Arch U-Образная арматура
Arch Rebar UShape |
Menu location |
---|
Arch → Rebar tools |
Workbenches |
Arch |
Default shortcut |
None |
See also |
Bent UShape Rebar |
This command is part of the Reinforcement AddOn, that you can install via menu Tools → Addons Manager |
Описание
Инструмент UShape Rebar позволяет пользователю создавать в структурном элементе арматурный стержень с изогнутой формой.
This command is part of the Reinforcement Addon, that you can install with the Addon Manager, via the menu Tools → Addon manager → Reinforcement.
Использование
- Select any face of a previously created Arch Structure object.
- Then select UShape Rebar from the rebar tools.
- A task panel will pop-out on the left side of the screen as shown below.
- Select the desired orientation.
- Give the inputs like front cover, right side cover, left side cover, bottom cover, top cover, rounding factor and diameter of the rebar.
- Select the mode of distribution either amount or spacing.
- If spacing is selected, a user can also opt for custom spacing.
- Pick selected face is used to verify or change the face for rebar distribution.
- Click OK or Apply to generate the rebars.
- Click Cancel to exit the task panel.
Taskview panel for the Arch Rebar UShape tool
Свойства
- ДанныеOrientation: It decides the orientation of the rebar (like a bottom, top, right and left).
- ДанныеFront Cover: The distance between rebar and selected face.
- ДанныеRight Cover: The distance between the right end of the rebar to right face of the structure.
- ДанныеLeft Cover: The distance between the left end of the rebar to the left face of the structure.
- ДанныеBottom Cover: The distance between rebar from the bottom face of the structure.
- ДанныеTop Cover: The distance between rebar from the top face of the structure.
- ДанныеRounding: A rounding value to be applied to the corners of the bars, expressed in times the diameter.
- ДанныеAmount: The amount of rebars.
- ДанныеSpacing: The distance between the axes of each bar.
Скриптование
Инструмент UShape Rebar можно использовать в macros и на консоли python с помощью следующей функции:
Rebar = makeUShapeRebar(f_cover, b_cover, r_cover, l_cover,
diameter, t_cover, rounding, amount_spacing_check, amount_spacing_value, orientation="Bottom",
structure=None, facename=None)
- Creates a
Rebar
object from the givenstructure
, which is an Arch Structure, andfacename
, which is a face of that structure.- If no
structure
norfacename
are given, it will take the user selected face as input.
- If no
f_cover
,b_cover
,r_cover
,l_cover
, andt_cover
are inner offset distances for the rebar elements with respect to the faces of the structure. They are respectively the front, bottom, right, left, and top offsets.diameter
is the diameter of the reinforcement bars inside the structure.rounding
is the parameter that determines the bending radius of the reinforcement bars.amount_spacing_check
if it isTrue
it will create as many reinforcement bars as given byamount_spacing_value
; if it isFalse
it will create reinforcement bars separated by the numerical value ofamount_spacing_value
.amount_spacing_value
specifies the number of reinforcement bars, or the value of the separation between them, depending onamount_spacing_check
.orientation
specifies the orientation of the rebar; it can be"Bottom"
,"Top"
,"Right"
, or"Left"
.
Пример: Создание U Shaped арматуры.
import FreeCAD, Arch, UShapeRebar
Structure = Arch.makeStructure(length=1000, width=1000, height=400)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
Rebar = UShapeRebar.makeUShapeRebar(50, 20, 20, 20,
8, 50, 4, True, 6, "Bottom", Structure, "Face4")
Rebar.ViewObject.ShapeColor = (0.9, 0.0, 0.0)
Rebar2 = UShapeRebar.makeUShapeRebar(50, 50, 20, 20,
8, 50, 4, True, 6, "Bottom", Structure, "Face6")
Rebar2.ViewObject.ShapeColor = (0.0, 0.0, 0.9)
Изменение свойств арматуры UShape.
editUShapeRebar(Rebar, f_cover, b_cover, r_cover, l_cover,
diameter, t_cover, rounding, amount_spacing_check, amount_spacing_value, orientation,
structure=None, facename=None)
Rebar
is a previously createdUShapeRebar
object.- The other parameters are the same as required by the
makeUShapeRebar()
function. structure
andfacename
may be omitted so that the rebar stays in the original structure.
import UShapeRebar
UShapeRebar.editUShapeRebar(Rebar, 50, 50, 20, 20,
16, 20, 5, True, 5, "Top")
UShapeRebar.editUShapeRebar(Rebar2, 70, 50, 20, 20,
16, 70, 5, True, 5, "Top")
Arch
- Elements: Wall, Structure, Curtain Wall, Window, Roof, Space, Stairs, Equipment, Frame, Fence, Truss, Profile, Pipe, Pipe Connector
- Reinforcements: Straight Rebar, U-Shape Rebar, L-Shape Rebar, Stirrup, Bent-Shape Rebar, Helical Rebar, Column Reinforcement, Beam Reinforcement, Slab Reinforcement, Footing Reinforcement, Custom Rebar
- Panels: Panel, Panel Cut, Panel Sheet, Nest
- Materials: Material, Multi-Material
- Organization: Building Part, Project, Site, Building, Level, External reference, Section Plane, Schedule
- Axes: Axis, Axes system, Grid
- Modification: Cut with plane, Add component, Remove component, Survey
- Utilities: Component, Clone component, Split Mesh, Mesh to Shape, Select non-manifold meshes, Remove Shape from Arch, Close Holes, Merge Walls, Check, Toggle IFC Brep flag, 3 Views from mesh, Create IFC spreadsheet, Toggle Subcomponents
- Additional: Preferences, Import Export Preferences (IFC, DAE, OBJ, JSON, 3DS, SHP), IfcOpenShell, IfcPlusPlus, Arch API
Документация пользователя
- Начинающим
- Установка: Загрузка, Windows, Linux, Mac, Дополнительных компонентов, Docker, AppImage, Ubuntu Snap
- Базовая: О FreeCAD, Интерфейс, Навигация мыши, Методы выделения, Имя объекта, Настройки, Верстаки, Структура документа, Свойства, Помоги FreeCAD, Пожертвования
- Помощь: Учебники, Видео учебники
- Верстаки: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework