Draft Polygon/sv: Difference between revisions
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
Line 51: | Line 51: | ||
* To manually enter the coordinates for the center enter the X, Y and Z component, and press {{KEY|Enter}} after each. Or you can press the {{Button|[[Image:Draft_AddPoint.svg|16px]] Enter point}} button when you have the desired values. It is advisable to move the pointer out of the [[3D_view|3D view]] before entering coordinates. |
* To manually enter the coordinates for the center enter the X, Y and Z component, and press {{KEY|Enter}} after each. Or you can press the {{Button|[[Image:Draft_AddPoint.svg|16px]] Enter point}} button when you have the desired values. It is advisable to move the pointer out of the [[3D_view|3D view]] before entering coordinates. |
||
* The {{MenuCommand|Relative}} checkbox, displayed in FreeCAD version 0.19 and earlier, has no purpose for this command. |
|||
* Press {{KEY|G}} or click the {{MenuCommand|Global}} checkbox to toggle global mode. If global mode is on, coordinates are relative to the global coordinate system, else they are relative to the [[Draft_SelectPlane|working plane]] coordinate system. {{Version|0.20}} |
* Press {{KEY|G}} or click the {{MenuCommand|Global}} checkbox to toggle global mode. If global mode is on, coordinates are relative to the global coordinate system, else they are relative to the [[Draft_SelectPlane|working plane]] coordinate system. {{Version|0.20}} |
||
* Press {{KEY|L}} or click the {{MenuCommand|Filled}} checkbox to toggle filled mode. If filled mode is on, the created polygon will have {{PropertyData|Make Face}} set to {{TRUE}} and will have a filled face. |
* Press {{KEY|L}} or click the {{MenuCommand|Filled}} checkbox to toggle filled mode. If filled mode is on, the created polygon will have {{PropertyData|Make Face}} set to {{TRUE}} and will have a filled face. |
Revision as of 12:47, 9 August 2022
Draft_Polygon |
Menyplacering |
---|
Draft -> Polygon |
Arbetsbänkar |
Skiss |
Standard genväg |
Ingen |
Introducerad i version |
- |
Se även |
Ingen |
Description
Beskrivning
Detta verktyg frågar användaren efter en centrumpunkt och en radie. Du kan sedan specificera antalet sidor, och en regelbunden polygon kommer att skapas inuti den givna radiens cirkel. Antalet sidor och om polygonen är inskriven eller omskriven cirkeln kan ändras när som helst i objektets egenskaper. Den nyss skapade polygonen kommer att ha nuvarande linkefärg och -tjocklek.
Punkterna kan markeras med musen i 3D vyn eller genom att mata in koordinater med tangentbordet.
A Draft Polygon can be switched from inscribed to circumscribed by changing its DataDraw Mode property. The corners of a Draft Polygon can be filleted (rounded) or chamfered by changing its DataFillet Radius or DataChamfer Size respectively.
Usage
See also: Draft Tray, Draft Snap and Draft Constrain.
Bruk
- Markera en punkt på ett tomt område i 3D vyn, eller på ett existerande objekt.
- Om du håller ned CTRL så kommer din punkt att snäppa till tillgängliga snäpp platser.
- Om du håller nedSKIFT så kommer din punkt att begränsas i relation till den sista punkten.
- Skriv in siffror för att mata in en koordinat manuellt
- Om du trycker ned ESC så kommer operationen att avbrytas.
- Polygonen kan visas som en yta eller som en trådmodell, genom att ändra dess visningsläge.
Options
The single character keyboard shortcuts available in the task panel can be changed. See Draft Preferences. The shortcuts mentioned here are the default shortcuts.
- To manually enter the coordinates for the center enter the X, Y and Z component, and press Enter after each. Or you can press the Enter point button when you have the desired values. It is advisable to move the pointer out of the 3D view before entering coordinates.
- Press G or click the Global checkbox to toggle global mode. If global mode is on, coordinates are relative to the global coordinate system, else they are relative to the working plane coordinate system. introduced in version 0.20
- Press L or click the Filled checkbox to toggle filled mode. If filled mode is on, the created polygon will have DataMake Face set to
true
and will have a filled face. - Press T or click the Continue checkbox to toggle continue mode. If continue mode is on, the command will restart after finishing, allowing you to continue creating polygons.
- Press S to switch Draft snapping on or off.
- Press Esc or the Close button to abort the command.
Notes
- A Draft Polygon can be edited with the Draft Edit command.
Preferences
See also: Preferences Editor and Draft Preferences.
- To change the number of decimals used for the input of coordinates and radii: Edit → Preferences... → General → Units → Units settings → Number of decimals.
- To change the initial value of filled mode: Edit → Preferences... → Draft → General settings → Draft tools options → Fill objects with faces whenever possible. Changing the filled mode in a task panel will override this preference for the current FreeCAD session.
- If the Edit → Preferences... → Draft → General settings → Draft tools options → Use Part Primitives when available option is checked, the command will create a Part RegularPolygon instead of a Draft Polygon.
Properties
See also: Property editor.
A Draft Polygon object is derived from a Part Part2DObject and inherits all its properties. It also has the following additional properties:
Data
Draft
- DataArea (
Area
): (read-only) specifies the area of the face of the polygon. The value will be0.0
if DataMake Face iffalse
. - DataChamfer Size (
Length
): specifies the length of the chamfers at the corners of the polygon. - DataDraw Mode (
Enumeration
): specifies if the polygon isinscribed
in a circle orcircumscribed
around a circle. - DataFaces Number (
Integer
): specifies the number of sides of the polygon. - DataFillet Radius (
Length
): specifies the radius of the fillets at the corners of the polygon. - DataMake Face (
Bool
): specifies if the polygon makes a face or not. If it istrue
a face is created, otherwise only the perimeter is considered part of the object. - DataRadius (
Length
): specifies the radius of the circle that defines the polygon.
View
Draft
- VyPattern (
Enumeration
): specifies the Draft Pattern with which to fill the face of the polygon. This property only works if DataMake Face istrue
and if VyDisplay Mode isFlat Lines
. - VyPattern Size (
Float
): specifies the size of the Draft Pattern.
Scripting
See also: Autogenerated API documentation and FreeCAD Scripting Basics.
To create a Draft Polygon use the make_polygon
method (introduced in version 0.19) of the Draft module. This method replaces the deprecated makePolygon
method.
polygon = make_polygon(nfaces, radius=1, inscribed=True, placement=None, face=None, support=None)
- Creates a
polygon
object with the given number of faces (nfaces
), and based on a circle ofradius
in millimeters. - If
inscribed
isTrue
, the polygon is inscribed in the circle, otherwise it will be circumscribed. - If
placement
isNone
the polygon is created at the origin and one of its vertices will lie on the X axis. - If
face
isTrue
, the polygon will make a face, that is, it will appear filled.
Example:
import FreeCAD as App
import Draft
doc = App.newDocument()
polygon1 = Draft.make_polygon(4, radius=500)
polygon2 = Draft.make_polygon(5, radius=750)
zaxis = App.Vector(0, 0, 1)
p3 = App.Vector(1000, 1000, 0)
place3 = App.Placement(p3, App.Rotation(zaxis, 90))
Polygon3 = Draft.make_polygon(6, radius=1450, placement=place3)
doc.recompute()
- Drafting: Line, Polyline, Fillet, Arc, Arc by 3 points, Circle, Ellipse, Rectangle, Polygon, B-spline, Cubic Bézier curve, Bézier curve, Point, Facebinder, ShapeString, Hatch
- Annotation: Text, Dimension, Label, Annotation styles, Annotation scale
- Modification: Move, Rotate, Scale, Mirror, Offset, Trimex, Stretch, Clone, Array, Polar array, Circular array, Path array, Path link array, Point array, Point link array, Edit, Subelement highlight, Join, Split, Upgrade, Downgrade, Wire to B-spline, Draft to sketch, Set slope, Flip dimension, Shape 2D view
- Draft Tray: Select plane, Set style, Toggle construction mode, AutoGroup
- Snapping: Snap lock, Snap endpoint, Snap midpoint, Snap center, Snap angle, Snap intersection, Snap perpendicular, Snap extension, Snap parallel, Snap special, Snap near, Snap ortho, Snap grid, Snap working plane, Snap dimensions, Toggle grid
- Miscellaneous: Apply current style, Layer, Manage layers, Add a new named group, Move to group, Select group, Add to construction group, Toggle normal/wireframe display, Create working plane proxy, Heal, Show snap toolbar
- Additional: Constraining, Pattern, Preferences, Import Export Preferences, DXF/DWG, SVG, OCA, DAT
- Context menu:
- Layer container: Merge layer duplicates, Add new layer
- Layer: Activate this layer, Select layer contents
- Text: Open hyperlinks
- Wire: Flatten
- Working plane proxy: Write camera position, Write objects state
- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework
- Hubs: User hub, Power users hub, Developer hub