Reinforcement SlabRebars/it: Difference between revisions
No edit summary |
(Created page with "7. Ora impostare i dati desiderati nei dati di input per l'armatura nella direzione trasversale della faccia selezionata come mostrato nell'immagine sottostante.") |
||
Line 58: | Line 58: | ||
6. Ora cliccare sul pulsante {{Button|Next}} o selezionare Cross Rebars nella visualizzazione elenco. |
6. Ora cliccare sul pulsante {{Button|Next}} o selezionare Cross Rebars nella visualizzazione elenco. |
||
7. Ora impostare i dati desiderati nei dati di input per l'armatura nella direzione trasversale della faccia selezionata come mostrato nell'immagine sottostante. |
|||
7. Now select desired data for input data for rabars in cross direction of selected face as show in below image. |
|||
[[File:Bent_Shape_rebars_in_cross_direction_with_distribution_rebars.png]] |
[[File:Bent_Shape_rebars_in_cross_direction_with_distribution_rebars.png]] |
Revision as of 15:12, 15 October 2023
Armatura di soletta |
Posizione nel menu |
---|
Arch → Strumenti di armatura → Armatura soletta 3D/BIM → Reinforcement tools → Armatura soletta |
Ambiente |
Arch |
Avvio veloce |
Nessuno |
Introdotto nella versione |
- |
Vedere anche |
Ambiente Rinforzi, Armatura, Armatura elicoidale |
Descrizione
Lo strumento Armatura di soletta consente all'utente di creare barre d'armatura all'interno di un oggetto Struttura soletta.
Questo comando fa parte dell'Ambiente Rinforzi, un Ambiente complementare che può essere installato con l' Addon Manager tramite il menu Strumenti → Addon manager → Reinforcement.
Un esempio di armatura all'interno di una Struttura soletta
Vista da destra dell'esempio di armatura della soletta
Vista frontale dell'esempio di armatura della soletta
Utilizzo
1. Selezionare una faccia qualsiasi di un oggetto Struttura Soletta creato in precedenza. come mostrato nell'immagine qui sotto.
Faccia selezionata per la struttura soletta
2. Quindi selezionare Armatura soletta dagli strumenti dell'armatura.
3. Sullo schermo verrà visualizzata una finestra di dialogo come mostrato di seguito.
Finestra di dialogo per l'armatura di soletta
4. Selezionare il tipo di copertura desiderata per la rete di rinforzo (Superiore o Inferiore).
5. Selezionare il tipo di armatura desiderata e altri dati di input per le armature nella direzione parallela della faccia selezionata, come mostrato nell'immagine sottostante.
Finestra di dialogo per le armature della soletta in direzione parallela alla faccia selezionata
6. Ora cliccare sul pulsante Next o selezionare Cross Rebars nella visualizzazione elenco.
7. Ora impostare i dati desiderati nei dati di input per l'armatura nella direzione trasversale della faccia selezionata come mostrato nell'immagine sottostante.
Dialog Box for Slab Reinforcement of the Rebars in cross direction of selected face
8. Click OK or Apply or Finish to generate Slab reinforcement.
9. Click Cancel to exit the dialog box.
Proprietà
Properties for Rebars in Parallel Direction to selected face:
- DatiMesh Cover Along: It represent alignment of rebar mesh along top or bottom face of structure. It can have two values "Top" and "Bottom".
- DatiRebar Type: Type of rebar for parallel rebars for slab reinforcement. It can have four values 'StraightRebar', 'LShapeRebar', 'UShapeRebar', 'BentShapeRebar'.
- DatiFront Cover: The distance between parallel rebar and selected face.
- DatiLeft Cover: The distance between the left end of the parallel rebar to the left face of the structure.
- DatiRight Cover: The distance between the right end of the parallel rebar to right face of the structure.
- DatiBottom Cover: The distance between parallel rebars from the bottom face of the structure.
- DatiTop Cover: The distance between parallel rebars from the top face of the structure.
- DatiRear Cover: Rear cover for slab reinforcement of parallel rebars.
- DatiAnchor Length: It represents arm's length of bent shape parallel rebar when parallel rebar type is BentShapeRebar.
- DatiBent Angle: It represents angle for bent shape parallel rebar when parallel rebar type is BentShapeRebar.
- DatiRounding: A rounding value to be applied to the corners of the bars, expressed in times of diameter of parallel rebars.
- DatiDiameter: Diameter of parallel rebars
- DatiAmount: It contains count of parallel rebars.
- DatiSpacing: It contains spacing between parallel rebars.
Properties of Distribution Rebars for bent shape rebars in parallel Direction to selected face:
- DatiAmount: It contains count of Distribution Rebars for Bent shape rebars in parallel Direction.
- DatiSpacing: It contains spacing between Distribution Rebars for Bent shape rebars in parallel Direction.
Properties for Rebars in Cross Direction to selected face:
- DatiRebar Type: Type of rebar for cross rebars for slab reinforcement. It can have four values 'StraightRebar', 'LShapeRebar', 'UShapeRebar', 'BentShapeRebar'.
- DatiFront Cover: The distance between cross rebar and selected face.
- DatiLeft Cover: The distance between the left end of the cross rebar to the left face of the structure.
- DatiRight Cover: The distance between the right end of the cross rebar to right face of the structure.
- DatiBottom Cover: The distance between cross rebars from the bottom face of the structure.
- DatiTop Cover: The distance between cross rebars from the top face of the structure.
- DatiRear Cover: Rear cover for slab reinforcement of cross rebars.
- DatiAnchor Length: It represents arm's length of bent shape cross rebar when cross rebar type is BentShapeRebar.
- DatiBent Angle: It represents angle for bent shape cross rebar when cross rebar type is BentShapeRebar.
- DatiRounding: A rounding value to be applied to the corners of the bars, expressed in times of diameter of cross rebars.
- DatiDiameter: Diameter of cross rebars
- DatiAmount: It contains count of cross rebars.
- DatiSpacing: It contains spacing between cross rebars.
Properties of Distribution Rebars for bent shape rebars in cross Direction to selected face:
- DatiAmount: It contains count of Distribution Rebars for Bent shape rebars in cross Direction.
- DatiSpacing: It contains spacing between Distribution Rebars for Bent shape rebars in cross Direction.
Script
See also: Arch API, Reinforcement API and FreeCAD Scripting Basics.
The Slab Reinforcement tool can be used from the Python console by using the following function:
Create Slab Reinforcement
from SlabReinforcement.SlabReinforcement import makeSlabReinforcement
SlabReinforcementGroup = makeSlabReinforcement(
parallel_rebar_type,
parallel_front_cover,
parallel_rear_cover,
parallel_left_cover,
parallel_right_cover,
parallel_top_cover,
parallel_bottom_cover,
parallel_diameter,
parallel_amount_spacing_check,
parallel_amount_spacing_value,
cross_rebar_type,
cross_front_cover,
cross_rear_cover,
cross_left_cover,
cross_right_cover,
cross_top_cover,
cross_bottom_cover,
cross_diameter,
cross_amount_spacing_check,
cross_amount_spacing_value,
cross_rounding = 2,
cross_bent_bar_length = 50,
cross_bent_bar_angle = 135,
cross_l_shape_hook_orintation = "Alternate",
cross_distribution_rebars_check = False,
cross_distribution_rebars_diameter = 8,
cross_distribution_rebars_amount_spacing_check = True,
cross_distribution_rebars_amount_spacing_value = 2,
parallel_rounding = 2,
parallel_bent_bar_length = 50,
parallel_bent_bar_angle = 135,
parallel_l_shape_hook_orintation = "Alternate",
parallel_distribution_rebars_check = False,
parallel_distribution_rebars_diameter = 8,
parallel_distribution_rebars_amount_spacing_check = True,
parallel_distribution_rebars_amount_spacing_value = 2,
mesh_cover_along = "Bottom",
structure = None,
facename = None,
)
- Creates a
SlabReinforcementGroup
object from the givenstructure
, which is a Slab Arch Structure, andfacename
, which is a face of that structure.- If no
structure
norfacename
are given, it will take the user selected face as input.
- If no
Properties for Rebars in Parallel Direction to selected face:
- Datiparallel_rebar_type: Type of rebar for parallel rebars for slab reinforcement. It can have four values 'StraightRebar', 'LShapeRebar', 'UShapeRebar', 'BentShapeRebar'.
- Datiparallel_front_cover: The distance between parallel rebar and selected face.
- Datiparallel_rear_cover: Rear cover for slab reinforcement of parallel rebars.
- Datiparallel_left_cover: The distance between the left end of the parallel rebar to the left face of the structure.
- Datiparallel_right_cover: The distance between the right end of the parallel rebar to right face of the structure.
- Datiparallel_top_cover: The distance between parallel rebars from the top face of the structure.
- Datiparallel_bottom_cover: The distance between parallel rebars from the bottom face of the structure.
- Datiparallel_diameter: Diameter of parallel rebars.
- Datiparallel_amount_spacing_check: If is set to True, then value of parallel_amount_spacing_value is used as rebars count else parallel_amount_spacing_value's value is used as spacing in parallel rebars.
- Datiparallel_amount_spacing_value: It contains count of rebars or spacing between parallel rebars based on value of amount_spacing_check.
- Datiparallel_rounding: A rounding value to be applied to the corners of the bars, expressed in times the parallel_diameter.
- Datiparallel_bent_bar_length: It represents arm's length of bent shape parallel rebar when parallel_rebar_type is BentShapeRebar
- Datiparallel_bent_bar_angle: It represents angle for bent shape parallel rebar when parallel_rebar_type is BentShapeRebar
- Datiparallel_l_shape_hook_orintation: It represents orintation of hook of parallel L-Shape rebar if parallel_rebar_type is LShapeRebar. It can have three values "Left", "Right","Alternate"
- Datiparallel_distribution_rebars_check: If True add distribution rebars for parallel bent shape rebars. Default is False.
- Datiparallel_distribution_rebars_diameter: Diameter of distribution rebars for parallel bent shape rebars.
- Datiparallel_distribution_rebars_amount_spacing_check: If is set to True, then value of parallel_distribution_rebars_amount_spacing_value is used as rebars count else parallel_distribution_rebars_amount_spacing_value's value is used as spacing in parallel_distribution_rebars. Default is True.
- Datiparallel_distribution_rebars_amount_spacing_value: It contains count or spacing between distribution rebars for one side of parallel bent shape rebars based on value of parallel_distribution_rebars_check. Default is 2.
Properties for Rebars in Cross Direction to selected face:
- Daticross_rebar_type: Type of rebar for cross rebars for slab reinforcement. It can have four values 'StraightRebar', 'LShapeRebar', 'UShapeRebar', 'BentShapeRebar'.
- Daticross_front_cover: The distance between cross rebar and cross_face (face perpendicular to selected face).
- Daticross_rear_cover: Rear cover for slab reinforcement of cross rebars.
- Daticross_left_cover: The distance between the left end of the cross rebar to the left face of the structure.
- Daticross_right_cover: The distance between the right end of the rebar to right face of the structure relative to cross_face.
- Daticross_top_cover: The distance between cross rebar from the top face of the structure.
- Daticross_bottom_cover: The distance between cross rebar from the bottom face of the structure.
- Daticross_diameter: Diameter of cross rebars.
- Daticross_amount_spacing_check: If is set to True, then value of cross_amount_spacing_value is used as rebars count else cross_amount_spacing_value's value is used as spacing in rebars.
- Daticross_amount_spacing_value: It contains count of rebars or spacing between rebars based on value of cross_amount_spacing_check.
- Daticross_rounding: A rounding value to be applied to the corners of the bars, expressed in times the cross_diameter.
- Daticross_bent_bar_length: It represents arm's length of bent shape cross rebar when cross_rebar_type is BentShapeRebar
- Daticross_bent_bar_angle: It represents angle for bent shape cross rebar when cross_rebar_type is BentShapeRebar
- Daticross_l_shape_hook_orintation: It represents orintation of hook of cross L-Shape rebar if cross_rebar_type is LShapeRebar. It can have three values "Left", "Right", "Alternate"
- Daticross_distribution_rebars_check: If True add distribution rebars for cross bent shape rebars. Default is False.
- Daticross_distribution_rebars_diameter: Diameter for distribution rebars for cross bent shape rebars.
- Daticross_distribution_rebars_amount_spacing_check: If is set to True, then value of cross_distribution_rebars_amount_spacing_value is used as rebars count else cross_distribution_rebars_amount_spacing_value's value is used as spacing in cross_distribution_rebars. Default is True.
- Daticross_distribution_rebars_amount_spacing_value: It contains count or spacing between distribution rebars for one side of cross bent shape rebars based on value of cross_distribution_rebars_check. Default is 2.
Common Properties for Parallel and Cross Rebars:
- Datimesh_cover_along: It can have two values "Top" and "Bottom". It represent alignment of rebar mesh along top or bottom face of structure.
- Datistructure: Arch structure object. Default is None
- Datifacename: selected face of structure. Default is None
Edition of Slab Reinforcement
You can change the properties of the Slab Reinforcement with the following function
from SlabReinforcement.SlabReinforcement import editSlabReinforcement
slabReinforcementGroup = editSlabReinforcement(
slabReinforcementGroup,
parallel_rebar_type,
parallel_front_cover,
parallel_rear_cover,
parallel_left_cover,
parallel_right_cover,
parallel_top_cover,
parallel_bottom_cover,
parallel_diameter,
parallel_amount_spacing_check,
parallel_amount_spacing_value,
cross_rebar_type,
cross_front_cover,
cross_rear_cover,
cross_left_cover,
cross_right_cover,
cross_top_cover,
cross_bottom_cover,
cross_diameter,
cross_amount_spacing_check,
cross_amount_spacing_value,
cross_rounding = 2,
cross_bent_bar_length = 50,
cross_bent_bar_angle = 135,
cross_l_shape_hook_orintation = "Alternate",
cross_distribution_rebars_check = False,
cross_distribution_rebars_diameter = 8,
cross_distribution_rebars_amount_spacing_check = True,
cross_distribution_rebars_amount_spacing_value = 2,
parallel_rounding = 2,
parallel_bent_bar_length = 50,
parallel_bent_bar_angle = 135,
parallel_l_shape_hook_orintation = "Alternate",
parallel_distribution_rebars_check = False,
parallel_distribution_rebars_diameter = 8,
parallel_distribution_rebars_amount_spacing_check = True,
parallel_distribution_rebars_amount_spacing_value = 2,
mesh_cover_along: str = "Bottom",
structure = None,
facename = None,
)
slabReinforcementGroup
is a previously createdSlab Reinforcement
group object.- The other parameters are the same as required by the
makeSlabReinforcement()
function.
Examples for Slab Reinforcement
- Elements: Wall, Structure, Curtain Wall, Window, Roof, Space, Stairs, Equipment, Frame, Fence, Truss, Profile, Pipe, Pipe Connector
- Reinforcements: Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement, Custom Rebar
- Panels: Panel, Panel Cut, Panel Sheet, Nest
- Materials: Material, Multi-Material
- Organization: Building Part, Project, Site, Building, Level, External reference, Section Plane, Schedule
- Axes: Axis, Axes system, Grid
- Modification: Cut with plane, Add component, Remove component, Survey
- Utilities: Component, Clone component, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, 3 Views from mesh, Create IFC spreadsheet, Toggle Subcomponents
- Additional: Preferences, Import Export Preferences (IFC, DAE, OBJ, JSON, 3DS, SHP), IfcOpenShell, IfcPlusPlus, Arch API
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub