PartDesign Draft/ru: Difference between revisions
(Created page with "{{Docnav/ru |Фаска |Полость |Верстак "PartDesign" |IconL=PartDesign_Chamfe...") |
(Created page with "{{Docnav/ru |Фаска |Полость |Верстак "PartDesign" |IconL=PartDesign_Chamfe...") |
||
Line 53: | Line 53: | ||
{{Docnav |
{{Docnav/ru |
||
|[[PartDesign_Chamfer| |
|[[PartDesign_Chamfer/ru|Фаска]] |
||
|[[PartDesign_Thickness| |
|[[PartDesign_Thickness/ru|Полость]] |
||
|[[PartDesign_Workbench|PartDesign]] |
|[[PartDesign_Workbench/ru|Верстак "PartDesign"]] |
||
|IconL=PartDesign_Chamfer.svg |
|IconL=PartDesign_Chamfer.svg |
||
|IconR=PartDesign_Thickness.svg |
|IconR=PartDesign_Thickness.svg |
Revision as of 20:28, 14 September 2021
PartDesign Draft |
Системное название |
---|
PartDesign Draft |
Расположение в меню |
Part Design → Притяжка |
Верстаки |
Part Design |
Быстрые клавиши |
Нет |
Представлено в версии |
- |
См. также |
... |
Description
This tool creates angular draft on the selected faces of an object. A new separate Draft entry (followed by a sequential number if there are already existing drafts in the document) is created in the Project tree.
Usage
Parameters and OptionsAdd Face / Remove FaceClick Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. Draft AngleSet the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. Neutral PlaneClick Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. Pull DirectionClick Pull Direction, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable. Reverse Pull DirectionChecking Reverse Pull Direction will toggle the draft between positive and negative angles. Special CasesThe Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer. |
- Инструменты структуры: Part, Group
- Вспомогательные инструменты: Create body, Create sketch, Edit sketch, Map sketch to face
- Инструменты моделирования
- Инструменты данных: Create a datum point, Create a datum line, Create a datum plane, Create a local coordinate system, Create a shape binder, Create a clone
- Аддитивные инструменты: Pad, Revolution, Additive loft, Additive pipe, Additive box, Additive cone, Additive cylinder, Additive ellipsoid, Additive prism, Additive sphere, Additive torus, Additive wedge
- Субстрактивные инструменты: Pocket, Hole, Groove, Subtractive loft, Subtractive pipe, Subtractive box, Subtractive cone, Subtractive cylinder, Subtractive ellipsoid, Subtractive prism, Subtractive sphere, Subtractive torus, Subtractive wedge
- Инструменты трансформации: Mirrored, Linear Pattern, Polar Pattern, Create MultiTransform
- Отделочные инструменты: Fillet, Chamfer, Draft, Thickness
- Бинарные: Boolean operation
- Дополнительно: Migrate, Shaft design wizard, Involute gear
- Инструменты контекстного меню: Set tip, Move object to other body, Move object after other object
- Начинающим
- Установка: Загрузка, Windows, Linux, Mac, Дополнительных компонентов, Docker, AppImage, Ubuntu Snap
- Базовая: О FreeCAD, Интерфейс, Навигация мыши, Методы выделения, Имя объекта, Настройки, Верстаки, Структура документа, Свойства, Помоги FreeCAD, Пожертвования
- Помощь: Учебники, Видео учебники
- Верстаки: Std Base, Arch, Assembly, CAM, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Surface, TechDraw, Test Framework