Sketcher CreatePolyline/ro: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
 
Line 40: Line 40:
#* Use the keyboard shortcut: {{KEY|G}} then {{KEY|M}}.
#* Use the keyboard shortcut: {{KEY|G}} then {{KEY|M}}.
# The cursor changes to a cross with the tool icon.
# The cursor changes to a cross with the tool icon.
# A polyline always starts with a straight line segment: pick two points to define this segment.
# The modes of the tool require a previous segment. Do one of the following:
#* Pick two points to define a line segment.
#* Pick the endpoint of an existing line or arc segment ([[Sketcher_Workbench#Auto_constraints|Auto constraints]] must be enabled).
# Optionally press the {{KEY|M}} key one or more times to cycle through the modes for the next segment. The available modes are:
# Optionally press the {{KEY|M}} key one or more times to cycle through the modes for the next segment. The available modes are:
#* Line perpendicular to the previous segment.
#* Line perpendicular to the previous segment.
#* Line tangential to the previous segment.
#* Line tangential to the previous segment (this is the initial mode if the previous segment is an arc).
#* Arc tangential to the previous segment.
#* Arc tangential to the previous segment.
#* Arc perpendicular (left) to the previous segment.
#* Arc perpendicular (left) to the previous segment.
#* Arc perpendicular (right) to the previous segment.
#* Arc perpendicular (right) to the previous segment.
#* Line only connected to the previous segment. This is the initial mode again.
#* Line only connected to the previous segment.
# While in any of the arc modes, optionally hold down the {{KEY|Ctrl}} key to snap the arc to increments of 45° relative to the previous segment.
# While in any of the arc modes, optionally hold down the {{KEY|Ctrl}} key to snap the arc to increments of 45° relative to the previous segment.
# Pick the endpoint of the segment.
# Pick the endpoint of the segment.

Latest revision as of 14:25, 23 April 2024

Sketcher CreatePolyline

poziția meniului
Sketch → Sketcher geometries → Create polyline
Ateliere
Sketcher
scurtătură
nici unul
Prezentat în versiune
-
A se vedea, de asemenea,
Sketcher Line

Descriere

Această unealtă funcționează ca un instrument Sketcher CreateLine, dar crează linii și arce de cerc conectate prin vârfuri/vertex-uri. Când pornește instrumentul, indicatorul mouse se modifică într-o cruce albă și o iconiță roșie tip polilinie. coordonatele indicatorului sunt afișate alături în albastru și în timp real.

Polyline începe cu o linie, un arc de cerc tangent, un arc de cerc perpendicular și apoi cu o linie tangentă

Cum se folosește

See also: Drawing aids.

  1. There are several ways to invoke the tool:
    • Press the Create polyline button.
    • Select the Sketcher → Sketcher geometries → Create polyline option from the menu.
    • Right-click in the 3D view and select the Create polyline option from the context menu.
    • Use the keyboard shortcut: G then M.
  2. The cursor changes to a cross with the tool icon.
  3. The modes of the tool require a previous segment. Do one of the following:
    • Pick two points to define a line segment.
    • Pick the endpoint of an existing line or arc segment (Auto constraints must be enabled).
  4. Optionally press the M key one or more times to cycle through the modes for the next segment. The available modes are:
    • Line perpendicular to the previous segment.
    • Line tangential to the previous segment (this is the initial mode if the previous segment is an arc).
    • Arc tangential to the previous segment.
    • Arc perpendicular (left) to the previous segment.
    • Arc perpendicular (right) to the previous segment.
    • Line only connected to the previous segment.
  5. While in any of the arc modes, optionally hold down the Ctrl key to snap the arc to increments of 45° relative to the previous segment.
  6. Pick the endpoint of the segment.
  7. Optionally repeat this to create more segments.
  8. To finish the input do one of the following:
    • Snap to the start point to create a closed polyline.
    • Right-click or press Esc to create an open polyline.
  9. The polyline segments have been created and applicable constraints have been added.
  10. If the tool runs in continue mode:
    1. Optionally keep creating polylines.
    2. To finish, right-click or press Esc, or start another geometry or constraint creation tool.