Arch Лестница
Лестница |
Системное название |
---|
Arch_Stairs |
Расположение в меню |
Arch → Лестница |
Верстаки |
Arch |
Быстрые клавиши |
S R |
Представлено в версии |
0.14 |
См. также |
Структура, Оборудование |
Описание
Инструмент Лестница позволяет автоматически создавать несколько типов лестниц. инструмент позволяет автоматически создавать несколько типов лестниц. На данный момент поддерживаются только прямые лестницы (лестничной площадкой или без нее). Лестница может быть построена с нуля или вдоль Линии (верстак Draft). Если линия не горизонтальна, а имеет наклон по вертикали, лестница также будет иметь наклон.
См. Stairs entry in wikipedia для определения различных терминов, используемых для описания частей лестницы.
Изображение двух сконструированных лестниц, одна с массивной конструкцией и лестничной площадкой, а другая с одним стрингером.
Опции
- Лестницы разделяют общие свойства и поведение всех Arch Components
Применение
- Нажмите кнопку Лестница или нажмите клавиши S, R.
- Настройте нужные свойства. Некоторые части лестницы, такие как конструкция, могут изначально отсутствовать, если какое-либо из свойств делает это невозможным, например, толщина конструкции равна 0.
Свойства
Данные
Segment and Parts
- ДанныеAbs Top (
Vector
): (read-only) The absolute top level the stairs lead to. - ДанныеLast Segment (
Link
): Last segment (flight or landing) of an Arch Stairs connecting to this segment. The start level of the stairs will be the end level of this last segment. - ДанныеOutline Left (
VectorList
): The left outline of the stairs. - ДанныеOutline Left All (
VectorList
): The left outline of all segments of the stairs. - ДанныеOutline Right (
VectorList
): The right outline of the stairs. - ДанныеOutline Right All (
VectorList
): The right outline of all segments of the stairs. - ДанныеRailing Height Left (
Length
): Height of the left railing of the stairs or landing. - ДанныеRailing Height Right (
Length
): Height of the right railing of the stairs or landing. - ДанныеRailing Left (
String
): Name of the left railing object. - ДанныеRailing Offset Left (
Length
): Offset of the left railing from the edge of the stairs or landing. - ДанныеRailing Offset Right (
Length
): Offset of the right railing from the edge of the stairs or landing. - ДанныеRailing Right (
String
): Name of the right railing object.
Stairs (Лестница)
- ДанныеAlign (
Enumeration
): The alignment of the stairs on the baseline. Only used if a baseline is defined. Can beLeft
,Right
orCenter
. - ДанныеHeight (
Length
): The total height of the stairs. Only used if no baseline is defined, or if the baseline is horizontal. Ignored if ДанныеRiser Height Enforce is non-zero. - ДанныеLength (
Length
): The total length of the stairs if no baseline is defined. Ignored if ДанныеTread Depth Enforce is non-zero. - ДанныеWidth (
Length
): The width of the stairs. - ДанныеWidth of Landing (
FloatList
): If the ДанныеNumber Of Steps is 1, the stairs object acts as a landing. When this is the case and the baseline is multi-segment, the width of first segment of the landing follows the ДанныеWidth, the widths of subsequent segments follow the list set here.
Steps (Ступени)
- ДанныеBlondel Ratio (
Float
): (только для чтения) Рассчитанный коэффициент Блонделя. Это соотношение позволяет определить наиболее удобную для человека лестницу и должно составлять от 62 до 64 см или от 24,5 до 25,5 дюйма. - ДанныеLanding Depth (
Length
): Длина лестничной площадки находящейся по ходу лестницы, указывается только если площадка ДанныеLandings добавлена. По умолчанию значение ДанныеWidth равно 0. - ДанныеNosing (
Length
): Размер выступа ступени. - ДанныеNumber Of Steps (
Integer
): Количество ступеней (подступенников). - ДанныеRiser Height (
Length
): (только для чтения) Высота подступенников лестницы. Если высота ступеней ДанныеRiser Height Enforce равна нулю, тогда она вычисляется как (ДанныеHeight / ДанныеNumber of Steps). В других случаях это значение эквивалентно ДанныеRiser Height Enforce. - ДанныеRiser Height Enforce (
Length
): Принудительная высота подступенников лестницы. - ДанныеRiser Thickness (
Length
): Толщина подступенников лестницы. - ДанныеTread Depth (
Length
): (только для чтения) Длина ступеней. Если ДанныеTread Depth Enforce равно 0, то вычисляется как (ДанныеLength / ДанныеNumber of Steps). В других случаях это значение эквивалентно ДанныеTread Depth Enforce. - ДанныеTread Depth Enforce (
Length
): Принудительная длина ступеней - ДанныеTread Thickness (
Length
): Толщина ступеней.
Structure
- ДанныеConnection Down Start Stairs (
Enumeration
): The type of connection between the lower floor slab and the start of the stairs. Can beHorizontalCut
,VerticalCut
orHorizontalVerticalCut
. - ДанныеConnection End Stairs Up (
Enumeration
): The type of connection between the end of the stairs and the upper floor slab. Can betoFlightThickness
ortoSlabThickness
. - ДанныеDown Slab Thickness (
Length
): The thickness of the lower floor slab. - ДанныеFlight (
Enumeration
): The direction of the flight after the landing. Can beStraight
,HalfTurnLeft
orHalfTurnRight
. - ДанныеLandings (
Enumeration
): The type of landings. Can beNone
orAt center
(At each corner
not implemented yet). - ДанныеStringer Overlap (
Length
): The overlap of the stringers above the bottom of the treads. - ДанныеStringer Width (
Length
): The width of the stringers. - ДанныеStructure (
Enumeration
): The structure type of the stairs. Can beNone
,Massive
,One stringer
orTwo stringers
. - ДанныеStructure Offset (
Length
): The offset between the border of the stairs and the structure. - ДанныеStructure Thickness (
Length
): The thickness of the structure. - ДанныеUp Slab Thickness (
Length
): The thickness of the upper floor slab. - ДанныеWinders (
Enumeration
): The type of winders. Not implemented.
Ограничения
- На данный момент доступны только прямые лестницы
- См. тему на форуме про круговые лестницы.
- См. уведомления о данном инструменте на форуме.
Программирование
См. так же: Arch API и Основы составления скриптов в FreeCAD.
The Stairs tool can be used in macros and from the Python console by using the following function:
Stairs = makeStairs(baseobj=None, length=None, width=None, height=None, steps=None, name="Stairs")
- Creates a
Stairs
object from the givenbaseobj
. - If
baseobj
is not given, it will uselength
,width
,height
, andsteps
, to build a solid object.
Пример:
import Arch
Stairs = Arch.makeStairs(length=5000, width=1200, height=3000, steps=14)
- Elements: Wall, Structure, Curtain Wall, Window, Roof, Space, Stairs, Equipment, Frame, Fence, Truss, Profile, Pipe, Pipe Connector
- Reinforcements: Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement, Custom Rebar
- Panels: Panel, Panel Cut, Panel Sheet, Nest
- Materials: Material, Multi-Material
- Organization: Building Part, Project, Site, Building, Level, External reference, Section Plane, Schedule
- Axes: Axis, Axes system, Grid
- Modification: Cut with plane, Add component, Remove component, Survey
- Utilities: Component, Clone component, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, 3 Views from mesh, Create IFC spreadsheet, Toggle Subcomponents
- Additional: Preferences, Import Export Preferences (IFC, DAE, OBJ, JSON, 3DS, SHP), IfcOpenShell, IfcPlusPlus, Arch API
- Начинающим
- Установка: Загрузка, Windows, Linux, Mac, Дополнительных компонентов, Docker, AppImage, Ubuntu Snap
- Базовая: О FreeCAD, Интерфейс, Навигация мыши, Методы выделения, Имя объекта, Настройки, Верстаки, Структура документа, Свойства, Помоги FreeCAD, Пожертвования
- Помощь: Учебники, Видео учебники
- Верстаки: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework