PartDesign Draft/de: Difference between revisions

From FreeCAD Documentation
No edit summary
(Created page with ":''Nicht vergessen'': :* Da das Werkzeug immer mindestens eine Fläche erfordert, kann die letzte vorhandene Fläche nicht aus der Liste entfernt werden.")
Line 50: Line 50:




:''Remember'':
:''Nicht vergessen'':
:* Da das Werkzeug immer mindestens eine Fläche erfordert, kann die letzte vorhandene Fläche nicht aus der Liste entfernt werden.
:* Since there must be at least one face for the feature, the last remaining face in the list cannot be removed.


=== Eine Formschräge bearbeiten ===
=== Eine Formschräge bearbeiten ===

Revision as of 18:07, 5 June 2022

PartDesign Formschräge

Menüeintrag
Part Design → Modifikationen → Formschräge
Arbeitsbereich
Part Design
Standardtastenkürzel
-
Eingeführt in Version
-
Siehe auch
Keine

Beschreibung

Das Werkzeug PartDesign Formschräge versieht die ausgewähleten Flächen eines Objekts mit einer (Entform-)Schräge. Es fügt dem Dokument ein Draft-Objekt und den dazugehörigen Repräsentanten in der Baumansicht hinzu.

Select one or more faces of the object before starting the tool. Here, 2 faces have been selected.
Showing Draft Parameters in TaskPanel.
2 faces have been added, and a 10 deg. draft applied. The bottom plane has remained dimensionally stable, while the draft has made the top plane smaller.
The Neutral Plane has been changed to the top. Now, the top plane has stayed dimensionally stable, while the draft has made the bottom plane larger.
Pull direction is set to the lower right edge, resulting in the draft pulling to the left.
Checking the Reverse Direction box has applied an inward draft rather than outward.

Anwendung

Eine Formschräge hinzufügen

  1. Falls nötig, wird der abzuschrägende Körper aktiviert.
  2. Eine oder mehrere Flächen des Körpers auswählen.
  3. Es gibt mehrere Möglichkeiten das Werkzeug aufzurufen:
    • Die Schaltfläche Formschräge drücken.
    • Den Menüeintrag Part Design → Modifikationen → Formschräge auswählen.
  4. Wenn kein Körper aktiv ist und sich zwei oder mehr Körper im Dokument befinden, offnet sich der Dialog Active Body Required und fordert zur Aktivierung eines Körpers auf. Ist nur ein einziger Körper vorhanden, wird er automatisch ausgewählt.
  5. Der Aufgabenbereich Parameter der Formschräge wird geöffnet. Siehe Optionen für weitere Informationen.
  6. Zum Fertigstellen die OK-Schaltfläche drücken.


Nicht vergessen:
  • Da das Werkzeug immer mindestens eine Fläche erfordert, kann die letzte vorhandene Fläche nicht aus der Liste entfernt werden.

Eine Formschräge bearbeiten

  1. Eine der folgenden Möglichkeiten startet die Bearbeitung:
    • Das Draft-Objekt in der Baumansicht doppelt anklicken.
    • Das Draft-Objekt in der Baumansicht mit der rechten Maustaste anklicken und Draft bearbeiten aus dem Kontextmenü auswählen.
  2. Der Aufgabenbereich Parameter der Formschräge wird geöffnet. Siehe Optionen für weitere Informationen.
  3. Zum Fertigstellen die OK-Schaltfläche drücken.

Optionen

  • Draft angle: Set the Draft angle either by entering a value or by clicking the up/down arrows.
  • Add face: Add faces to the selection by pressing the Add face button and selecting more faces.
  • Remove face: Choose a way to remove faces from the selection:
    • Select one or more faces in the list and press the Del key or right-click the list and select Remove from the context menu.
    • Press the Remove face button. All previously selected faces are highlighted in purple. Select each face to be removed.
  • Neutral plane: Set the the neutral plane by pressing the Neutral plane button and selecting the plane that must not change dimensionally.
  • Pull direction: Set the the pull direction by pressing the Pull direction button, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable.
  • Reverse pull direction: Invert the pull direction by checking the Reverse pull direction checkbox. This will toggle the draft between positive and negative angles.

Hinweise

  • Das Werkzeug Formschräge arbeitet nur mit Flächen, die nicht tangential mit anderen Flächen verbunden sind. (Hier sollte das englische Original präzisiert werden...) A common mistake is to attempt to apply draft to a face that already has a fillet applied to it. To solve this, remove the fillet, apply the draft as needed, then re-apply the fillet.

Eigenschaften

Siehe auch: Eigenschafteneditor.

Ein PartDesign-Draft-Objekt wird von einem Part-Formelement abgeleitet und erbt alle seine Eigenschaften. Außerdem hat es die folgenden zusätzlichen Eigenschaften:

Daten

Basis

  • DatenAngle (Angle): Cannot be negative. Default: 1.5 °.
  • DatenReversed (Bool): Default: false.
  • DatenBase (LinkSub): Sub-link to the parent feature's list of selected edges and faces.
  • DatenSupport Transform (Bool): "Include the base additive/subtractive shape when used in pattern features. If disabled, only the dressed part of the shape is used for patterning". Default: false.
  • Daten (hidden)Add Sub Shape (PartShape)
  • Daten (hidden)Base Feature (Link): Link to the parent feature.
  • Daten (hidden)_ Body (LinkHidden): Link to the parent body.

Draft

  • DatenNeutral Plane (LinkSub): Sub-link to the parent feature's list containing the neutral plane.
  • DatenPull Direction (LinkSub)

Part Design

  • DatenRefine (Bool): "Refine shape (clean up redundant edges) after adding/subtracting". The default value is determined by the Automatically refine model after sketch-based operation preference. See PartDesign Preferences.