FEM RandbedingungVerbinder

From FreeCAD Documentation
Revision as of 10:12, 16 February 2024 by FuzzyBot (talk | contribs) (Updating to match new version of source page)

FEM RandbedingungVerbinder

Menüeintrag
Modell → Mechanische Randbedingungen und Belastungen → Randbedingung Verbinder
Arbeitsbereich
FEM
Standardtastenkürzel
Keiner
Eingeführt in Version
0.19
Siehe auch
FEM RandbedingungDruck

Beschreibung

Legt eine Randbedingung Verbinder fest, die zwei ausgewählte Flächen in einer Weise verbindet, dass sie (anders als ein Kontakt funktioniert) während der Analyse nicht getrennt werden können und nicht aufeinander gleiten können. So bleiben die Flächen dauerhaft untrennbar verbunden.

Anwendung

  1. Es gibt mehrere Möglichkeiten den Befehl aufzurufen:
    • Die Schaltfläche Randbedingung Verbinder drücken.
    • Den Menüeintrag Modell → Mechanische Randbedingungen und Belastungen → Randbedingung Verbinder auswählen.
  2. Die Schaltfläche Hinzufügen im Aufgaben-Bereich drücken und dann die Fläche anklicken, die der Randbedingung Verbinder zugeordnet werden soll. Nacheinander genau zwei Flächen auswählen. Die zuerst ausgewählte Fläche ist die untergeordnete Fläche, während die zweite die Hauptfläche ist.
  3. Wahlweise die Toleranz festlegen - Die Randbedingung Verbinder wird nur auf Knoten der untergeordneten Fläche angewendet, die zur Hauptfläche einen Abstand haben, der nicht größer ist, als der hier angegebene.
  4. eingeführt mit Version 0.22: Wahlweise die Checkbox Enable Adjust aktivieren, um den Knoten der untergeordneten Fläche zu erlauben, automatisch bewegt und auf die Hauptfläche gelegt zu werden, wenn sie von der Randbedingung betroffen sind (d.h. dass sie dem Toleranzkriterium entsprechen).

Cyclic symmetry

introduced in version 0.22: Tie constraint can also be used to define cyclic symmetry. This allows the models exhibiting rotational periodic symmetry (repetitive circular patterns around a symmetry axis) to be analyzed using just a single representative sector. It can be particularly useful for rotors, shafts, turbines, fans, flywheels and similar parts, often in combination with centrifugal load. Cyclic symmetry can be defined by selecting the two faces of the cut for tie constraint and setting the following properties:

  • DatenCyclic Symmetry: setting to true activates cyclic symmetry
  • DatenSectors: total number of sectors, equal to 360° divided by the angle of the representative sector (e.g. 8 for 45° sector or 6 for 60° sector)
  • DatenConnected Sectors: number of sectors displayed in results, set it to the same number as DatenSectors if you want to visualize the whole 360° part
  • DatenSymmetry Axis - axis of cyclic symmetry - global Z axis by default, can be moved by applying the Placement transformation to the Z versor (similar to what can be done with Part Lines - to understand how to move the symmetry axis, it might in fact be helpful to change the Placement of Part Line which is usually needed for centrifugal load anyway).

One important limitation of this feature in FEM is that boundary conditions can't be applied to the nodes of the slave surface of cyclic symmetry (slave surface in tie constraint definition) since that would cause an overconstraint. So in some cases, it might be necessary to remove the nodes lying on the edge between the face with the boundary condition and the slave surface of cyclic symmetry from the boundary condition definition. Unfortunately, FreeCAD doesn't operate on node sets and individual nodes can't be deselected so one would have to use workarounds like adding a narrow face partition as a transition between the slave surface and the surface with the boundary condition.

Hinweise