Draft Snap Angle/tr: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 1: Line 1:
<languages/>
<languages/>

{{Docnav
{{Docnav
|[[Draft_Snap_Center|Snap Center]]
|[[Draft_Snap_Perpendicular|Perpendicular]]
|[[Draft_Snap_Intersection|Snap Intersection]]
|[[Draft_Snap_Center|Center]]
|[[Draft_Snap|Draft Snap]]
|[[Draft_Module|Draft]]
|IconL=Draft_Snap_Perpendicular.svg
|IconL=Draft_Snap_Center.svg
|IconR=Draft_Snap_Center.svg
|IconR=Draft_Snap_Intersection.svg
|IconC=Workbench_Draft.svg
|IconC=Workbench_Draft.svg
}}
}}
Line 25: Line 26:
</div>
</div>


This snap option currently only works properly for circular edges on a plane parallel to the XY plane of the global coordinate system, the angles are relative to that plane.
[[Image:Draft_Snap_Angle_example.png|400px]]

{{Caption|Snapping the second point of a line to the circle, at the 45° angle on the edge. The image superimposes all possible snapping locations, indicated by small hollow circles.}}
[[Image:Draft_Snap_Angle_example.png]]
{{Caption|Snapping the second point of a line to the -30° point on a circular edge. The small magenta circles indicate all available special cardinal points.}}


== Usage ==
== Usage ==

For general information about snapping see [[Draft_Snap|Draft Snap]].


<div class="mw-translate-fuzzy">
<div class="mw-translate-fuzzy">
Line 38: Line 43:
# Elemanı, hedef elemanın seçilen uç noktasına eklemek için tıklayın
# Elemanı, hedef elemanın seçilen uç noktasına eklemek için tıklayın
</div>
</div>

== Preferences ==

See [[Draft_Snap#Preferences|Draft Snap]].




{{Docnav
{{Docnav
|[[Draft_Snap_Center|Snap Center]]
|[[Draft_Snap_Perpendicular|Perpendicular]]
|[[Draft_Snap_Intersection|Snap Intersection]]
|[[Draft_Snap_Center|Center]]
|[[Draft_Snap|Draft Snap]]
|[[Draft_Module|Draft]]
|IconL=Draft_Snap_Perpendicular.svg
|IconL=Draft_Snap_Center.svg
|IconR=Draft_Snap_Center.svg
|IconR=Draft_Snap_Intersection.svg
|IconC=Workbench_Draft.svg
|IconC=Workbench_Draft.svg
}}
}}
Line 51: Line 60:
{{Draft Tools navi{{#translation:}}}}
{{Draft Tools navi{{#translation:}}}}
{{Userdocnavi{{#translation:}}}}
{{Userdocnavi{{#translation:}}}}
{{clear}}

Revision as of 12:38, 3 August 2021

Açı

Menü konumu
Taslak → Snap → Açı
Tezgahlar
Taslak, Yapı
Varsayılan kısayol
Hiçbiri
Versiyonda tanıtıldı
-
Ayrıca bkz
Hiçbiri

Description

Açıklama

Daire ve yayların önemli noktalarına, 45 ° ve 90 ° 'de tutturulur.

This snap option currently only works properly for circular edges on a plane parallel to the XY plane of the global coordinate system, the angles are relative to that plane.

Snapping the second point of a line to the -30° point on a circular edge. The small magenta circles indicate all available special cardinal points.

Usage

For general information about snapping see Draft Snap.

Kullan

  1. Snap modunun açıldığından emin olun
  2. FreeCAD belgesine eklenecek öğeyi seçin
  3. Öğeyi eklemek istediğiniz önemli noktalardan birinin yakınında imleci gezdirin.
  4. İmlecin sağ tarafında aşağıda yakalama modunun simgesi görünecektir.
  5. Elemanı, hedef elemanın seçilen uç noktasına eklemek için tıklayın

Preferences

See Draft Snap.