Arch: Armatura di trave
|
Posizione nel menu |
---|
Arch → Strumenti armatura → Armatura di trave o 3D/BIM → Reinforcement → Beam Reinforcement |
Ambiente |
Reinforcement, Arch, BIM |
Avvio veloce |
Nessuno |
Introdotto nella versione |
0.19 |
Vedere anche |
Armatura di pilastro con due staffe e sei barre, Armatura |
Descrizione
Lo strumento Rinforzo di trave consente all'utente di creare delle barre di rinforzo all'interno di un oggetto Struttura Trave.
The Beam Reinforcement tool is also integrated into BIM Workbench.
Questo comando fa parte dell'ambiente aggiuntivo Reinforcement, che si può installare con Addon manager, tramite il menu Strumenti → Addon manager → Reinforcement.
Rinforzo di trave all'interno di una Struttura trave
Utilizzo
1. Seleziona la faccia destra di un oggetto Struttura trave precedentemente creata, avente la lunghezza sull'asse x. Oppure seleziona la faccia anteriore di un oggetto
Struttura trave precedentemente creata, avente la lunghezza sull'asse y.
2. Quindi selezionare Rinforzo di trave dagli Strumenti armatura.
3. Appare una finestra di dialogo come quella mostrata sotto.
Finestra di dialogo per lo strumento Rinforzo di trave
4. Selezionare il tipo desiderato di rinforzo di trave.
5. Fornire gli input per i dati relativi alle staffe.
6. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.
Finestra di dialogo per i dati della parte superiore dell'armatura
7. Impostare i dati per le armature superiori.
- Per editare i valori Number#Diameter@Offset, fare clic sul pulsante Modifica accanto all'etichetta Number#Diameter@Offset. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore di Rebar Type, fare clic sul pulsante Modifica accanto all'etichetta Rebar Type. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore di Orientamento gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Orientation. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore dell'estensione del gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Extension. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore dell'arrotondamento della barra, fare clic sul pulsante Modifica accanto all'etichetta Rounding. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore di spaziatura dei livelli, fare clic sul pulsante Modifica accanto all'etichetta Layer Spacing. Appare una finestra di dialogo come mostrato di seguito.
8. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.
Finestra di dialogo per i dati della parte inferiore dell'armatura
9. Impostare i dati per le armature inferiori in modo simile ai dati delle armature superiori.
10. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.
Definire i dati per le barre di rinforzo sul lato sinistro.
11. Impostare i dati per le armature di taglio a sinistra.
- Per editare i valori Number#Diameter@Offset, fare clic sul pulsante Modifica accanto all'etichetta Number#Diameter@Offset. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore di Rebar Type, fare clic sul pulsante Modifica accanto all'etichetta Rebar Type. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore di Orientamento gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Orientation. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore dell'estensione del gancio, fare clic sul pulsante Modifica accanto all'etichetta Hook Extension. Appare una finestra di dialogo come mostrato di seguito.
- Per modificare il valore dell'arrotondamento della barra, fare clic sul pulsante Modifica accanto all'etichetta Rounding. Appare una finestra di dialogo come mostrato di seguito.
12. Fare clic su Avanti e la finestra di dialogo viene aggiornata come mostrato di seguito.
Definire i dati per le barre di rinforzo sul lato destro.
13. Impostare i dati per le armature di taglio a destra in modo simile ai dati delle armature di taglio a sinistra.
14. Cliccare su OK o su Applica per generare l'armatura.
15. Cliccare Cancella per uscire dalla finestra di dialogo.
Proprietà
Stirrups:
- DatiLeft Cover: a distanza tra l'estremità sinistra della staffa e la faccia sinistra della struttura - copriferro a sinistra.
- DatiRight Cover: la distanza tra l'estremità destra della staffa e la faccia destra della struttura - copriferro a destra.
- DatiTop Cover: la distanza tra la staffa e la faccia superiore della struttura.
- DatiBottom Cover: la distanza tra la staffa e la faccia inferiore della struttura.
- DatiOffset: la distanza tra la staffa e la faccia superiore e inferiore della struttura.
- DatiDiameter: diametro della staffa.
- DatiBent Angle: l'angolo dipiega definisce l'angolo alle estremità di una staffa.
- DatiExtension Factor: il fattore di estensione definisce la lunghezza dell'estremità della staffa, espressa in volte il diametro.
- DatiNumber: il numero di staffe.
- DatiSpacing: la distanza tra gli assi di ogni staffa.
Top/Bottom Reinforcement Rebars: barre di armatura presenti nella parte superiore e inferiore della trave
- DatiNumberDiameterOffset: Una tupla della stringa Number#Diameter@Offset. Ogni elemento della tupla rappresenta il rinforzo per ogni nuovo livello.
- DatiRebar Type: Elenco di tuple del tipo di barre di rinforzo.
- DatiHook Orientation: Elenco di tuple di orientamento dei ganci a forma di L.
- DatiHook Extension: Elenco di tuple di lunghezza del gancio a forma di L delle armature.
