Kreslení kružnice
Kreslení_Kružnice |
Umístění Menu |
---|
Kreslení -> Kružnice |
Pracovní stoly |
Kreslení, Architektura |
Výchozí zástupce |
C I |
Představen ve verzi |
- |
Viz také |
Kreslení oblouk |
Description
Popis
Nástroj Kružnice vytváří kružnici v aktuální pracovní rovině zadáním dvou bodů: střed a poloměr nebo zadáním tečen nebo kombinací obou způsobů. Použije se tloušťka čáry a barva předem zadaná v záložce Nástrojů. Tento nástroj pracuje stejně jako nástroj Oblouk, kromě toho, že se končí po zadání poloměru.
A Draft Circle can be turned into an arc by setting its ÚdajeFirst Angle and ÚdajeLast Angle properties to different values.
Usage
See also: Draft Tray, Draft Snap and Draft Constrain.
Použití
- Stiskněte tlačítko Kružnice nebo klávesy C pak I
- Klikněte na první bod ve 3D pohledu nebo zadejte souřadnice
- Klikněte na druhý bod ve 3D pohledu nebo zadejte hodnotu poloměru.
Options
The single character keyboard shortcuts available in the task panel can be changed. See Draft Preferences. The shortcuts mentioned here are the default shortcuts.
Volby
- Základní způsob použití nástrije Kružnice je zadáním dvou bodů, středu a bodu na obvodu kružnice, který definuje poloměr.
- Stiskem ALT můžete vybrat tečnu místo zadání druhého bodu. Můžete tak zkonstruovat několik typů kružnic výběrem jedné dvou nebo tří tečen.
- Chcete-li zadat souřadnice ručně, jdenoduše vkládejte čísla a stiskněte ENTER mezi každou z komponent X, Y a Z.
- Stiskněte klávesu T nebo klikněte na zaklikávací políčko pro zatrhnutí nebo odtrhnutí tlačítka Pokračovat. Je-li nastaven pokračovací mód, bude nástroj Kružnice hned po zadání druhého bodu připraven ke kreslení další kružnice bez nutnosti stisknout znovu tlačítko Kružnice.
- Stisknutím klávesy CTRL během kreslení vynutíte přichycení vašeho bodu k nejbližšímu uchopovacímu místu nezávisle na vzálenosti od něho.
- Stisknutím klávesy SHIFT během kreslení nastavíte vazbu vašeho bodu svisle nebo vodorovně v relaci ke středu.
- Stisknutím klávesy I nebo tlačítka Filled zajistíte, že se kružnice tváří jako plocha (musí být uzavřená). Jednoduše se to nastavuje Pohled->Vlastnost Kružnice na "Otevřené čáry" nebo "Drátový model", toto také může být snadno změněno později.
- Stiskněte klávesu ESC nebo tlačítko Cancel pro ukončení aktuálního příkazu.
- Kružnice může být po vytvoření změněna na oblouk nastavením počátečního a koncového úhlu na jiné hodnoty.
- Když je Kružnice v zobrazovacím módu "Jednoduché čáry" může zobrazovat šrafovací vzor nastavením vlastnosti "Vzor" dole.
Notes
- A Draft Circle can be edited with the Draft Edit command.
Preferences
See also: Preferences Editor and Draft Preferences.
- To change the number of decimals used for the input of coordinates and radii: Edit → Preferences... → General → Units → Units settings → Number of decimals.
- To change the initial value of filled mode: Edit → Preferences... → Draft → General settings → Draft tools options → Fill objects with faces whenever possible. Changing the filled mode in a task panel will override this preference for the current FreeCAD session.
- If the Edit → Preferences... → Draft → General settings → Draft tools options → Use Part Primitives when available option is checked, the command will create a Part Circle instead of a Draft Circle.
Properties
See also: Property editor.
A Draft Circle object is derived from a Part Part2DObject and inherits all its properties. It also has the following additional properties:
Data
Draft
- ÚdajeArea (
Area
): (read-only) specifies the area of the face of the circle. The value will be0.0
if ÚdajeMake Face iffalse
or the face cannot be created. - ÚdajeFirst Angle (
Angle
): specifies the start angle of the circle, normally0°
. - ÚdajeLast Angle (
Angle
): specifies the end angle of the circle, normally0°
. - ÚdajeMake Face (
Bool
): specifies if the circle makes a face or not. If it istrue
a face is created, otherwise only the perimeter is considered part of the object. This property only works if the ÚdajeFirst Angle and ÚdajeLast Angle have the same value. Note that0°
and360°
are not considered the same. - ÚdajeRadius (
Length
): specifies the radius of the circle.
View
Draft
- PohledPattern (
Enumeration
): specifies the Draft Pattern with which to fill the face of the circle. This property only works if ÚdajeMake Face istrue
and if PohledDisplay Mode isFlat Lines
. - PohledPattern Size (
Float
): specifies the size of the Draft Pattern.
Scripting
Skriptování
Nástroj Kružnice může být využit v makrech a z konzoly Pythonu použitím následující funkce:
To create a Draft Circle use the make_circle
method (introduced in version 0.19) of the Draft module. This method replaces the deprecated makeCircle
method.
circle = make_circle(radius, placement=None, face=None, startangle=None, endangle=None, support=None)
circle = make_circle(Part.Edge, placement=None, face=None, startangle=None, endangle=None, support=None)
- Vytvoří objekt kružnice podle daného poloměru.
- Je-li zadáno placement (umístění), je využito.
- Je-li facemode (mód plochy) False, bude kružnice zobrazena jako drát, jinak jako plocha.
- Jsou-li zadány počáteční a koncový úhel (startangle a endangle) (ve stupních), jsou využity a objekt se zobrazí jako oblouk.
- Výstupem je nově vytvořený objekt.
Příklad:
import FreeCAD as App
import Draft
doc = App.newDocument()
circle1 = Draft.make_circle(200)
zaxis = App.Vector(0, 0, 1)
p2 = App.Vector(1000, 1000, 0)
place2 = App.Placement(p2, App.Rotation(zaxis, 0))
circle2 = Draft.make_circle(500, placement=place2)
p3 = App.Vector(-1000, -1000, 0)
place3 = App.Placement(p3, App.Rotation(zaxis, 0))
circle3 = Draft.make_circle(750, placement=place3)
doc.recompute()
- Drafting: Line, Polyline, Fillet, Arc, Arc by 3 points, Circle, Ellipse, Rectangle, Polygon, B-spline, Cubic Bézier curve, Bézier curve, Point, Facebinder, ShapeString, Hatch
- Annotation: Text, Dimension, Label, Annotation styles, Annotation scale
- Modification: Move, Rotate, Scale, Mirror, Offset, Trimex, Stretch, Clone, Array, Polar array, Circular array, Path array, Path link array, Point array, Point link array, Edit, Subelement highlight, Join, Split, Upgrade, Downgrade, Wire to B-spline, Draft to sketch, Set slope, Flip dimension, Shape 2D view
- Draft Tray: Select plane, Set style, Toggle construction mode, AutoGroup
- Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid
- Miscellaneous: Apply current style, Layer, Manage layers, Add a new named group, Move to group, Select group, Add to construction group, Toggle normal/wireframe display, Create working plane proxy, Heal, Show snap toolbar
- Additional: Constraining, Pattern, Preferences, Import Export Preferences, DXF/DWG, SVG, OCA, DAT
- Context menu:
- Layer container: Merge layer duplicates, Add new layer
- Layer: Activate this layer, Select layer contents
- Text: Open hyperlinks
- Wire: Flatten
- Working plane proxy: Write camera position, Write objects state
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Assembly, BIM, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub