PartDesign PolaresMuster

From FreeCAD Documentation
Revision as of 02:59, 27 November 2018 by Normandc (talk | contribs) (Created page with "====Referenz auswählen...====")

PartDesign Polares Muster

Menüeintrag
PartDesign → Polares Muster
Arbeitsbereich
PartDesign
Standardtastenkürzel
Keiner
Eingeführt in Version
-
Siehe auch
Keiner

Beschreibung

Dieses Werkzeug verwendet ein ausgewähltes Formelement und erstellt daraus eine Reihe von (um eine ausgewählte Achse) gedrehten Kopien. Das resultierende Objekt wird als neues separates Objekt in der Baumansicht erstellt.

Above: a slot-shaped pocket (B) made on top of a base solid (A, also referred to as support) is used for a polar pattern. The result (C) is shown on the right.

Anwendung

  1. Select the feature(s) to be patterned. Alternatively, the feature can be selected from a dialogue after step 2.
    v0.16 and below Only a single feature can be selected, and it must be the last one at the bottom of the feature tree.
  2. Press the PolarPattern button.
  3. v0.17 and above Press Add feature to add a feature to be patterned. The feature must be visible in the 3D view:
    1. Switch to the Model tree;
    2. Select in the tree the feature to be added and press spacebar to make it visible in the 3D view;
    3. Switch back to the Tasks panel;
    4. Select the feature in the 3D view; it will be added to the list.
    5. Repeat to add other features.
  4. v0.17 and above Press Remove feature to remove a feature from the list, or right-click on the feature in the list and select Remove.
  5. Define the axis. See Options.
  6. Define the angle between the last copied occurrence and the original feature.
  7. Set the number of occurrences.
  8. Press OK.

Optionen

Axis

Beim Erstellen eines Polaren Form-Musters bietet der Dialog "Polardiagramm-Parameter" verschiedene Möglichkeiten zum Festlegen der Pattern-Rotationsachse.

Normale Skizzenachse

Eine Achse, die normal zur Skizze ist und im Ursprung der Skizze des verwendeten Merkmals beginnt, wird als Achse für das polare Muster genommen.
Die Drehrichtung des Musters kann umgekehrt werden, indem Sie auf "Richtung umkehren" klicken.

Horizontale Skizzenachse

Uses the horizontal axis of the sketch for axis.

Vertikale Skizzenachse

Uses the vertical axis of the sketch for axis.

Individuelle Achse in der Skizze

Wenn die Skizze für das zu wiederholende Muster Konstruktionsliniem besitzen, werden diese Konstruktionslinien in dem Dropdown-MenüI als jeweils spezielle Achsen aufgelistet. Die erste Konstruktionslinie wird im Menü als Konstruktionslinie 1 aufgelistet.

Basis (X/Y/Z) Achse

v0.17 und höher Die Standardachsen des Koordinatensystems des Körpers (Body) stehen als Basis X, Y oder Z-Richtung zur Verfügung.

Referenz auswählen...

Allows you to select either a DatumLine or an edge of an object or a line of a sketch to use for axis.

Winkel und Vorkommen

Gibt den Winkel an, der vom Muster abgedeckt werden soll, sowie die Gesamtzahl der Musterformen (einschließlich des ursprünglichen Elements). Zum Beispiel würden vier Vorkommen in einem Winkel von 180 Grad einen Abstand von 60 Grad zwischen Mustern ergeben. Es gibt eine Ausnahme: Wenn der Winkel 360 Grad beträgt werden z.b vier Vorkommen um 90 Grad voneinander getrennt, weil das erste und das letzte Vorkommen identisch sind.

Beschränkungen