Arch Лестница
|
|
| Расположение в меню |
|---|
| Arch → Лестница |
| Верстаки |
| Arch |
| Быстрые клавиши |
| S R |
| Представлено в версии |
| 0.14 |
| См. также |
| Структура, Оборудование |
Описание
Инструмент Лестница позволяет автоматически создавать несколько типов лестниц. инструмент позволяет автоматически создавать несколько типов лестниц. На данный момент поддерживаются только прямые лестницы (лестничной площадкой или без нее). Лестница может быть построена с нуля или вдоль Линии (верстак Draft). Если линия не горизонтальна, а имеет наклон по вертикали, лестница также будет иметь наклон.
Смотрите статью о лестницах на википедии для определения значения различных терминов, используемых при описании частей лестницы.
Изображение двух сконструированных лестниц, одна с массивной конструкцией и лестничной площадкой, а другая с одним косоуром.
Опции
Применение
- Нажмите кнопку
Лестница или нажмите клавиши S, R.
- Настройте нужные свойства. Некоторые части лестницы, такие как конструкция, могут изначально отсутствовать, если какое-либо из свойств делает это невозможным, например, толщина конструкции равна 0.
Complex stairs based on a selection of lines and wired as shown on the left.
In red the wires used for the landings at Z=1500mm, Z=3000mm and Z=4500mm.
In black the lines connecting them used for the flights.
Свойства
An Arch Stairs object shares the common properties and behaviors of all Arch Components.
Данные
Segment and Parts
- ДанныеAbs Top (
Vector): (read-only) The absolute top level the stairs lead to. - ДанныеLast Segment (
Link): Last segment (flight or landing) of an Arch Stairs connecting to this segment. The start level of the stairs will be the end level of this last segment. - ДанныеOutline Left (
VectorList): The left outline of the stairs (read-only). - ДанныеOutline Left All (
VectorList): The left outline of all segments of the stairs (read-only). - ДанныеOutline Right (
VectorList): The right outline of the stairs (read-only). - ДанныеOutline Right All (
VectorList): The right outline of all segments of the stairs (read-only). - ДанныеRailing Height Left (
Length): Height of the left railing of the stairs or landing. - ДанныеRailing Height Right (
Length): Height of the right railing of the stairs or landing. - ДанныеRailing Left (
LinkHidden): The left railing object. introduced in 0.20: Property type updated fromStringtoLinkHidden. - ДанныеRailing Offset Left (
Length): Offset of the left railing from the edge of the stairs or landing. - ДанныеRailing Offset Right (
Length): Offset of the right railing from the edge of the stairs or landing. - ДанныеRailing Right (
LinkHidden): The right railing object. introduced in 0.20: Property type updated fromStringtoLinkHidden.
Stairs (Лестница)
- ДанныеAlign (
Enumeration): The alignment of the stairs on the baseline. Only used if a baseline is defined. Can beLeft,RightorCenter. - ДанныеHeight (
Length): The total height of the stairs. Only used if no baseline is defined, or if the baseline is horizontal. Ignored if ДанныеRiser Height Enforce is non-zero. - ДанныеLength (
Length): The total length of the stairs if no baseline is defined. Ignored if ДанныеTread Depth Enforce is non-zero. - ДанныеWidth (
Length): The width of the stairs. - ДанныеWidth of Landing (
FloatList): If the ДанныеNumber Of Steps is 1, the stairs object acts as a landing. When this is the case and the baseline is multi-segment, the width of the first segment of the landing follows the ДанныеWidth, and the widths of subsequent segments follow the list set here.
Steps (Ступени)
- ДанныеBlondel Ratio (
Float): (только для чтения) Рассчитанный коэффициент Блонделя. Это соотношение позволяет определить наиболее удобную для человека лестницу и должно составлять от 62 до 64 см или от 24,5 до 25,5 дюйма. - ДанныеLanding Depth (
Length): Длина лестничной площадки находящейся по ходу лестницы, указывается только если площадка ДанныеLandings добавлена. По умолчанию значение ДанныеWidth равно 0. - ДанныеNosing (
Length): Размер выступа ступени. - ДанныеNumber Of Steps (
Integer): Количество ступеней (подступенников). - ДанныеRiser Height (
Length): (только для чтения) Высота подступенников лестницы. Если высота ступеней ДанныеRiser Height Enforce равна нулю, тогда она вычисляется как (ДанныеHeight / ДанныеNumber of Steps). В других случаях это значение эквивалентно ДанныеRiser Height Enforce. - ДанныеRiser Height Enforce (
Length): Принудительная высота подступенников лестницы. - ДанныеRiser Thickness (
Length): Толщина подступенников лестницы. - ДанныеTread Depth (
Length): (только для чтения) Длина ступеней. Если ДанныеTread Depth Enforce равно 0, то вычисляется как (ДанныеLength / ДанныеNumber of Steps). В других случаях это значение эквивалентно ДанныеTread Depth Enforce. - ДанныеTread Depth Enforce (
Length): Принудительная длина ступеней - ДанныеTread Thickness (
Length): Толщина ступеней.
