Arkusz Blachy: Przykłady
This documentation is not finished. Please help and contribute documentation.
GuiCommand model explains how commands should be documented. Browse Category:UnfinishedDocu to see more incomplete pages like this one. See Category:Command Reference for all commands.
See WikiPages to learn about editing the wiki pages, and go to Help FreeCAD to learn about other ways in which you can contribute.
Wprowadzenie
Środowisko pracy Arkusz Blachy (jest zewnętrznym środowiskiem dostępnym poprzez Menadżer dodatków) stało się bardzo rozbudowane i wymaga odpowiedniej dokumentacji.
Aby uniknąć przepełnienia stron narzędziowych przykładami, dodano tę stronę w celu zebrania części pokazujących i wyjaśniających specjalne możliwości środowiska Arkusz Blachy.
Zaplanowane etapy tworzenia treści:
- Zbieranie zdjęć
- Dodawanie opisów przepływów pracy
- Dodawanie bardziej szczegółowych samouczków
Zawias
Przepływ pracy Zawias: Arkusz Blachy: Dodaj element bazowy, Projekt części: Kieszeń, Projekt Części: Otwór, Arkusz Blachy: Rozwiń.
Zawias - krok po kroku
- Create a profile (a line and a tangent arc), preferably using the Sketcher Workbench.
- Activate the Make Base Wall command to create a BaseBend object.
- Edit the BaseBend object's parameters:
- Set DANEMid Plane to
true
to let the profile extend symmetrically to both sides of the sketch plane. - Set DANEradius and DANEthickness to values of your choice.
- Set DANEMid Plane to
- Create a cut-out contour with the Sketcher Workbench.
- Use the PartDesign Pocket command to cut off one half of the Round bit.
- Create a hole pattern with the Sketcher Workbench.
- Use the PartDesign Hole command. Avoid the countersink and counterbore options to keep the body unfoldable.
- Activate the Unfold command to get an Unfold object.
- Done!
Klips do papieru
Przepływ pracy Klips do papieru: Arkusz Blachy: Dodaj element bazowy, Arkusz Blachy: Szkic na arkuszu, klonowanie, odwracanie i łączenie, Arkusz Blachy: Rozwiń.
Klips do papieru - krok po kroku
- Create a profile, preferably using the Sketcher Workbench on the XZ plane.
- Activate the Make Base Wall command to create a BaseBend object.
- Edit the BaseBend object's parameters in the properties panel:
- Set DANEMid Plane to
true
to let the profile extend symmetrically to both sides of the sketch plane. - Set DANElength to 32 mm.
- Set DANEradius to 2 mm.
- Set DANEthickness to 0.3 mm.
- Set DANEMid Plane to
- Select the face between the round sections and activate the Sketcher Workbench.
- To hide the curled part use the Sketcher View section command.
- Create the cut-out contour.
- Finish the sketch using the Sketcher Leave sketch command.
- Select the face again and add the Cut-out sketch to the selection.
- Use the Sketch on Sheet command to cut around the curled bit.
- One side is finished. We now need to find a way to mirror the body.
Potential mirror options:
- The PartDesign Mirrored command fails because it cannot handle SheetMetal features for some reason. So that does not work.
- The Part Mirror command creates a mirrored part, but this is no longer unfoldable. So that does not work either.
- One way that can work is to use a clone. This still can't be mirrored, but it can use axial symmetry (turn it 180°).
- Another way that works is to use a link object.
Mirror using a clone:
- Select the body from the tree view.
- Use the PartDesign Clone command. It adds a new body containing a clone object.
To apply a 180° turn set the DANEAngle under the Placement property of either the body or the clone to 180°. (Z axis is default and should be fine if you started on the XZ plane as described).
- With the body still active, use the PartDesign Boolean operation command to add the body of the clone and fuse both halves.
- Activate the Unfold command to get an Unfold object.
- Done!
Mirror using a link object:
- Select the body from the tree view.
- Use the Make link command. This adds a new link object.
- Duplicate the link object by setting the property DANEElement Count to 2.
- To apply a 180° turn set the DANEAngle under the Placement property of either of the sub-linked objects to 180°. (Z axis is default and should be fine if you started on the XZ plane as described).
- Select both sub-linked objects in the tree view.
- Activate the Part Fuse command to fuse both halves.
- Activate the Unfold command to get an Unfold object.
- Done!
Klamra Omega
Przepływ pracy Klamra Omega: Arkusz Blachy: Dodaj element bazowy, Projekt Części: Otwór, Projekt Części: Zaokrąglenie, Arkusz Blachy: Rozwiń.
Sześciokątna miska
Przepływ pracy Sześciokątna misa: Arkusz Blachy: Dodaj element bazowy, Arkusz Blachy: Dodaj ścianę, 6x Arkusz Blachy: Dodaj podcięcie w narożniku, Arkusz Blachy: Rozwiń.
Po dodaniu podcięcia narożnego (prawa strona) może być konieczne dostosowanie wartości właściwości Rozmiar.
Klips do długopisu
Przepływ pracy Klips do długopisu: Arkusz Blachy: Dodaj element bazowy, Projekt Części: Kieszeń, 3x Arkusz Blachy: Dodaj ścianę, Arkusz Blachy: Rozwiń.
Przykład przedłużenia ściany
Przepływ pracy Przykład przedłużenia ściany: Arkusz Blachy: Dodaj element bazowy, Arkusz Blachy: Dodaj ścianę, Arkusz Blachy: Wyciągnij, Arkusz Blachy: Wyciągnij, Arkusz Blachy: Rozwiń.
Przy drugim użyciu Wyciągnięcia ściany do kształtu przedłużenia (przedłużeń) używany jest szkic z dwoma konturami, a przy wartości parametru "użyj odjęcia" ustawionej na wartość Prawda
zapewnia on kształt dla wycięć, jak również
Korpus złącza USB
Przepływ pracy Korpus złącza USB: Arkusz Blachy: Dodaj element bazowy, Arkusz Blachy: Wyciągnij, Projekt Części: Kieszeń, Arkusz Blachy: Wyciągnij, Arkusz Blachy: Dodaj ścianę, Arkusz Blachy: Rozwiń.
(Płaskorzeźba jest tylko artystycznym wyrazem tego, co może być ukryte wewnątrz prawdziwej wtyczki).
Właściwości środowiska pracy Arkusz Blachy
W tym rozdziale staramy się wyjaśnić właściwości każdego obiektu środowiska Arkusz Blachy za pomocą prostych obrazków, jeśli to możliwe.
Obiekt bazowy wyginania
Wybrany szkic + Arkusz Blachy: Dodaj element bazowy → Obiekt bazowy wyginania z domyślnymi nastawami
Edit DANElength: Default length → Reduced length
Switch DANEMid Plane from false
to true
: Extrusion in one direction → Symmetric extrusion
Switch DANEReverse from false
to true
: Default direction → Inverted direction
Select DANEBend Side: Outside
(default) → Inside
→ Middle
Edit DANEradius: Default radius → Enlarged radius.
This property is the inner radius of the bends created at the vertices where two edges in the sketch have a non-tangential transition.
Edit DANEthickness: Default Thickness → Enlarged thickness
Obiekt wyginania
Obiekt Wyginania składa się z zestawów składających się z jednego cylindrycznego zgięcia i jednego płaskiego paska. Każda para rozciąga się od wybranej krawędzi półfabrykatu.
Selected edges +
Make Wall
→ Bend objects with default settings
(Two Bend objects in two separate bodies.)
Edit DANEradius to vary the inner radius of all bends supplied by a Bend object. (See BaseBend object above)
Edit DANElength to vary the length of all planar strips extending from the bends of a Bend object.
- Don't confuse the DANElength with a flange length which is the sum of this length, radius, and thickness (90° only).
Switch DANEinvert from false
to true
:Default flanges (Bend objects) → Inverted flanges
Edit DANEangle:Default angle (90°) → Enlarged angle → Decreased angle
We don't have to care about trimming the edges, because Auto Miter is activated by default.
If deactivated, the result would look like this:
Switch DANEAuto Miter from true
to false
: Default angle (90°) → Enlarged angle → Decreased angle
(Auto Miter has no effect on single flanges)
To manually miter a flange edge miterangle1 and miterangle2 are used:
Edit DANEmiterangle1 and DANEmiterangle2: No miter (default) → Differently mitered edges, positive angle → Symmetrically mitered edges, negative angles
Mitering only effects the planar strips, not the bends.
- (It takes the whole edge into account and so cannot be used to chamfer flange edges)
To display the different choices of Bend Type we introduce an auxiliary cuboid that extrudes from the same outline as the blank and has the same height as the Bend object (its flange length).
Select DANEBend Type: Material Outside
(default) → Material Inside
→ Thickness Outside
→ Offset
- Outside: The bend starts at the selected edge (The whole Bend object lies outside the cuboid).
- Inside: The outer side of the bend ends on the cuboid surface (The whole Bend object lies inside the cuboid).
- Thickness Outside: The inner side of the bend ends on the cuboid surface (only the planar strip is protruding from the cuboid surface).
- Offset: According to the value of DANEoffset the bend is moved in outward direction from its default position.
- An extension is inserted for positive values (high-lighted strip).
- Negative values are allowed to move the bend inwards.
If we don't want to use the whole length of an edge we can use gap1 and gap2.
Edit DANEgap1 and DANEgap2: Default flanges → Flanges with different values for gap1 and gap2
If the length of a gap reaches or extends the value of DANEmin Relief Gap, a relief will be added to the gap.
Reliefs are controlled by DANErelief Type, DANEreliefd (relief depth), and DANEreliefw (relief width) which are enabled only when a gap value is set.
Edit DANEreliefd and DANEreliefw: Default values → Relief depth enlarged → Relief depth and width enlarged
Switch DANErelief Type from Rectangle
to Round
: Default rectangular relief → Round relief
The round option will only be applied, if the relief depth is larger than the relief width.
Switch DANEUse Relief Factor from false
(default) to true
to set the values of DANEreliefd and DANEreliefw automatically. Both are set to the object's (inherited) thickness multiplied by the value of DANERelief Factor.
- In this case the round option is useless, since the relief depth is as large as the relief width. (See above)
A new property DANELength Spec introduced in version 1.0 enables us to choose how to measure the length of the Bend object:
Side view of four 120° flanges with default length (10 mm) and different DANELength Spec values:
Leg
(default), Outer Sharp
, Inner Sharp
, Tangential
With the Tangential
option selected the property DANElength is the equivalent of the flange length.
Outer Sharp
and Tangential
are identical for 90° angles.