the LShaped secondary x-direction and y-direction LShaped rebars, expressed as times the diameter of x-direction and y-direction LShaped rebars, respectively.sec_hook_extension
is a tuple (xdir_hook_extension, ydir_hook_extension) that defines the length of hook of secondary x-direction and y-direction LShaped rebars.
Beispiel
import FreeCAD, Draft, Arch
from ColumnReinforcement import SingleTieMultipleRebars
# It doesn't work if the structure is not based on a face
# Structure = Arch.makeStructure(length=1000, width=400, height=400)
Rect = Draft.makeRectangle(400, 400)
Structure = Arch.makeStructure(Rect, height=1600)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
RebarGroup = SingleTieMultipleRebars.makeSingleTieMultipleRebars(
l_cover_of_tie=40,
r_cover_of_tie=40,
t_cover_of_tie=40,
b_cover_of_tie=40,
offset_of_tie=100,
bent_angle=135,
extension_factor=2,
dia_of_tie=8,
number_spacing_check=True,
number_spacing_value=10,
dia_of_main_rebars=16,
main_rebars_t_offset=-40,
main_rebars_b_offset=-40,
main_rebars_type="LShapeRebar",
main_hook_orientation="Top Outside",
main_hook_extend_along="x-axis",
l_main_rebar_rounding=2,
main_hook_extension=40,
sec_rebars_t_offset=(-40, -40),
sec_rebars_b_offset=(-40, -40),
sec_rebars_number_diameter=("2#20mm+1#16mm+2#20mm", "1#20mm+1#16mm+1#20mm"),
sec_rebars_type=("LShapeRebar", "LShapeRebar"),
sec_hook_orientation=("Top Outside", "Top Outside"),
l_sec_rebar_rounding=(2, 2),
sec_hook_extension=(40, 40),
structure=Structure,
facename="Face6",
)
Edition of Single Tie Four Rebars
Die Eigenschaften von Bewehrungsbügeln und Bewehrungsstäben lassen sich mit der folgenden Funktion anpassen:
rebar_group = editSingleTieFourRebars(
rebar_group,
l_cover_of_tie,
r_cover_of_tie,
t_cover_of_tie,
b_cover_of_tie,
offset_of_tie,
bent_angle,
extension_factor,
dia_of_tie,
number_spacing_check,
number_spacing_value,
dia_of_rebars,
t_offset_of_rebars,
b_offset_of_rebars,
rebar_type="StraightRebar",
hook_orientation="Top Inside",
hook_extend_along="x-axis",
l_rebar_rounding=None,
hook_extension=None,
structure=None,
facename=None,
)
rebar_group
is a previously createdColumnReinforcement
group object.- The other parameters are the same as required by the
makeSingleTieFourRebars()
function. structure
andfacename
may be omitted so that the rebar stays in the original structure.
Beispiel
from ColumnReinforcement import SingleTie
rebar_group = SingleTie.editSingleTieFourRebars(
rebar_group,
l_cover_of_tie=40,
r_cover_of_tie=40,
t_cover_of_tie=40,
b_cover_of_tie=40,
offset_of_tie=100,
bent_angle=135,
extension_factor=2,
dia_of_tie=8,
number_spacing_check=True,
number_spacing_value=10,
dia_of_rebars=16,
t_offset_of_rebars=-40,
b_offset_of_rebars=-40,
rebar_type="LShapeRebar",
hook_orientation="Top Outside",
hook_extend_along="x-axis",
l_rebar_rounding=2,
hook_extension=40,
structure=None,
facename=None,
)
Edition of Single Tie Multiple Rebars
Die Eigenschaften von Bewehrungsbügeln und Bewehrungsstäben lassen sich mit der folgenden Funktion anpassen:
rebar_group = editSingleTieMultipleRebars(
rebar_group,
l_cover_of_tie,
r_cover_of_tie,
t_cover_of_tie,
b_cover_of_tie,
offset_of_tie,
bent_angle,
extension_factor,
dia_of_tie,
number_spacing_check,
number_spacing_value,
dia_of_main_rebars,
main_rebars_t_offset,
main_rebars_b_offset,
main_rebars_type="StraightRebar",
main_hook_orientation="Top Inside",
main_hook_extend_along="x-axis",
l_main_rebar_rounding=None,
main_hook_extension=None,
sec_rebars_t_offset=None,
sec_rebars_b_offset=None,
sec_rebars_number_diameter=None,
sec_rebars_type=("StraightRebar", "StraightRebar"),
sec_hook_orientation=("Top Inside", "Top Inside"),
l_sec_rebar_rounding=None,
sec_hook_extension=None,
structure=None,
facename=None,
)
rebar_group
is a previously createdColumnReinforcement
group object.- The other parameters are the same as required by the
makeSingleTieMultipleRebars()
function. structure
andfacename
may be omitted so that the reinforcement stays in the original structure.
Beispiel
from ColumnReinforcement import SingleTieMultipleRebars
rebar_group = SingleTieMultipleRebars.editSingleTieMultipleRebars(
rebar_group,
l_cover_of_tie=40,
r_cover_of_tie=40,
t_cover_of_tie=40,
b_cover_of_tie=40,
offset_of_tie=100,
bent_angle=135,
extension_factor=2,
dia_of_tie=8,
number_spacing_check=True,
number_spacing_value=10,
dia_of_main_rebars=16,
main_rebars_t_offset=-40,
main_rebars_b_offset=-40,
main_rebars_type="LShapeRebar",
main_hook_orientation="Top Outside",
main_hook_extend_along="x-axis",
l_main_rebar_rounding=2,
main_hook_extension=40,
sec_rebars_t_offset=(-40, -40),
sec_rebars_b_offset=(-40, -40),
sec_rebars_number_diameter=("2#20mm+1#16mm+2#20mm", "1#20mm+1#16mm+1#20mm"),
sec_rebars_type=("StraightRebar", "StraightRebar"),
sec_hook_orientation=None,
l_sec_rebar_rounding=None,
sec_hook_extension=None,
structure=None,
facename=None,
)
- 2D drafting: Sketch, Line, Polyline, Circle, Arc, Arc by 3 points, Fillet, Ellipse, Polygon, Rectangle, B-spline, Bézier curve, Cubic Bézier curve, Point
- 3D/BIM: Project, Site, Building, Level, Space, Wall, Curtain Wall, Column, Beam, Slab, Door, Window, Pipe, Pipe Connector, Stairs, Roof, Panel, Frame, Fence, Truss, Equipment
- Reinforcement tools: Custom Rebar, Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement
- Generic 3D tools: Profile, Box, Shape builder..., Facebinder, Objects library, Component, External reference
- Annotation: Text, Shape from text, Aligned dimension, Horizontal dimension, Vertical dimension, Leader, Label, Axis, Axes System, Grid, Section Plane, Hatch, Page, View, Shape-based view
- Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid, Working Plane Top, Working Plane Front, Working Plane Side
- Modify: Move, Copy, Rotate, Clone, Create simple copy, Make compound, Offset, 2D Offset..., Trimex, Join, Split, Scale, Stretch, Draft to sketch, Upgrade, Downgrade, Add component, Remove component, Array, Path array, Circular array, Point array, Cut with plane, Mirror, Extrude..., Difference, Union, Intersection
- Manage: BIM Setup..., Views manager, Manage project..., Manage doors and windows..., Manage IFC elements..., Manage IFC quantities..., Manage IFC properties..., Manage classification..., Manage layers..., Material, Schedule, Preflight checks..., Annotation styles...
- Utils: Toggle bottom panels, Move to Trash, Working Plane View, Select group, Set slope, Create working plane proxy, Add to construction group, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, Toggle subcomponents, Survey, IFC Diff, IFC explorer, Image plane, Unclone, Rewire, Glue, Reextrude
- Panel tools: Panel, Panel Cut, Panel Sheet, Nest
- Structure tools: Structure, Structural System, Multiple Structures
- IFC tools: IFC Diff..., IFC Expand, Make IFC project, IfcOpenShell update
- Nudge: Nudge Switch, Nudge Up, Nudge Down, Nudge Left, Nudge Right, Nudge Rotate Left, Nudge Rotate Right, Nudge Extend, Nudge Shrink
- Additional: Preferences, Fine tuning, Import Export Preferences, IFC, DAE, OBJ, JSON, 3DS, SHP
![](/images/thumb/9/94/User_hub.png/24px-User_hub.png)
- Erste Schritte
- Installation: Herunterladen, Windows, Linux, Mac, Zusätzlicher Komponenten, Docker, AppImage, Ubuntu Snap
- Grundlagen: Über FreeCAD, Graphische Oberfläche, Mausbedienung, Auswahlmethoden, Objektname, Programmeinstellungen, Arbeitsbereiche, Dokumentstruktur, Objekteigenschaften, Hilf FreeCAD, Spende
- Hilfe: Tutorien, Video Tutorien
- Arbeitsbereiche: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework