Arch tutorial/ru: Difference between revisions

From FreeCAD Documentation
(Created page with "=== Создание пользовательских окон ===")
(Created page with "Как я объяснял выше, объекты "окно" создаются из двумерного макета, составленного из з...")
Line 265: Line 265:
=== Создание пользовательских окон ===
=== Создание пользовательских окон ===


Как я объяснял выше, объекты "[[Arch Window/ru|окно]]" создаются из двумерного макета, составленного из замкнутых элементов (полилиний, кругов, прямоугольников, чего угодно). Поскольку [[Draft Module|объекты Draft]] не могут поддерживать более одного такого элемента, оконный переплёт лучше рисовать инструментами [[Sketcher Module/ru|эскизирования]]. К сожалению, при эскизировании нельзя привязываться к внешним объектам, как при черчении, что было бы полезно, поскольку у нас всё уже нарисовано. По счастью, существует инструмент для конвертирования объектов Draft в эскизы: [[Draft Draft2Sketch/ru|Draft To Sketch]].
As I explained above, [[Arch Window]] objects are created from 2D layouts, made of closed elements (wires (polylines), circles, rectangles, anything). Since [[Draft Module|Draft]] objects cannot hold more than one of these elements, the preferred tool to draw window layouts is the [[Sketcher Module|Sketcher]]. Unfortunately, with the sketcher, it is not possible to snap to external objects like with the Draft workbench, which would be useful here, since our elevations are drawn already. Fortunately, a tool exists to convert Draft objects to a sketch: The [[Draft Draft2Sketch|Draft To Sketch]] tool.


So, let's start by building our first window layout. I drew it on the elevation, using several [[Draft Rectangle|rectangles]]: One for the outer line, and 4 for the inner lines. I stopped before the door, because, remember, our door already has a frame there:
So, let's start by building our first window layout. I drew it on the elevation, using several [[Draft Rectangle|rectangles]]: One for the outer line, and 4 for the inner lines. I stopped before the door, because, remember, our door already has a frame there:

Revision as of 10:34, 28 September 2016

Руководство
Тема
Modeling
Уровень
Intermediate
Время для завершения
Авторы
Yorik
FreeCAD версия
0.14
Примеры файлов
Смотрите также
None

Введение

Этот учебник нацелен дать Вам основы работы с верстаком Arch. Он достаточно прост чтобы Вам не требовался опыт работы с FreeCAD, но некоторые навыки в приложениях 3D или BIM были бы полезны. В любом случае, Вам следует быть готовым самостоятельно искать дальнейшую информацию о работе FreeCAD в его вики-документации. Если у Вас не было предыдущего опыта с FreeCAD, как минимум Вы должны прочитать Начиная работу. Так же гляньте наш раздел учебников, и достаточно много учебников можно найти на youtube.

Назначение верстака Arch - предложить полный рабочий процесс BIM внутри FreeCAD. Поскольку он еще в разработке, не надейтесь найти в нём те же инструменты и уровень завершённости, как и в коммерческих альтернативах вроде Revit или ArchiCAD, но, с другой стороны, у FreeCADа куда более широкий спектр применений, чем у этих приложений, поэтому верстак Arch сильно выигрывает от других обслуживаемых FreeCADом дисциплин, и предлагает некоторые возможности, редко встречающиеся в традиционных приложениях BIM.

Вот, например, некоторые интересные возможности верстака Arch FreeCAD, которые Вы вряд ли найдёте в других приложениях BIM:

  • Архитектурные объекты всегда представляют собой твёрдые тела. Из надёжного механического тыла FreeCAD мы знаем важность работы с твёрдыми объектами. Это гарантирует гораздо менее подверженную ошибкам работу, и надёжные булевы операции. Поскольку разрезание трёхмерных объектов двумерными плоскостями для извлечения секций - это так же булева операция, Вы можете сразу видеть важность этого пункта.
  • Архитектурные объекты могут иметь любую форму, без ограничений. Стены не обязательно вертикальны, плиты не обязаны выглядеть как плиты. Любой твердотельный объект может быть любым архитектурным объектом. Очень сложные вещи, обычно трудно определимые в других приложениях BIM, вроде плит пола, изогнутых вверх и становящихся стеной (да, Заха Хадид, это мы о тебе), сейчас в FreeCAD вообще не проблема.
  • Вся мощь FreeCAD в ваших руках. Вы можете проектировать архитектурные объекты с помощью других инструментов FreeCAD, вроде верстака PartDesign , и после готовности преобразовать их в архитектурные объекты. В них останется вся их история моделирования, и они останутся редактируемыми. Верстак Arch так же наследует большую часть функциональности верстака Draft, таких как привязка и рабочие плоскости.
  • Верстак Arch хорошо совместим с сетками. Вы можете легко проектировать архитектурные модели в основанных на сетках приложениях вроде Blender или SketchUp и импортировать их в FreeCAD. Если Вы внимательны к качеству ваших моделей и их объекты являются твердыми телами, превращение их в архитектурные объекты потребует лишь нажатие кнопки.

На момент написания верстак Arch, как и весь FreeCAD, страдает от ограничений. Над многими из них продолжается работа, и они исчезнут в будущем.

  • FreeCAD is no 2D application. It is made for 3D. There is a reasonable set of tools for drawing and editing 2D objects with the Draft Workbench and Sketcher Workbench, but it is not made for handling very large (and sometimes badly drawn) 2D CAD files. You can usually successfully import 2D files, but don't expect very high performance if you want to keep working on them in 2D. You have been warned.
  • No materials support. FreeCAD will have a complete Material system, able to define very complex materials, with all the goodies you can expect (custom properties, material families, rendering and visual aspect properties, etc), and the Arch Workbench will of course use it when it is ready.
  • Very preliminary IFC support. You can already import IFC files, quite reliably, provided IfcOpenShell is installed on your system, but exporting is still not officially supported. This is worked on both by the FreeCAD and IfcOpenShell developers, and in the future we can expect full-powered IFC support.
  • Most Arch tools are still in development. That means that automatic "wizard" tools that create complex geometry automatically, such as Arch Roof or Arch Stairs can only produce certain types of objects, and other tools that have presets, such as Arch Structure or Arch Window only have a couple of basic presets. This will of course grow over time.
  • Relations between objects in FreeCAD are still not officially available. These, for example the relation between a window and its host wall, are currently implemented in the Arch Workbench with temporary (and therefore somewhat limited) methods. Many new possibilities will arise when this feature will be fully available.
  • Units are being implemented in FreeCAD, which will allow you to work with any unit you wish (even imperial units, you guys from the USA can be eternally grateful for this to Jürgen, FreeCAD's godfather and dictator). But at the moment the implementation is not complete, and the Arch workbench still doesn't support them. You must consider it "unit-less".


Требуется FreeCAD версии 0.14

Этот учебник написан с использованием FreeCAD версии 0.14. Чтобы следовать ему, Вам нужен как минимум этот номер версии. Ранние версии могут содержать не все нужные инструменты или содержать не все представленные опции.


Типичный рабочий процесс

Верстак Arch в основном сделан под два типа рабочих процессов:

  • Создать свою модель быстрым, базирующемся на сетках приложением вроде Blender или SketchUp, и импортировать её в FreeCAD, чтобы получить виды в плане и в сечении. FreeCAD сделан для точного моделирования, на гораздо более высоком уровне, чем обычно требуется в архитектурном моделировании, создание моделей прямо в FreeCAD может быть тяжёлым и сложным. Поэтому такой процесс имеет большие преимущества. Он описан в этой статье моего блога. Если Вас заботит корректность и точность модели (чистые, твердотельные, не manifold сетки), этот рабочий процесс даёт ту же производительность, что и другие.
  • Создание модели прямо в FreeCAD. Это то, что будет показано в этом учебнике. Мы будем использовать в основном три верстака: разумеется, Arch, но кроме того Draft, все инструменты которого включены в Arch, так что переключение не требуется, и Sketcher. Для удобства Вы можете сделать то, что обычно делаю я, то есть создать в верстаке Arch пользовательскую панель инструментов, с помощью Панели инструментов -> Настроить, и добавить часто используемые инструменты из верстака Sketcher. Это мой "настроенный" верстак Arch:

В этом учебнике мы будем моделировать дом в трехмерном пространстве на основе плоских чертежей, загруженных из сети, и создадим по нему двумерные чертежи, вроде планов, фасадов и сечений.

Подготовка

Вместо создания проекта с нуля для экономии времени возьмём для моделирования готовый демонстрационный. Я выбрал этот чудный дом известного архитектора Виланова Артигас (смотрите несколько картинок Педро Кока), поскольку это близко к тому, где я живу, просто, это прекрасный пример привлекательной модернистской архитектуры Сан-Паулу (есть даже на продажу если вы найдёте "немножко" реалов на это), и легко доступен чертёж в формате dwg.

Мы будем использовать двумерный чертёж в формате DWG, полученный с вышеуказанной ссылки (от Вас требуется регистрация на том сайте, но это бесплатно, или Вы можете получить версию dxf напрямую здесь) в качестве базы для создания нашей модели. Так что сначала Вам надо загрузить файл, разархивировать его, и открыть файл DWG в приложении вроде DraftSight. Или Вы можете преобразовать его в файл DXF с помощью свободной утилиты вроде Teigha File Converter. Если у Вас Teigha converter установлен (и путь к нему установлен в настройках модуля Arch), FreeCAD так же может импортировать файлы DWG самостоятельно. Но, поскольку эти файлы могут быть плохого качества или слишком большими, обычно лучше сначала открыть их в двумерном приложении САПР и сделать небольшую обработку.

Здесь я убрал все детали рисунка, рамку и угловые штампы, сделал "очистку" ("purge" на языке AutoCADа) для удаления неиспользованных объектов, перенёс сечения в разумные положениях относительно вида сверху, и переместил всё в точку (0,0). После этого наш файл может быть спокойно открыть в FreeCAD. Проверьте различные опции, доступные в Правка -> Параметры -> Draft -> Импорт/Экспорт, они влияют на то, как (и как быстро) файлы DXF/DWG будут импортированы.

Вот как файл выглядит после открытия в FreeCAD. Я так же изменил толщину стен (содержимое группы "muros"), и перевернул множество дверей, импортируемых с неправильным масштабом, с помощью инструмента Draft Scale:

Импортер DXF (который так же обрабатывает файлы DWG, поскольку при импорте файлов DWG их просто конвертируют сначала в DXF), группирует объекты по слоям. В FreeCAD нет слоёв, но есть группы. Группы предлагают аналогичный путь организации объектов в Ваших файлах, но не имеют особых параметров, применяемых ко всему их содержимому, как в слоях AutoCAD. Но они могут быть помещены внутри других групп, что очень удобно. Первое, что нам следует сделать, это создать новую группу в древе проекта, кликнув правой кнопкой на иконе документа, добавив группу, переименовать её в "base 2D plans", и перетащить объекты в неё.

Построение стен

Подобно большинству архитектурных объектов, стены могут быть построены поверх большого множества других объектов: линий, полилиний, набросков, поверхностей или тел (или даже на пустом месте, в таком случае они определяются высотой, шириной и длиной). Получившаяся геометрия стен зависит от базовой геометрии, и добавленных к ней параметров, вроде ширины и высоты. Как Вы догадываетесь, стена, базирующаяся на линии. использует её в качестве направляющей, если базируется на грани, то использует грань как базовый отпечаток, а стена на базе твёрдого тела будет просто использовать форму этого тела. Это позволяет считать практически любую форму способной стать стеной.

Возможны различные стратегии построения стен в FreeCAD. При одной можно построить полный "поэтажный план" с помощью эскизирования, и построить из него единый большой стеновой объект. Эта техника работает, но Вы сможете назначить лишь одну толщину стен для всех стен проекта. Или Вы можете построить каждый участок стены из отдельных сегментов линий. Или, что мы будем здесь делать, и то, и другое: мы создадим набор полилиний поверх импортированного плана, по одной для каждого типа стен:

Как видите, я нарисовал красным линии, которые станут бетонными стенами (поиск картинок домов поможет Вам увидеть различные типы стен), зелёным станут внешние кирпичные стены, а синие станут внутренними стенами. Я провёл линии через двери, поскольку двери будут вставлены в стены позднее, and will create their openings automatically. Стены так же могут быть выравнены по левому, правому краю или центру, так что не важно, по какой стороне Вы рисовали базовую линию. Я старался избегать пересечений насколько можно, поскольку наша модель будет при этом чище. Но мы позаботимся о пересечениях позднее.

Когда всё будет готово, если хотите, поместите все эти линии в новую группу, выберите каждую линию по одной, и нажмите инструмент Стена для создания стен из каждой из них. Можно так же выбрать несколько стен за раз. После выполнения этого и корректировки толщины (внешние стены толщиной 25 см, внутренние стены толщиной 15 см) и некоторого выравнивания, наши стены готовы:

Мы так же можем создать наши стены с нуля. Если Вы нажмёте кнопку Стена без выбранного объекта, Вы сможете указать двее точки на экране для построения стены. Но внутри инструмент Стена на самом деле нарисует линию, на которой и построит стену. Поэтому я счёл более дидактичным показать, как всё работает на деле.

Заметили, что я внимательно следил, чтобы не было пересечения стен? Это убережёт нас от головной боли далее, например, если мы экспортируем нашу работу в другое приложение, для которого это будет проблемой. Я сделал только одно пересечение, где мне было лень рисовать два маленьких сегмента линий, и нарисовал одну большую полилинию пересекающей другую. Это надо исправить. По счастью, все архитектурные объекты имеют отличную возможность добавляться один к другому. Это объединяет их геометрии, но они по-прежнему смогут редактироваться независимо. Чтобы добавить одну из пересекающихся стен к другой, выделите первую, CTRL + выбрать вторую, и нажмите инструмент Добавить компонент:

Слева две пересекающиеся стены, справа результат добавления одной к другой.

Важное замечание о параметрических объектах

Кое-что важно принять во внимание прямо сейчас. Как вы видели, во FreeCAD всё параметрическое: наши новые "объединённые" стены сделаны из двух стен, каждая основана на базовой линии. Если Вы раскроете их в древе проекта, Вы увидите всю цепочку зависимостей. Как Вы можете представить, эта маленькая игра может быстро стать очень сложной. Более того, если Вы уже знаете как работать с эскизированием, Вы можете захотеть рисовать базовые линии с геометрическими ограничениями. Эта сложность имеет свою цену: она поднимает объём вычислений, которые FreeCAD должен выполнять, чтобы держать геометрическую модель в соответствии с данными, по экспоненте. Так что думайте об этом, не добавляйте лишнюю сложность там, где не надо. Держите баланс между простыми и сложными объектами, и придерживайте их для случаев, когда они реально необходимы.


Например, можно было нарисовать все базовые линии, не обращая внимания на пересечения, и исправить всё с помощью Arch Add позднее. Но это сильно увеличило бы сложность модели, и без всякой пользы. Лучше сделать это правильно с самого начала, и сохранять их геометрически простыми.

Теперь, когда наши стены в порядке, нам нужно увеличить их высоту до пересечения с крышей. Затем, поскольку стены всё ещё не могут быть автоматически обрезаны крышей (это когда-нибудь будет), мы сделаем пустой объект с формой крыши, чтобы вычесть его из наших стен.

Сначала, посмотрев на чертежи, мы видим, что наивысшая точка крыши на уровне 5,6 метров от земли. Так что сделаем все наши стены высотой 6 метров, так что мы будем уверены, что они будут обрезаны нашим фиктивным объёмом крыши. Почему 6, а не 5,6 метров? Если Вы работали с булевыми операциями (добавление, вычитание, пересечение), то отмечали, что они не любят работать с соприкасающимися поверхностями. Они предпочитают четко пересекающиеся объекты. Так что делая это, мы предохраняем себя.

Чтобы увеличить высоты наших стен, просто выделите их (не забудьте те, что мы добавили одна к другой) в древе проекта, и измените параметр "height".

Перед тем как сделать нашу стену и обрезать стены, сделаем остальные объекты, которые должны быть обрезаны: стены верхней студии, и колонны. Стены студии делаются так же, как остальные, на главном виде сверху, но они будут подняты на уровень 2,6 метра. Так что, чтобы их верх был на уровне 6 метров, мы дадим им требуемую высоту 3,4 метра. Когда это будет готово, мы поднимем наши стены на 2,6 метра: Выделите их все, переключитесь на фронтальный вид (Вид -> Стандартные виды -> Спереди), нажмите кнопку Draft Move, выберите первую точку, затем введите координаты 0, 2.6, 0, и нажмите Enter. Ваши объекты теперь подняты на 2,6 метра:

О координатах

{{{2}}}


Теперь подвинем наши стены горизонтально, к их правильному положению. Поскольку мы имеем точки для захвата, это проще: нажимаем инструмент Draft Move, и перемещаем из с одной точки в другую:

В конце я сменил цвет некоторых стен на кирпичный (чтобы легче их отмечать), и сделал небольшие изменения: некоторые стены не поднимаются до крыши, но остаются на высоте 2,6 метра. Я подправил высоту этих стен.

Построение структур

Теперь, когда нам надо обрезать стены вычитаемым объемом, нам следует так же посмотреть, нет ли других объектов, которые следует обрезать таким же образом. Они есть, это некоторые колонны. Это хорошая возможность представить следующий архитектурный объект, Структуру. Объект Структура похож на стену, но их делают не по базовым линиям. Взамен, над ними работают как с вытягиваемым профилем (вдоль линии профиля или нет). Профилем структуры может быть любой плоский объект, при одном требовании: это должна быть замкнутая фигура.

Для наших колонн мы используем иную стратегию, чем для стен. Вместо "рисования" поверх чертежа, мы напрямую используем объекты из них: окружности, которые которые показывают колонны на виде сверху. Теоретически, мы должны просто выбрать один из них, и нажать кнопку Структура. Но если мы сделаем это, мы получим "пустой" объект. Это потому, что мы не можем быть уверены, как объект нарисован в файле DWG, и нередко это не замкнутые фигуры. Поэтому, перед тем как превращать их в колонны, превратим их в грани, дважды используя к ним инструмент Draft Upgrade. Сначала превратив их в замкнутые полилинии, потом превратив полилинии в грани. Следующий шаг не обязателен, но если у Вас есть грань, у вас 100% гарантия, что она замкнута (иначе грань не будет получена).

После преобразования всех наших колонн в грани, мы можем обработать их инструментом Структура, и подстроить высоту (некоторые имеют 6 метров, другие - 2,25 метров в высоту):

На картинке выше Вы можете видеть две колонны, которые пока как в файле DWG, две уже превращённые в грани, и две превращённые в Структуру с высотой 6 метров и 2,25 метра.

Заметьте, что эти разные архитектурные объекты (стены, структуры и всё остальное) имеют между собой много общего (например, они могут быть добавлены один к другой, как мы видели это со стенами, и каждый может быть превращён в другой). Так что это дело вкуса, мы могли сделать наши колонны с помощью стен, и преобразовать их при необходимости. На деле, некоторые из наших стен бетонные, нам следует в дальнейшем преобразовать их в структуры.

Вычитание

Настало время создать объём для вычитания. Проще всего нарисовать его профиль поверх сечения. Затем повернём его и поместим в нужную позицию. Поняли, почему я в начале поместил сечения и лестницы таким образом? Это будет удобно для черчения нужного нам объёма, а потом перемещения его в нужную позицию модели.

Нарисуем объём больше крыши, который будет вычитаться из наших стен. Для этого я нарисовал две линии поверх базы крыши, затем расширил их ещё немного с помощью инструмента Draft Trimex. Затем я нарисовал полилинию, с привязкой к этим линиям, и пошёл выше 6 метров. Я так же нарисовал голубую линию на уровне земли (0,00), которая будет осью вращения.

Теперь сложная часть: мы используем инструмент Draft Rotate для вращения нашего профиля на 90 градусов вверх, в правильную позицию для выдавливания. Для этого сначала изменим рабочую плоскость на YZ. После этого вращение будет в этой плоскости. Но если мы сделаем как мы делали раньше, и установим наш вид на боковой вид, будет трудно видеть и выбрать наш профиль, и знать где базовая точка, вокруг которой надо вращать, верно? Поэтому мы должны установить рабочую плоскость вручную: нажать кнопку Draft SelectPlane (она на панели "Задачи" окна древа проекта), и установим её в YZ (это боковая сторона). Когда Вы установите так рабочую плоскость вручную, она не меняется в зависимости от Вашего вида. Вы можете теперь вращать Ваш вид как угодно чтобы получить хороший обзор того, что Вам надо выделить. Чтобы вернуть рабочую плоскость назад в автопереключение по виду, нажмите кнопку Draft SelectPlane снова и установите её в "None".

Теперь поворот сделать легко: Выберите профиль, нажмите кнопку Draft Rotate, нажмите кнопку на голубой линии, введите 0 как стартовый угол, и 90 как угол поворота:

Теперь всё, что требуется, это переместить профиль немного ближе к модели (если нужно, установите рабочую плоскость в XY), и выдавить его. Это может быть выполнено либо инструментом Part Extrude, или Draft Trimex, который так же имеет скрытую возможность выдавливать грани. Убедитесь, что выдавленное Вами больше чем все стены, из которых оно вычитается, во избежание появления стыка поверхностей:

Теперь вступает в действие обратный инструмент, обратный Arch Add: Arch Remove. Как Вы догадываетесь, он тоже создаёт объект-потомок, но его форма вычитается из объекта вместо объединения. Так что теперь всё просто: выделить объём для вычитания (я переименовал его в "Roof volume to subtract" в древе проекта, чтобы его было легче заметить), CTRL + выбрать стены, и нажать кнопку Arch Remove. После вычитания вычитаемый объём исчезнет из окна трёхмерного вида и древа проекта. Это потому что он был отмечен как производный от стены, и был "проглочен" ею. Выберите стену, раскройте её в древе проекта и Вы увидите наш вычитаемый объём.

Теперь выберите объём из древа проекта, CTRL + выберите следующую стену, нажмите Arch Remove. Повторите для следующей стены, пока не обрежете всё как надо:

Помните, что и для Arch Add и для Arch Remove важен порядок, в каком выбраны объекты. Хост всегда последний, как при "Удалении X из Y" или "Добавить X к Y"

Замечание про добавление и вычитание

Архитектурных объекты, которые поддерживают сложение и вычитание (все, кроме объектов визуальной помощи вроде осей) отслеживают эти объекты через два параметра, "Additions" и "Subtractions" соответственно, которые содержат список связей с добавленными или вычтенными объектами. Те же объекты могут быть в списке нескольких объектов, как в случае, описанном выше. Каждый из "предков" постарается "проглотить" его в древе проекта, но он останется в нём. Но Вы всегда можете редактировать этот список для каждого объекта, двойным кликом в древе проекта, при котором FreeCAD входит в режим редактирования. Выход из режима редактирования нажатием кнопки Escape.


Создание крыш

Теперь всё, что нам осталось для завершения структуры, это сделать крышу и малые внутренние перекрытия. Опять таки, проще всего нарисовать их профили поверх секции, с помощью инструмента полилиния. Здесь я нарисовал 3 профиля поверх каждого из них (я переместил их в сторону чтобы Вам было лучше видно). Зелёный будет использоваться для боковых границ потолочной плиты, синий для боковых частей, красные для центральной части, которая находится над блоком ванной:

Далее, мы должны повторить вышеуказанную операцию вращения, чтобы повернуть объекты в вертикальную позицию, переместить их в нужные места, и копировать те из них, которые должны быть выдавлены дважды, инструментом Перемещение, с нажатой клавишей ALT, которая создаёт копии вместо перемещения реального объекта. Я так же добавил ещё два профиля для боковых стен прохода к ванной.

Когда всё на своём месте, это как раз для использования инструмента Draft Trimex для выдавливания, затем конвертировать их в структуры.

После этого мы замечаем несколько проблем: две колонны справа слишком коротки (они должны идти под крышу), и есть зазор между плитой и стенами студии в дальнем правом углу (символ уровня 2,6 метра на виде сечения, очевидно, был ошибочен). Благодаря параметричности объектов, все их легко исправить: для колонн просто измените их высоту до 6 метров, выцепите в древе проекта вычитаемый объём для крыши и вычтите его из колонн. Для стен это даже проще: опустите их чуть ниже. Поскольку вычитание продолжается в том же месте, геометрия стен адаптируется автоматически.

Теперь последняя вещь, которую надо исправить, это маленькая плита в ванной, которая пересекает некоторые стены. Исправим это созданием нового вычитаемого объёма, и вычтя его из этих стен. Другая возможность инструмента Draft Trimex, который мы использовали для выдавливания, что он так же может выдавить единственную грань существующего объекта. Это создаёт новые, отдельные объекты, так что нет риска "испортить" другие объекты. Так что мы можем выбрать базовую грань малой плиты (гляньте на неё снизу модели), затем нажмите кнопку Draft Trimex и выдавите его вверх выше крыши. Затем вычтите его из двух внутренних стен ванной с помощью инструмента Arch Remove.

Полы, лестницы и дымоход

Теперь, когда наша структура готова, нам осталось сделать несколько небольших объектов.

Дымоход

Let's start with the chimney. Now you already know how it works, right? Draw a couple of closed wires, move them up at their correct height with the Draft Move tool, extrude them with the Draft Trimex tool, turn the bigger one into a structure, and subtract the smaller ones. Notice how the chimney tube wasn't drawn on the plan view, but I found its position by dragging blue lines from the section views.

Перекрытия

Перекрытия плохо показаны на исходном чертеже. Глядя на сечения, мы не знаем, где и какой толщины стоят плиты перекрытий. Поэтому я предположил что все стены лежат на фундаментных блоках, на уровне 0,00, и что есть плиты пола, так же сидящие на этих блоках, толщиной 15 см. Поэтому плиты пола не подходят под стены, а обходят их. Мы можем сделать это, создав большую прямоугольную плиту, затем вычитая стены, но мы помним, что операция вычитания ресурсоёмкая. Лучше сделать её из маленьких элементов, это будет "дешевле" по вычислительным ресурсам, но так же, поскольку мы сделаем это интеллигентно, комната за комнатой, это будет полезно при вычислении площади пола в дальнейшем:

Когда будут нарисованы полилинии, превратим их в структуры, и дадим им высоту 0,15:

Лестницы

Now the stairs. Met the next of the Arch tools, the Arch Stairs. This tool is still in a very early stage of development, at the time I'm writing, so don't expect too much of it. But it is already pretty useful to make simple, straight stairs. One concept is important to know, the stairs tool is thought to build stairs from a flat floor up to a wall. In other words, when viewed from the top, the stairs object occupies exactly the space that it occupies on the plan view, so the last riser is not drawn (but it is of course taken into account when calculating heights).

In this case, I preferred to build the stairs on the section view, because we'll need many measurements that are easier to get from that view. Here, I drew a couple of red guidelines, then two blue lines that will be the base of our two pieces of stairs, and two green closed wires, that will form the missing parts. Now select the first blue line, press the Arch Stairs tool, set the number of steps to 5, the height to 0.875,the width to 1.30, the structure type to "massive" and the structure thickness to 0.12. Repeat for the other piece.

Then, extrude both green wires by 1.30, and rotate and move them to the right position:

On the elevation view, draw (then rotate) the border:

Then move everything into place:

Don't forget also to cut the column that crosses the stairs, because in BIM it's always bad to have intersecting objects. We are building like in the real world, remember, where solid objects cannot intersect. Here, I didn't want to subtract the column directly from the stairs (otherwise the column object would be swallowed by the stairs object in the tree view, and I didn't like that), so I took the face on which the column was built, and extruded it again. This new extrusion was then subtracted from the stairs.

Right! All the hard work is now done, let's go on with the very hard work!

Окна и двери

Окно модуля Arch достаточно сложный объект. Они используются для всех видов "вставляемых" объектов, вроде окон или дверей. Да, во FreeCAD двери - это особый вид окон. В реальной жизни тоже, если подумать, не так? Инструмент окно пока непрост в использовании, но считайте это компромиссом, поскольку он был построен для максимизации возможностей. С его помощью можно сделать практически любой вид окна, какой Вы можете представить. Но когда инструмент получит больше предустановок, ситуация должна улучшиться в будущем .

Объект окно устроено примерно так: он базируется на двумерном макете, любом плоском объекте, но предпочтительно на эскизе, содержащем замкнутые полилинии. Эти полилинии определяют различные части окна: внешние и внутренние рамки, стеклянные и непрозрачные панели и т.д.. Окно имеет свойства, которое показывает, что делать с каждой из этих полилиний: выдавить его, поместить его с соответствующим смещением и т.д.. В итоге, окно может быть вставлено в основной объект вроде стены или структуры, и вокруг неё автоматически создаётся отверстие под него. Это отверстие вычисляется выдавливанием самой большой полилинии, найденной в макете окна.

Есть два способа создания таких объектов в FreeCAD: используя предустановки, или рисуя раскладку окна с нуля. Мы рассмотрим два метода. Но помните, что метод предустановок только создаёт раскладку и определяет необходимые выдавливания для Вас.

Использование предустановок

When pressing the Arch Window tool with no object selected, you are invited either to pick a 2D layout, or to use one of the presets. Let's use the "Simple Door" preset to place the main entrance door of our model. Give it a width of 1m, a height of 2.45m, a W1 size of 0.15m, and leave the other parameters to 0.05m. Then click the lower left corner of the wall, and your new door is created:

You will notice that your new door won't appear in the tree view. That is because, by snapping to a wall, we indicated that wall as its host object. Consequently, it has been "swallowed" by the wall. But a right click on it -> Go to selection will find it in the tree.

In this case, as our window is not inserted in any wall (the opening was there already), we might as well detach our window from its host wall. This is done by double-clicking the host wall in the tree view to enter its edit mode. There, you will see the window in its "Subtractions" group. Simply select the window there, press the "remove element" button, then "OK". Our window has now been removed from its host wall, and lies at the bottom of the tree view.

We have a second door, exactly the same as this one, a bit on the left. Instead of creating a new door from scratch, we have two ways to make a copy of the previous one: By using the Draft Move tool, with the ALT key pressed, which, as you already know, copies an object instead of moving it. Or, even better, we can use the Draft Clone tool. The clone tool produces a "clone" of a selected object, that you can move around, but that retains the shape of the original object. If the original object changes, the clone changes too.

So all we need to do now is select the door, press the Draft Clone tool, then move the clone to its correct position with the Draft Move tool.

Organizing your model

Now would be a good time to do a bit of housecleaning. Since we already have two windows, it is a good moment to do some cleaning in the tree view: Create a new group, rename it to "windows", and drop the 2 windows in it. I also recommend you to separate other elements that way, such as the walls and structures. Since you can also create groups inside groups, you can organize further, for example by placing all elements that form the roof into a separate group, so it is easy to turn on and off (turning a group visible or invisible does the same with all objects inside).

The Arch Workbench has some additional tools to organize your model: the Arch Site, Arch Building and Arch Floor. Those 3 objects are based on the standard FreeCAD group, so they behave exactly like groups, but they have a couple of additional properties. For example, floors have the ability to set and manage the height of the contained walls and structure, and when they are moved, all their contents are moved too.

But here, since we have only one building with only one (and a half) floor, there is no real need to use such objects, so let's stick with simple groups.

Now, let's get back to work. Turn off the roof group, so we can see better inside, and switch the Display Mode of the floor objects to Wireframe (or use the Draft ToggleDisplayMode tool) so we can still snap to them, but we can see the plan view underneath. But you can also turn off the floors completely, then place your doors at level 0, then raise them of 15cm with the Draft Move tool.

Let's place the interior doors. Use the "Simple Door" preset again, make doors of 1.00m and 0.70m wide x 2.10m high, with W1 size of 0.1m. Make sure you snap to the correct wall when you place them, so they automatically create a hole in that wall. If it is hard to place them correctly, you can place them at an easier location, at the corner of the wall, for example, then move them. The "hole" will move together.

If by mistake you hosted a window in the wrong wall, it is easy to fix: Remove the window from the "Subtraction" group of the host wall in edit mode, as we saw above, then add it to the "Subtraction" group of the correct wall, by the same method, or, simply, using the Arch Remove tool.

A little work later, all our doors are there:

After a closer look at the elevation view, I now detected another error: The top of the brick walls is not as 2.60m, but 17.5cm lower, that is, 2.425m. Fortunately, windows based on presets have a facility: You can alter their general dimensions (width and height) from their properties. So let's change their height to 2.425 - 0.15, that is, 2.275. The second window, as it is a clone of the first one, will adapt too. This is basically where the true magic of parametric design appears.

Now we can look at the really interesting stuff: How to design your own custom windows.

Создание пользовательских окон

Как я объяснял выше, объекты "окно" создаются из двумерного макета, составленного из замкнутых элементов (полилиний, кругов, прямоугольников, чего угодно). Поскольку объекты Draft не могут поддерживать более одного такого элемента, оконный переплёт лучше рисовать инструментами эскизирования. К сожалению, при эскизировании нельзя привязываться к внешним объектам, как при черчении, что было бы полезно, поскольку у нас всё уже нарисовано. По счастью, существует инструмент для конвертирования объектов Draft в эскизы: Draft To Sketch.

So, let's start by building our first window layout. I drew it on the elevation, using several rectangles: One for the outer line, and 4 for the inner lines. I stopped before the door, because, remember, our door already has a frame there:

Then, select all the rectangles, and press the Draft To Sketch button (and delete the rectangles, because this tool doesn't delete the original objects, in case something goes wrong). Then, with the new sketch selected, press the Arch Window tool:

The tool will detect that the layout has one outer wire and several inner wires, and automatically proposes you a default configuration: One frame, made by subtracting the inner wires from the outer one, extruded by 1m. Let's change that, by entering the window's edit mode, by double-clicking on it in the tree view:

You will see a "Default" component, that has been created automatically by the Window tool, that uses the 5 wires (always subtracting the other ones from the biggest one), and has an extrusion value of 1. Let's change its extrusion value to 0.1, to match what we used in the doors.

Then, let's add 4 new glass panels, each using a single wire, and give them an extrusion of 0.01, and an offset of 0.05, so they are placed at the middle of the frame. This will be how your window looks like when you are finished:

I suppose now you must have understood the power of this system: Any combination of frames and panels of any shape is possible. If you can draw it in 2D, it can exist as a full valid 3D object.

Now, let's draw the other pieces, then we'll move everything into place together. But first. we'll need to do some corrections to the base 2D drawing, because some lines are clearly missing, where the windows meet the stairs. We can fix that by offsetting the stairs line by 2.5cm with the Draft Offset tool (with ALT pressed of course, to copy our lines instead of moving them). Now we can draw our layout, with wires, then convert them to a sketch, then making a window of it.

After doing that a couple of times (I made it in 4 separate pieces, but it's up to you to decide), we have our facade complete:

Now, as before, it's just a matter of rotating the pieces, and moving them to their correct position:

Last missing piece, there is a segment of wall that didn't appear on the plan view, that we need to add. We have several options for that, I chose to draw a line on the ground plane, then move it up to the correct height, then create a wall from it. Then, we also need to fish up our roof subtraction volume (it must have stayed in the last column), then subtract it. Now this side of the building is ready:

Ready? Not quite. Look at the image above, we did our doors with a 5cm frame, remember (it was the default from the preset). But the other windows have 2.5cm frames. This needs to be fixed.

Editing windows

We already saw how to build and update window components, via the window's edit mode, but we can also edit the underlying sketch. Preset windows are not different than custom windows, the Arch Window tool only created the underlying sketch fo you. Select our door object (the original, not the copy, remember, we made a clone), and expand it in the tree view. There is our sketch. Double-click it to enter edit mode.

the Sketcher Workbench is an extremely powerful tool. It doesn't have some of the Draft conveniences, such as snapping or working planes, but it has many other advantages. In FreeCAD you will frequently use one or another depending on the need. The most important feature of the sketcher is constraints. Constraints allow you to automatically fix the position of some elements relative to others. For example, you can force a segment to always be vertical, or to always be at a certain distance to another.

When we edit our door sketch, we can see that it is made on a fully constrained sketch:

Now all we need to do is edit the 5cm distances between the outer line and the inner line, by double-clicking them, and changing their value to 2.5cm (Remember, the units are still not fully functional at the time I'm writing this). After clicking the "OK" button, our door (and its clone) have been updated.

Working without 2D support

Until now our work has been relatively easy, because we had the underlying 2D drawings to base our work upon. But now, we must do the opposite facade and the glass atrium, and things are getting more complicated: The opposite facade drawing has a lot of wrong things, doesn't represent the atrium at all, and we have simply no drawing for the inner walls of the atrium. So we will need to invent a couple of things ourselves. Be sure to have a look at reference pictures to figure out how things are made. Or do it as you wish!

One thing we can already do: duplicate the complicated stairs window with the Draft Move tool, because it is equal on both sides:

Note that here, I preferred to duplicate with the Draft Move tool instead of using a clone, because the clone currently doesn't support different colors inside objects. The difference is that the clone is a copy of the final shape of the original object, while if you copy an object, you create a new object and give it all the same properties as the original one (therefore, also its base sketch and its window components definition, which are both stored as properties).

Now we must attack the parts that are not drawn anywhere. Let's start with the glass wall between the sitting room and the atrium. It'll be easier to draw it on the elevation view, because we'll get the correct height of the roof. Once you are in plan view, you can rotate the view from the menu View -> Standard Views -> Rotate left or right, until you get a comfortable view to work, like this:

Note how on the image above, I made a line from the model to the left section, to get the exact width of the window. Then, I reproduced that width on the elevation view and divided it into 4 pieces. Then I built one main window piece, plus 4 additional windows for the sliding doors. The sketcher sometimes has difficulties with overlapping wires, that's why I preferred to keep them separated like this:

After the necessary rotations, everything clicks perfectly into place:

We still need some corner piece there. A little useful trick with the Draft SelectPlane tool, if you have a face selected when you press the button, the working plane matches this face (at least its position, and if the face is rectangular, it also tries to match its axes). This is useful to draw 2D objects directly on the model, such as here, we can draw a rectangle to be extruded directly at its correct position:

Then let's do the two remaining pieces. One is easy, it is a copy of what's on the other side, so we can simply use the 2D drawing:

The other one is a bit tricky, by looking at the pictures, we see that it has many vertical divisions, like the stairs windows. By chance (or very good design from Vilanova Artigas), the width of our window, of 4.50m, is exactly the same as the stairs window, so we can use the exact same division: 15 pieces of 30cm. Here I used the Draft Array tool to copy over the two lines 15 times,and drew rectangles on top of them:

Once this is done, we can create our window with the same method we already know. Another small useful trick, in case you haven't found it yourself already: When editing a window, if you change the name of a component, it actually creates a duplicate of it. So to create the 15 inner glass panels, instead of clicking 15 times the "add" button and fill 15 times the data, you can just keep editing one, and change its name and wire, it will create a copy each time.

After the window is rotated and moved into place, the atrium is complete:

Edits and fixes

Now when we look at our back elevation, and compare it with the plan, we see that there are some differences that need to be fixed. Namely, the bedroom windows are smaller than I first thought, and we'll need to add some more walls. In order to do that properly, some floors need to be cut:

We have of course several ways to do that, making a subtraction volume would be an easy way, but it would add unnecessary complexity to the model. Better to edit the base wire of each floors. This is where the Draft Edit mode comes into action. By expanding these floors in the tree view, then making their base wire visible, we can then double-click them to enter edit mode. There, we can move their points, or add or remove points. With this,editing our floor plates becomes easy.

After some more sweat (the person who made those drawings obviously became pretty lazy when did this last elevation, much is drawn wrong), we finally have our complete house:

Note the chimney tube, which is made from a circle I used to make a hole in the chimney block, that I extruded, then converted into a tube with the Part Offset tool.

Problems in objects

Sometimes an object you made can have problems. For example, the object it was based onto has been deleted, and the object can therefore not recalculate its shape. These are usually shown to you by a little red sign on their icon, and/or a warning in the output window. There is no generic recipe to fix these problems, because they can have many origins. But, the easiest way to solve them is often to delete them, and, if you didn't delete their base objects, recreate them.


Output

Now, after all the hard work we passed through to build this model, comes the reward: What can we do with it? Basically, this is the big advantage of working with BIM, all our traditional architectural needs, such as 2d drawings (plans, sections, etc), renderings, and calculations (bills of quantities, etc) can all be extracted from the model. And, even better, regenerated every time the model changes. I'll show you here how to obtain these different documents.

Preparations

Before starting to export stuff, one consideration is interesting to do: As you saw, our model is becoming increasingly complex, with a lot of relationships between objects. This can make subsequent calculation operations, such as cutting through the model, heavy. One quick way to magically "simplify" drastically your model, is to remove all of this complexity, by exporting it to the STEP format. That format will preserve all your geometry, but will discard all the relationships and parametric constructions, keeping only the final shape. When reimporting that STEP file into FreeCAD, you will get a model that has no relationship, and a much smaller file size. Think of it as an "output" file, that you can regenerate anytime from your "master" file:

Exporting to IFC and other applications

One of the very fundamental things you need when working with BIM is to be able to import and export IFC files. This is still a work in progress in FreeCAD. IFC format is already supported, and importing IFC files into FreeCAD is already pretty reliable. Exporting is still experimental, though, and has currently many limitations. However, things are bettering and we should get proper IFC export very soon.

IFC export requires very little setup, once the necessary software libraries are installed. You only need to recreate the building structure, which is needed in all IFC files, by adding an Arch Building to your file, then an Arch Floor, then moving all the groups of objects that compose your model in it. Make sure you leave your construction geometry (all the 2D stuff we've been drawing) out of it to avoid making your IFC file unnecessarily heavy.

Another thing to set, is to check the "Role" property of structural elements. Since IFC has no "generic" structural element, like FreeCAD, we need to assign them roles (column, beam, etc...) so the exporter knows what element to create in the IFC file.

In this case, we need our whole architectural system, so the IFC exporter can know if an object must be exported as a wall or a column, so we are using our "master" model, not our "output" model.

Once this is done, simply select your building object, and choose the "Industry Foundation Classes" format. Exporting to non-BIM applications, such as Sketchup is also easy, you have several export formats at your disposal, such as Collada, STEP, IGES ou OBJ.

Rendering

FreeCAD also features a rendering module, the Raytracing Workbench. That workbench currently supports two render engines, PovRay and LuxRender. Since FreeCAD is not designed for image rendering, the features that the Raytracing workbench offer to you are somewhat limited. The best course of action when you want to do proper rendering, is to export your model to a mesh-based format such as OBJ or STL, and open it in an application more suited to rendering, such as blender. The image below has been rendered with blender's cycles engine:

But, for a quick rendering, the Raytracing workbench can already do a good job, with the advantage of being very easy to setup, thanks to its templates system. This is a rendering of our model fully made within FreeCAD, with the Luxrender engine, using the "indoor" template.

The Raytracing workbench still offers you very limited control over materials, but lighting and environments are defined in templates, so they can be fully customized.

2D drawings

Certainly the most important use of BIM is to produce 2D drawings automatically. This is done in FreeCAD with the Arch SectionPlane tool. This tool allows you to place a section plane object in the 3D view, that you can orient to produce plans, sections and elevations. Section planes must know what objects they must consider, so once you have created one, you must add objects to it with the Arch Add tool. You can add individual objects, or, more conveniently, a group, a floor or a whole building. This allows you to easily change the scope of a certain section plane later, by adding or removing objects to/from that group. Any change to these objects gets reflected in the views produced by the section plane.

The section plane automatically produces cut views of the objects it intersects. In other words, to produce views instead of sections, you just need to place the section plane outside of your objects.

The section planes can produce two different outputs: shape objects, that live in the same document as your 3D model, or drawing views, that are made to use on a drawing sheet produced by the Drawing workbench. Each of these behave differently, and has its own advantages.

Shape views

This output is produced by using the Draft Shape2DView tool with a section plane selected. You produce a 2D view of the model directly in the 3D space, like on the image above. The main advantage here is that you can work on them using the Draft tools (or any other standard tool of FreeCAD), so you can add texts, dimensions, symbols, etc:

On the image above, two Shape2D views have been produced for each section, one showing everything, the other showing only the cut lines. This allows us to give it a different line weight, and turn hatching on. Then, dimensions, texts and symbols have been added, and a couple of DXF blocks have been imported to represent the furniture. These views are then easy to export to DXF or DWG, and open in your favorite 2D CAD application, such as LibreCAD or DraftSight, where you can work further on them:

Note that some features are still not supported by the DXF/DWG exporter so the result in your 2D application might differ a bit. For example, in the image above, I had to redo the hatching, and correct the position of some dimension texts. If you place your objects in different groups in FreeCAD, these become layers in your 2D CAD application.

Drawing views

The other kind of output that can be produced from section planes is a Drawing view. These are produced by using the Draft Drawing tool with a section plane selected. This method has one big limitation compared to the previous one: you have limited possibilities to edit the results, and at the moment, things like dimensioning or hatching are still not natively supported.

On the other hand, the final output being easier to manipulate, and the graphical possibilities of the SVG format being huge, in the future, undoubtedly this will be the preferred method. At the moment, though, you'll get better results using the previous one.

On the image above, the geometry is the direct output of the section plane, but some other Draft objects have been added, such as dimensions and hatched polygons, and another view object with same scale and offset values has been produced from them with the Draft Drawing tool. In the future, such operations will be done directly on the Drawing page, leaving your model totally clean.

Quantities extraction

This is another very important task to be performed on BIM models. In FreeCAD, things look good right from the start, since the OpenCasCade kernel of FreeCAD already takes care of calculating lengths, areas and volumes for all the shapes it produces. Since all Arch objects are solids, you are always guaranteed to be able to obtain a volume from them.

Using spreadsheets

There is a brand-new workbench in FreeCAD, the Spreadsheet Workbench, that is the perfect tool for collecting such information about our model. It can count objects of a certain name or a certain type, or display a specific properties of those objects. The spreadsheet workbench features two objects: The spreadsheet object is a simple spreadsheet container, that you can edit, and place values inside the cells, but has no automation. The cell controller, on the other hand, is an object that you must insert in a spreadsheet, that controls a series of cells of its host spreadsheet, filling them according to what you specify. This, provided that you organized your model well, allows you to easily retrieve individual values:

Note that the spreadsheet workbench is still very new, and like everything very new, still contains many bugs and limitations. But for simple summaries like this, it already works well. The resulting spreadsheet can then be exported to a CSV file, which can be imported in any spreadsheet application.

The survey mode

Another way to survey your model and extract values, is to use the Arch Survey mode. In this mode, you can click on points, edges, faces or double-click to select whole objects, and you get altitude, length, area or volume values, shown on the model, printed on the FreeCAD output window, and copied to the clipboard, so you can easily pick and paste values in another opened application

Заключение

Надеюсь, это дало Вам хороший обзор доступных инструментов, далее обязательно посмотрите документацию верстаков Arch и Draft (есть немало других инструментов, которые не были упомянуты здесь), и прочую документацию FreeCAD. Нанесите визит так же на форум, многие проблемы обычно могут быть мгновенно решены здесь, и просмотрите в моём блоге новости разработки верстака Arch.

Файл, созданный во время прохождения урока, может быть взят здесь.