Reinforcement UShapeRebar: Difference between revisions
({{Button}} instead of {{KEY}} template; this command available with the addon manager; image caption, translate tags in correct position) |
({{Button}} instead of {{KEY}} template; image caption) |
||
Line 25: | Line 25: | ||
<!--T:6--> |
<!--T:6--> |
||
# Create a [[Arch Structure|structure]] element |
# Create a [[Arch Structure|structure]] element. |
||
# Select any face of the structure |
# Select any face of the structure. |
||
# Then select {{ |
# Then select {{Button|[[Image:UShapeRebar.png|16px]] UShape Rebar}} from the rebar tools. |
||
# A task panel will pop-out on the left side of the screen as shown below |
# A task panel will pop-out on the left side of the screen as shown below. |
||
# Select the desired orientation |
# Select the desired orientation. |
||
# Give the inputs like front cover, right side cover, left side cover, bottom cover, top cover, rounding factor and diameter of the rebar |
# Give the inputs like front cover, right side cover, left side cover, bottom cover, top cover, rounding factor and diameter of the rebar. |
||
# Select the mode of distribution either amount or spacing |
# Select the mode of distribution either amount or spacing. |
||
# If spacing is selected, a user can also opt for [[Custom_Spacing|custom spacing]] |
# If spacing is selected, a user can also opt for [[Custom_Spacing|custom spacing]]. |
||
# Pick selected face is used to verify or change the face for rebar distribution |
# Pick selected face is used to verify or change the face for rebar distribution. |
||
# Click {{ |
# Click {{Button|OK}} or {{Button|Apply}} to generate the rebars. |
||
# Click {{ |
# Click {{Button|Cancel}} to exit the task panel. |
||
[[Image:UShapeDialog.png|250px]] |
|||
{{Caption|Taskview panel for the Arch Rebar UShape tool}} |
|||
==Properties== <!--T:7--> |
==Properties== <!--T:7--> |
Revision as of 22:29, 27 November 2018
Arch Rebar UShape |
Menu location |
---|
Arch → Rebar tools |
Workbenches |
Arch, BIM |
Default shortcut |
None |
Introduced in version |
- |
See also |
LShape Rebar, Arch Rebar |
Description
The UShape Rebar tool allows user to create a UShape reinforcing bar in the structural element.
This command is part of the Reinforcement Addon, that you can install with the Addon Manager, via the menu Tools → Addon manager → Reinforcement.
U-shaped reinforcement bars inside a structural element
How to use
- Create a structure element.
- Select any face of the structure.
- Then select UShape Rebar from the rebar tools.
- A task panel will pop-out on the left side of the screen as shown below.
- Select the desired orientation.
- Give the inputs like front cover, right side cover, left side cover, bottom cover, top cover, rounding factor and diameter of the rebar.
- Select the mode of distribution either amount or spacing.
- If spacing is selected, a user can also opt for custom spacing.
- Pick selected face is used to verify or change the face for rebar distribution.
- Click OK or Apply to generate the rebars.
- Click Cancel to exit the task panel.
Taskview panel for the Arch Rebar UShape tool
Properties
- DataOrientation: It decides the orientation of the rebar (like a bottom, top, right and left).
- DataFront Cover: The distance between rebar and selected face.
- DataRight Cover: The distance between the right end of the rebar to right face of the structure.
- DataLeft Cover: The distance between the left end of the rebar to the left face of the structure.
- DataBottom Cover: The distance between rebar from the bottom face of the structure.
- DataTop Cover: The distance between rebar from the top face of the structure.
- DataRounding: A rounding value to be applied to the corners of the bars, expressed in times the diameter.
- DataAmount: The amount of rebars.
- DataSpacing: The distance between the axes of each bar.
Scripting
The UShape Rebar tool can by used in macros and from the python console by using the following function:
makeUShapeRebar(FrontCover, BottomCover, RightCover, LeftCover, Diameter, Topcover, Rounding, AmountSpacingCheck, AmountSpacingValue, Orientation, Structure, Facename)
- The UShape Rebar have four different orientations:
- Bottom
- Top
- Right
- Left
- Adds a UShape reinforcing bar object to the given structural object.
- If no Structure and Facename is given, it will take user selected face as input.
- Returns the new Rebar object.
Example: Creating UShape rebar.
import Arch, UShapeRebar
structure = Arch.makeStructure(length=1000.0, width=1000.0, height=400.0)
structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()
rebar = UShapeRebar.makeUShapeRebar(20, 20, 20, 20, 8, 20, 4, True, 10, "Bottom", structure, "Face1")
Changing properties of UShape rebar.
import UShapeRebar
UShapeRebar.editUShapeRebar(rebar, 25, 25, 25, 25, 16, 25, 2, True, 15, "Top")