Structure
- ДанныеConnection Down Start Stairs (
Enumeration): The type of connection between the lower floor slab and the start of the stairs. Can beHorizontalCut,VerticalCutorHorizontalVerticalCut. - ДанныеConnection End Stairs Up (
Enumeration): The type of connection between the end of the stairs and the upper floor slab. Can betoFlightThicknessortoSlabThickness. - ДанныеDown Slab Thickness (
Length): The thickness of the lower floor slab. - ДанныеFlight (
Enumeration): The direction of the flight after the landing. Can beStraight,HalfTurnLeftorHalfTurnRight. The ДанныеLandings property must be set toAt center. - ДанныеLandings (
Enumeration): The type of landings. Can beNoneorAt center(At each cornernot implemented yet). - ДанныеStringer Overlap (
Length): The overlap of the stringers above the bottom of the treads. - ДанныеStringer Width (
Length): The width of the stringers. - ДанныеStructure (
Enumeration): The structure type of the stairs. Can beNone,Massive,One stringerorTwo stringers. For the last two options, the ДанныеStringer Width and ДанныеTread Thickness properties must have non-zero values. - ДанныеStructure Offset (
Length): The offset between the border of the stairs and the structure. - ДанныеStructure Thickness (
Length): The thickness of the structure. - ДанныеUp Slab Thickness (
Length): The thickness of the upper floor slab. - Данные (Hidden)Winders (
Enumeration): The type of winders. Not implemented.
Ограничения
- На данный момент доступны только прямые лестницы
- См. тему на форуме про круговые лестницы.
- См. уведомления о данном инструменте на форуме.
Программирование
См. так же: Arch API и Основы составления скриптов в FreeCAD.
Stairs = makeStairs(baseobj=None, length=None, width=None, height=None, steps=None, name="Stairs")
- Creates a
Stairsobject from the givenbaseobj. - If
baseobjis not given, it will uselength,width,height, andsteps, to build a solid object.
Пример:
import Arch
Stairs = Arch.makeStairs(length=5000, width=1200, height=3000, steps=14)
- 2D drafting: Sketch, Line, Polyline, Circle, Arc, Arc From 3 Points, Fillet, Ellipse, Polygon, Rectangle, B-Spline, Bézier Curve, Cubic Bézier Curve, Point
- 3D/BIM: Project, Site, Building, Level, Space, Wall, Curtain Wall, Column, Beam, Slab, Door, Window, Pipe, Connector, Stairs, Roof, Panel, Frame, Fence, Truss, Equipment
- Reinforcement Tools: Custom Rebar, Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement
- Generic 3D Tools: Profile, Box, Shape Builder, Facebinder, Objects Library, Component, External Reference
- Annotation: Text, Shape From Text, Aligned Dimension, Horizontal Dimension, Vertical Dimension, Leader, Label, Hatch, Axis, Axis System, Grid, Section Plane, New Page, New View
- Create 2D Views: 2D Drawing, Section View, Section Cut
- Snapping: Snap Lock, Snap Endpoint, Snap Midpoint, Snap Center, Snap Angle, Snap Intersection, Snap Perpendicular, Snap Extension, Snap Parallel, Snap Special, Snap Near, Snap Ortho, Snap Grid, Snap Working Plane, Snap Dimensions, Toggle Grid, Working Plane Front, Working Plane Top, Working Plane Side, Working Plane
- Modify: Move, Copy, Rotate, Clone, Create Simple Copy, Create Compound, Offset, 2D Offset, Trimex, Join, Split, Scale, Stretch, Draft to Sketch, Upgrade, Downgrade, Add Component, Remove Component, Array, Path Array, Polar Array, Point Array, Cut With Plane, Mirror, Extrude, Difference, Union, Intersection
- Manage: BIM Setup, Views Manager, Setup Project, Manage Doors and Windows, Manage IFC Elements, Manage IFC Quantities, Manage IFC Properties, Manage Classification, Manage Layers, Material, Schedule, Preflight Checks, Annotation Styles
- Utils: Toggle Bottom Panels, Move to Trash, Working Plane View, Select Group, Set Slope, Working Plane Proxy, Add to Construction Group, Split Mesh, Mesh to Shape, Select Non-Manifold Meshes, Remove Shape From BIM, Close Holes, Merge Walls, Check, Toggle IFC B-Rep Flag, Toggle Subcomponents, Survey, IFC Diff, IFC Explorer, New IFC Spreadsheet, Image Plane, Unclone, Rewire, Glue, Re-Extrude
- Panel Tools: Panel, Panel Cut, Panel Sheet, Nest
- Structure Tools: Structure, Structural System, Multiple Structures
- IFC Tools: IFC Diff, IFC Expand, Create IFC Project, IfcOpenShell Update
- Nudge: Nudge Switch, Nudge Up, Nudge Down, Nudge Left, Nudge Right, Nudge Rotate Left, Nudge Rotate Right, Nudge Extend, Nudge Shrink
- Additional: Preferences, Fine tuning, Import Export Preferences, IFC, DAE, OBJ, JSON, 3DS, SHP
- Начинающим
- Установка: Загрузка, Windows, Linux, Mac, Дополнительных компонентов, Docker, AppImage, Ubuntu Snap
- Базовая: О FreeCAD, Интерфейс, Навигация мыши, Методы выделения, Имя объекта, Настройки, Верстаки, Структура документа, Свойства, Помоги FreeCAD, Пожертвования
- Помощь: Учебники, Видео учебники
- Верстаки: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
