Draft Constrain/sv: Difference between revisions

From FreeCAD Documentation
(Created page with "Category:User Documentation/sv")
(Updating to match new version of source page)
 
(13 intermediate revisions by the same user not shown)
Line 1: Line 1:
<languages/>

{{Docnav
|[[Draft_Snap|Snap]]
|[[Draft_Pattern|Pattern]]
|[[Draft_Workbench|Draft]]
|IconL=
|IconR=
|IconC=Workbench_Draft.svg
}}

{{TOCright}}

== Description ==

<div class="mw-translate-fuzzy">
För att använda begränsning, tryck på {{KEY|SKIFT}} medan du ritar.
För att använda begränsning, tryck på {{KEY|SKIFT}} medan du ritar.
</div>


Constraining is available with most [[Draft_Workbench|Draft]] and [[Arch_Workbench|Arch]] commands.
[[Image:Draft_Constrain_example.jpg]]


[[Image:Draft_Constrain_taskpanel_example.png]]
I alla verktyg som stöder begränsning, så kan du tvinga nästa punkt att begränsas horisontellt eller vertikalt i relation till den sist inmatade punkten. Den vertikala eller horisontella begränsningen beror på var musmarkören är när du trycker på {{KEY|SKIFT}}. Om du är norr eller söder om den sista punkten, så kommer begränsningen att bli vertikal. Om du är mer åt öster eller väster, så kommer den att bli horisontal. för att ändra, släpp {{KEY|SKIFT}} och tryck ned igen när musmarkören har en annan position.
{{Caption|While the cursor is constrained the task panel locks the values that are not being modified}}


== Usage horizontal and vertical constraints ==
En del verktyg, som [[Draft_Offset/sv|offset]] och [[Draft_Trimex/sv|trimex]] använder begränsning på ett annorlunda sätt. De begränsar inte vertikalt eller horisontellt utan använder ett annat sätt som är mer anpassat för just det verktyget, som till exempel att begränsa operationen till ett visst polyline segment.


# Choose a [[Draft_Workbench|Draft]] or [[Arch_Workbench|Arch]] command to create your geometry.
# Pick a first point. A previous point is required.
# Do one of the following:
#* For a horizontal constraint: move the cursor to the left or right of the previous point.
#* For a vertical constraint: move the cursor above or below the previous point.
# Hold down {{KEY|Shift}}.
# The cursor is now constrained.
# Pick the next point.
# If the command is still active: optionally release {{KEY|Shift}} to disable the constraint.
# Always release {{KEY|Shift}} when the command is finished.

== Usage X, Y and Z constraints ==

# Choose a [[Draft_Workbench|Draft]] or [[Arch_Workbench|Arch]] command to create your geometry.
# Pick a first point. A previous point is required.
# Press {{KEY|X}}, {{KEY|Y}} or {{KEY|Z}} to specify the direction.
# The cursor is now constrained.
# Pick the next point.
# If the command is still active optionally do one of the following:
#* Press the same key to disable the constraint.
#* Press one of the two other keys to constrain in a different direction.
# X, Y and Z constraints are automatically disabled when the command is finished.

== Notes ==

* Constraining can be combined with [[Draft_Snap|snapping]].
* The [[Draft_Offset|Draft Offset]] command and [[Draft_Trimex|Draft Trimex]] command use a different type of constraining, namely to restrict the operation to a certain segment.

== Preferences ==

See also: [[Preferences_Editor|Preferences Editor]] and [[Draft_Preferences|Draft Preferences]].

* The default {{MenuCommand|Constrain modifier}} key, {{KEY|Shift}}, can be changed: {{MenuCommand|Edit → Preferences... → Draft → Grid and snapping → Constrain modifier}}.
* The {{MenuCommand|X}}, {{MenuCommand|Y}} and {{MenuCommand|Z}} shortcuts can be changed: {{MenuCommand|Edit → Preferences... → Draft → Interface → In-command shortcuts}}.


<div class="mw-translate-fuzzy">
[[Category:User Documentation/sv]]
[[Category:User Documentation/sv]]
</div>


{{Draft Tools navi{{#translation:}}}}
{{Userdocnavi{{#translation:}}}}
{{clear}}
{{clear}}
<languages/>

Latest revision as of 20:04, 7 December 2023

Description

För att använda begränsning, tryck på SKIFT medan du ritar.

Constraining is available with most Draft and Arch commands.

While the cursor is constrained the task panel locks the values that are not being modified

Usage horizontal and vertical constraints

  1. Choose a Draft or Arch command to create your geometry.
  2. Pick a first point. A previous point is required.
  3. Do one of the following:
    • For a horizontal constraint: move the cursor to the left or right of the previous point.
    • For a vertical constraint: move the cursor above or below the previous point.
  4. Hold down Shift.
  5. The cursor is now constrained.
  6. Pick the next point.
  7. If the command is still active: optionally release Shift to disable the constraint.
  8. Always release Shift when the command is finished.

Usage X, Y and Z constraints

  1. Choose a Draft or Arch command to create your geometry.
  2. Pick a first point. A previous point is required.
  3. Press X, Y or Z to specify the direction.
  4. The cursor is now constrained.
  5. Pick the next point.
  6. If the command is still active optionally do one of the following:
    • Press the same key to disable the constraint.
    • Press one of the two other keys to constrain in a different direction.
  7. X, Y and Z constraints are automatically disabled when the command is finished.

Notes

  • Constraining can be combined with snapping.
  • The Draft Offset command and Draft Trimex command use a different type of constraining, namely to restrict the operation to a certain segment.

Preferences

See also: Preferences Editor and Draft Preferences.

  • The default Constrain modifier key, Shift, can be changed: Edit → Preferences... → Draft → Grid and snapping → Constrain modifier.
  • The X, Y and Z shortcuts can be changed: Edit → Preferences... → Draft → Interface → In-command shortcuts.