Sketcher CreateArcOfEllipse/ru: Difference between revisions
(Created page with "==Как использовать==") |
(Created page with "* Нажмите кнопку {{KEY|24px '''Дуга по эллипсу'''}}. * Первым нажатием в 3D виде зада...") |
||
Line 23: | Line 23: | ||
==Как использовать== |
==Как использовать== |
||
* |
* Нажмите кнопку {{KEY|[[File:Sketcher CreateArcOfEllipse.png|24px]] '''Дуга по эллипсу'''}}. |
||
* Первым нажатием в 3D виде задайте точку центра эллипса. Вторым нажатием задайте первый радиус и ориентацию эллипса. Третьим нажатием задайте другой радиус и начало дуги. Четвертым нажатием задайте конец дуги. |
|||
* First click in 3D view sets ellipse center. Second click sets the first radius and orientation of the ellipse. Third click sets the other radius and the start of the arc. The fourth click sets the end of the arc. |
|||
* После четвертого нажатия создается дуга по эллипсу вместе с набором вспомогательной геометрии, привязанной к нему (большой диаметр, малый диаметр, два фокуса). Вспомогательная геометрия может быть удалена вручную, если не нужна, и воссоздана позже. Смотрите [[Sketcher ConstrainInternalAlignment/ru|Выравнивание Внутренних Ограничений]] и [[Sketcher RestoreInternalAlignmentGeometry/ru|Sketcher Показать Скрытую Внутреннюю Геометрию]]. |
|||
* After the fourth click, the arc of ellipse is created, together with a set of construction geometry aligned to it (major diameter, minor diameter, two foci). The construction geometry can be manually deleted if not needed, and recreated later. See [[Sketcher ConstrainInternalAlignment|Internal Alignment Constraint]] and [[Sketcher RestoreInternalAlignmentGeometry|Sketcher Show Hide Internal Geometry]]. |
|||
* Нажатие {{KEY|ESC}} или правой кнопки мыши отменяет функцию. |
|||
* Pressing {{KEY|ESC}} or clicking the right mouse button cancels the function. |
|||
==Peculiarities== |
==Peculiarities== |
Revision as of 08:18, 17 July 2019
Sketcher Дуга по эллипсу |
Системное название |
---|
Sketcher CreateArcOfEllipse |
Расположение в меню |
Эскиз → Геометрия эскиза → Дуга по эллипсу |
Верстаки |
Sketcher, Part Design |
Быстрые клавиши |
Нет |
Представлено в версии |
0.15 |
См. также |
Sketcher Эллипс по центральной точке, Sketcher Дуга |
Описание
Этот инструмент рисует дугу по эллипсу, по четырем указанным точкам: центральной, большому радиусу, начальной и конечной точкам. При запуске инструмента указатель мыши меняется на белый крест с красным значком дуги по эллипсу. Кроме того, координаты отображаются в режиме реального времени.
Последовательность нажатий указана желтыми стрелками с цифрами. C это центр, a - большой диаметр, b - малый диаметр, F1, F2 фокусы.
Как использовать
- Нажмите кнопку Дуга по эллипсу.
- Первым нажатием в 3D виде задайте точку центра эллипса. Вторым нажатием задайте первый радиус и ориентацию эллипса. Третьим нажатием задайте другой радиус и начало дуги. Четвертым нажатием задайте конец дуги.
- После четвертого нажатия создается дуга по эллипсу вместе с набором вспомогательной геометрии, привязанной к нему (большой диаметр, малый диаметр, два фокуса). Вспомогательная геометрия может быть удалена вручную, если не нужна, и воссоздана позже. Смотрите Выравнивание Внутренних Ограничений и Sketcher Показать Скрытую Внутреннюю Геометрию.
- Нажатие ESC или правой кнопки мыши отменяет функцию.
Peculiarities
- Major and minor axes of underlying ellipse are strict and cannot be swapped by resizing. The underlying ellipse must be rotated to swap the axes.
- Unlike ellipse that can be constrained to become a circle, ellipse arc cannot represent an arc of circle.
- Moving the arc of ellipse by edge is the same as moving ellipse's center.
Sketcher
- General: Create sketch, Edit sketch, Map sketch to face, Reorient sketch, Validate sketch, Merge sketches, Mirror sketch, Leave sketch, View sketch, View section, Toggle grid, Toggle snap, Configure rendering order, Stop operation
- Sketcher geometries: Point, Line, Arc, Arc by 3 points, Circle, Circle by 3 points, Ellipse, Ellipse by 3 points, Arc of ellipse, Arc of hyperbola, Arc of parabola, B-spline by control points, Periodic B-spline by control points, B-spline by knots, Periodic B-spline by knots, Polyline, Rectangle, Centered rectangle, Rounded rectangle, Triangle, Square, Pentagon, Hexagon, Heptagon, Octagon, Regular polygon, Slot, Fillet, Corner-preserving fillet, Trim, Extend, Split, External geometry, Carbon copy, Toggle construction geometry
- Sketcher constraints:
- Geometric constraints: Coincident, Point on object, Vertical, Horizontal, Parallel, Perpendicular, Tangent, Equal, Symmetric, Block
- Dimensional constraints: Lock, Horizontal distance, Vertical distance, Distance, Radius or weight, Diameter, Auto radius/diameter, Angle, Refraction (Snell's law)
- Constraint tools: Toggle driving/reference constraint, Activate/deactivate constraint
- Sketcher tools: Select unconstrained DoF, Select associated constraints, Select associated geometry, Select redundant constraints, Select conflicting constraints, Show/hide internal geometry, Select origin, Select horizontal axis, Select vertical axis, Symmetry, Clone, Copy, Move, Rectangular array, Remove axes alignment, Delete all geometry, Delete all constraints
- Sketcher B-spline tools: Show/hide B-spline degree, Show/hide B-spline control polygon, Show/hide B-spline curvature comb, Show/hide B-spline knot multiplicity, Show/hide B-spline control point weight, Convert geometry to B-spline, Increase B-spline degree, Decrease B-spline degree, Increase knot multiplicity, Decrease knot multiplicity, Insert knot, Join curves
- Sketcher virtual space: Switch virtual space
- Additional: Sketcher Dialog, Preferences, Sketcher scripting
User documentation
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub