Sketcher ConstrainCoincident/it: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 18: Line 18:
==Descrizione==
==Descrizione==


Affixes a point onto (coincident with) one or more other points. {{Version|1.0}}: It acts as a concentric constraint if two or more circles, arcs, ellipses or arcs of ellipses are selected.
Crea un vincolo di Coincidenza di punti sull'elemento selezionato


==Utilizzo==
Questo strumento di vincolo richiede e accetta come argomento due punti e serve per rendere i due punti ''coincidenti''. (Nel senso di trasformarli in un unico punto.)


# Do one of the following:
Nella pratica è utile quando un profilo è interrotto - per esempio dove due punti di finelinea sono uno accanto all'altro, ma le linee devono essere unite. In questo caso, un vincolo di coincidenza sui rispettivi punti finali chiude la breccia.
#* Select two or more points.

#* Select two or more edges of circles, arcs, ellipses or arcs of ellipses.
==Utilizzo==
# There are several ways to invoke the command:

#* Press the {{Button|[[File:Sketcher_ConstrainCoincident.svg|16px]] [[Sketcher_ConstrainCoincident|Constrain coincident]]}} button in the toolbar.
<div class="mw-translate-fuzzy">
#* Use the {{KEY|C}} keyboard shortcut.
Come detto in precedenza, questo strumento richiede due argomenti e entrambi devono essere dei punti.
#* Use the {{MenuCommand|Sketch → Sketcher constraints → [[File:Sketcher_ConstrainCoincident.svg|16px]] Constrain coincident}} entry in the top menu.
#In primo luogo è necessario evidenziare due punti distinti. (Nota: lo strumento non funziona quando si tenta di selezionare il punto iniziale e quello finale della stessa linea).
#Per evidenziare un elemento del disegno, spostare il mouse sopra l'oggetto e fare clic con il pulsante sinistro del mouse.
#Un elemento selezionato assume il colore verde. Il colore è modificabile da {{MenuCommand|Modifica → Preferenze → Visualizzazione → Colori → Selezione}}.
#Elementi successivi possono essere selezionati ripetendo la procedura precedente. NOTA: Non è necessario tenere premuto nessun tasto speciale, tipo {{KEY|Ctrl}}, per aggiungere elementi del disegno alla selezione multipla.
#Dopo aver evidenziato due punti, si può invocare il comando in uno di questi modi:
#* Cliccare sull'icona {{Button|[[File:Sketcher_ConstrainCoincident.svg|16px]] Coincidenza}} della barra degli strumenti.
#* Usare la scorciatoia da tastiera {{KEY|C}}.
#* Usare la voce {{MenuCommand|Sketch → Vincoli → Coincidenza}} dal menu principale.
{{Emphasis|Risultato:}} il comando fa sì che i due punti diventino "coincidenti" e vengano sostituiti da un singolo punto.
</div>

NOTA: Per rendere due punti coincidenti, FreeCAD deve necessariamente spostare uno o entrambi i punti originali.


== Alternatives to Coincident constraint ==
== Alternatives to Coincident constraint ==

Revision as of 08:56, 1 December 2022

Coincidenza

Posizione nel menu
Sketch → Vincoli → Coincidenza
Ambiente
Schizzo
Avvio veloce
C
Introdotto nella versione
-
Vedere anche
Blocca, Punto su oggetto

Descrizione

Affixes a point onto (coincident with) one or more other points. introduced in version 1.0: It acts as a concentric constraint if two or more circles, arcs, ellipses or arcs of ellipses are selected.

Utilizzo

  1. Do one of the following:
    • Select two or more points.
    • Select two or more edges of circles, arcs, ellipses or arcs of ellipses.
  2. There are several ways to invoke the command:
    • Press the Constrain coincident button in the toolbar.
    • Use the C keyboard shortcut.
    • Use the Sketch → Sketcher constraints → Constrain coincident entry in the top menu.

Alternatives to Coincident constraint

The two constrained items of a Coincident constraint must be start point or end point vertices, or center points of arcs, circles or ellipses. Some combinations which are not possible with a coincident constraint can be emulated using other constraints:

  • The Symmetric constraint can be used to place a start point, end point or center point on the midpoint of a straight line.
  • A midpoint-to-midpoint placement of two straight lines can be achieved by creating a new Point and using two Symmetric constraints so that it lies on the midpoint of both lines.
  • A vertex can be constrained to lie along an edge using a PointOnObject constraint. Note that with this constraint, the point can lie anywhere on the full extension of a segment or curve (i.e. also before the start point or beyond the end point).
  • A collinear placement of two straight lines can be obtained by applying a Tangent constraint to them, or by combining a PointOnObject constraint and a Parallel constraint.
  • Two edges can be made identical by using two Coincident constraints, one for each pair of extremities.
  • Two circles can be made identical by using a Coincident constraint to merge the centers, and applying an Equal constraint to their edges. For arcs, this will ensure both arcs are part of the same circle, while allowing them to have different start and end points.

Script generico

Il vincolo può essere creato dalle macro e dalla console python utilizzando il seguente comando:

The constraint can be created from macros and from the Python console by using the following command:

Sketch.addConstraint(Sketcher.Constraint('Coincident',LineFixed,PointOfLineFixed,LineMoving,PointOfLineMoving))

dove:

  • Sketch è un oggetto schizzo.
  • LineFixed è il numero della linea, che non deve muoversi applicando il vincolo.
  • PointOfLineFixed è il numero del vertice della linea LineFixed che deve soddisfare il vincolo.
  • LineMoving è il numero della linea che si sposterà applicando il vincolo.
  • PointOfLineMoving è il numero della linea LineMoving che deve soddisfare il vincolo.

As the names LineFixed and LineMoving indicate, if both constrained vertices are free to move in any direction, the first one (first to be selected in the Gui) will remain fixed and the other one will move. In the presence of existing constraints, however, both edges may move.

The Sketcher scripting page explains the values which can be used for LineFixed, PointOfLineFixed, LineMoving and PointOfLineMoving, and contains further examples on how to create constraints from Python scripts.