- DatiRounding: Elenco di tuple del valore di arrotondamento da applicare agli angoli delle armature a forma di L, espresse in volte il diametro.
- DatiLayer Spacing: Elenco di spaziatura tra due strati di rinforzo consecutivi.
Left/Right Reinforcement Rebars: barre di armatura presenti nella parte sinistra e destra della trave
- DatiNumberDiameterOffset: Stringa di Number#Diameter@Offset per barre di rinforzo..
- DatiRebar Type: Elenco dei tipi di barre di rinforzo.
- DatiHook Orientation: Lista per l'orientamento dei ganci a forma di L..
- DatiHook Extension: Lista per la lunghezza del gancio a forma di L delle armature.
- DatiRounding: Lista per il valore di arrotondamento da applicare agli angoli delle armature a forma di L, espresse in volte il diametro.
- DatiRebar Spacing: Elenco di spaziatura tra due strati di rinforzo consecutivi.
Script
Vedere anche: API Arch, API di Reinforcement e Basi di script per FreeCAD.
Lo strumento Rinforzo di trave può essere utilizzato nelle macro e dalla console Python utilizzando la seguente funzione:
Creare staffe con due ganci
RebarGroup = makeReinforcement(
l_cover_of_stirrup,
r_cover_of_stirrup,
t_cover_of_stirrup,
b_cover_of_stirrup,
offset_of_stirrup,
bent_angle,
extension_factor,
dia_of_stirrup,
number_spacing_check,
number_spacing_value,
top_reinforcement_number_diameter_offset,
top_reinforcement_rebar_type,
top_reinforcement_layer_spacing,
bottom_reinforcement_number_diameter_offset,
bottom_reinforcement_rebar_type,
bottom_reinforcement_layer_spacing,
left_rebars_number_diameter_offset,
left_rebars_type,
left_rebars_spacing,
right_rebars_number_diameter_offset,
right_rebars_type,
right_rebars_spacing,
top_reinforcement_l_rebar_rounding=2,
top_reinforcement_hook_extension=40,
top_reinforcement_hook_orientation="Front Inside",
bottom_reinforcement_l_rebar_rounding=2,
bottom_reinforcement_hook_extension=40,
bottom_reinforcement_hook_orientation="Front Inside",
left_l_rebar_rounding=2,
left_rebars_hook_extension=40,
left_rebars_hook_orientation="Front Inside",
right_l_rebar_rounding=2,
right_rebars_hook_extension=40,
right_rebars_hook_orientation="Front Inside",
structure=None,
facename=None,
)
- Creates a
RebarGroup
object from the givenstructure
, which is an Arch Structure, andfacename
, which is a face of that structure.- If no
structure
norfacename
are given, it will take the user selected face as input.
- If no
l_cover_of_stirrup
,r_cover_of_stirrup
,t_cover_of_stirrup
,b_cover_of_stirrup
andoffset_of_stirrup
are inner offset distances for the stirrup elements with respect to the faces of the structure. They are respectively the left, right, top, bottom and front/rear offsets.bent_angle
define the angle of the tip of the reinforcement loop of stirrup.extension_factor
define the length of the tip of the reinforcement loop of stirrup, expressed in times the diameter.dia_of_stirrup
is the diameter of the stirrup.number_spacing_check
if it isTrue
it will create as many stirrup as given bynumber_spacing_value
; if it isFalse
it will create stirrup separated by the numerical value ofnumber_spacing_value
.number_spacing_value
specifies the number of stirrups, or the value of the separation between them, depending onnumber_spacing_check
.top_reinforcement_number_diameter_offset
andbottom_reinforcement_number_diameter_offset
are tuple of number_diameter_offset string. Each element of tuple represents reinforcement for each new layer.
Syntax: ( "number1#diameter1@offset1+number2#diameter2@offset2+...", "number3#diameter3@offset3+number4#diameter4@offset4+...", ..., )
top_reinforcement_rebar_type
andbottom_reinforcement_rebar_type
specifies type of top/bottom reinforcement bars.
Possible values: 1. 'StraightRebar' or 'LShapeRebar' 2. ('<rebar_type>', '<rebar_type>', ...) and number of elements of tuple must be equal to number of reinforcement layers. 3. [ ('<rebar_type>', '<rebar_type>', ...), ('<rebar_type>', '<rebar_type>', ...), ..., ] each element of list is a tuple, which specifies rebar type of each reinforcement layer. And each element of tuple represents rabar_type for each set of rebars. 4. [ <rebar_type>, ('<rebar_type>', '<rebar_type>', ...), ..., ]
top_reinforcement_layer_spacing
andbottom_reinforcement_layer_spacing
is the spacing between two consecutive reinforcement layers.
Possible values: 1. <layer_spacing> 2. (<spacing in layer1 and layer2>, <spacing in layer2 and layer3>, ...) and number of elements of tuple must be equal to one less than number of layers.
left_rebars_number_diameter_offset
andright_rebars_number_diameter_offset
are string of number_diameter_offset.
Syntax: "number1#diameter1@offset1+number2#diameter2@offset2+..."
left_rebars_type
andright_rebars_type
specifies type of left/right reinforcement bars.
Possible values: 1. 'StraightRebar' or 'LShapeRebar' 2. ('<rebar_type>', '<rebar_type>', ...) and each element of tuple represents rabar_type for each set of rebars.
left_rebars_spacing
andright_rebars_spacing
is clear spacing between consecutive reinforcement bars.top_reinforcement_l_rebar_rounding
andbottom_reinforcement_l_rebar_rounding
is the parameter that determines the bending radius of the LShaped top/bottom rebars, expressed as times the diameter. Possible syntax are similar to as discussed above fortop_reinforcement_rebar_type
/bottom_reinforcement_rebar_type
.top_reinforcement_hook_extension
andbottom_reinforcement_hook_extension
is the length of hook of LShaped rebars. Possible syntax are similar to as discussed above fortop_reinforcement_rebar_type
/bottom_reinforcement_rebar_type
.top_reinforcement_hook_orientation
andbottom_reinforcement_hook_orientation
specifies the orientation of LShaped hook; it can be"Front Inside"
,"Front Outside"
,"Rear Inside"
or"Rear Outside"
. Possible syntax are similar to as discussed above fortop_reinforcement_rebar_type
/bottom_reinforcement_rebar_type
.left_l_rebar_rounding
andright_l_rebar_rounding
is the parameter that determines the bending radius of the LShaped left/right rebars, expressed as times the diameter. Possible syntax are similar to as discussed above forleft_rebars_type
/right_rebars_type
.left_rebars_hook_extension
andright_rebars_hook_extension
is the length of hook of LShaped rebars. Possible syntax are similar to as discussed above forleft_rebars_type
/right_rebars_type
.left_rebars_hook_orientation
andright_rebars_hook_orientation
specifies the orientation of LShaped hook; it can be"Front Inside"
,"Front Outside"
,"Rear Inside"
or"Rear Outside"
. Possible syntax are similar to as discussed above forleft_rebars_type
/right_rebars_type
.
Esempio
import FreeCAD, Arch
from BeamReinforcement import TwoLeggedBeam
Structure = Arch.makeStructure(length=3000.0,width=200.0,height=400.0)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
RebarGroup = TwoLeggedBeam.makeReinforcement(
l_cover_of_stirrup=20,
r_cover_of_stirrup=20,
t_cover_of_stirrup=20,
b_cover_of_stirrup=20,
offset_of_stirrup=100,
bent_angle=135,
extension_factor=4,
dia_of_stirrup=8,
number_spacing_check=False,
number_spacing_value=200,
top_reinforcement_number_diameter_offset=("1#20@-60+2#16@-60+1#20@-60", "3#16@-100"),
top_reinforcement_rebar_type="LShapeRebar",
top_reinforcement_layer_spacing=30,
bottom_reinforcement_number_diameter_offset=("1#20@-60+2#16@-60+1#20@-60", "3#16@-100"),
bottom_reinforcement_rebar_type="LShapeRebar",
bottom_reinforcement_layer_spacing=30,
left_rebars_number_diameter_offset="1#16@-100+1#16@-100+1#16@-100",
left_rebars_type="LShapeRebar",
left_rebars_spacing=30,
right_rebars_number_diameter_offset="1#16@-100+1#16@-100+1#16@-100",
right_rebars_type="LShapeRebar",
right_rebars_spacing=30,
top_reinforcement_l_rebar_rounding=2,
top_reinforcement_hook_extension=100,
top_reinforcement_hook_orientation="Rear Outside",
bottom_reinforcement_l_rebar_rounding=2,
bottom_reinforcement_hook_extension=100,
bottom_reinforcement_hook_orientation="Rear Outside",
left_l_rebar_rounding=2,
left_rebars_hook_extension=80,
left_rebars_hook_orientation=("Rear Inside", "Front Inside", "Rear Inside"),
right_l_rebar_rounding=2,
right_rebars_hook_extension=80,
right_rebars_hook_orientation=("Front Inside", "Rear Inside", "Front Inside"),
structure=Structure,
facename="Face6",
)
- Elements: Wall, Structure, Curtain Wall, Window, Roof, Space, Stairs, Equipment, Frame, Fence, Truss, Profile, Pipe, Pipe Connector
- Reinforcements: Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement, Custom Rebar
- Panels: Panel, Panel Cut, Panel Sheet, Nest
- Materials: Material, Multi-Material
- Organization: Building Part, Project, Site, Building, Level, External reference, Section Plane, Schedule
- Axes: Axis, Axes system, Grid
- Modification: Cut with plane, Cut with line, Add component, Remove component, Survey
- Utilities: Component, Clone component, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, 3 Views from mesh, Create IFC spreadsheet, Toggle Subcomponents
- Additional: Preferences, Import Export Preferences (IFC, DAE, OBJ, JSON, 3DS, SHP), IfcOpenShell, IfcPlusPlus, Arch API

- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Path, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web
- Hubs: User hub, Power users hub, Developer hub