PartDesign SubtractiveEllipsoid/es: Difference between revisions

From FreeCAD Documentation
(Created page with "Tras su creación, el Elipsoide puede ser editado de dos maneras: * Haciendo doble clic con el ratón sobre el árbol del Modelo, o pinchando con el botón derecho y seleccion...")
(Created page with "==Propiedades==")
Line 39: Line 39:
* Por medio del [[Property_editor/es|Editor de propiedades]].
* Por medio del [[Property_editor/es|Editor de propiedades]].


==Properties==
==Propiedades==


* {{PropertyData|Attachment}}: defines the attachment mode as well as the Attachment Offset. See [[Part_Attachment|Part Attachment]].
* {{PropertyData|Attachment}}: defines the attachment mode as well as the Attachment Offset. See [[Part_Attachment|Part Attachment]].

Revision as of 15:59, 31 May 2021

PartDesign Elipsoide Sustractivo

Ubicación en el Menú
Part Design → Crear una primitiva sustractiva → Elipsoide sustractivo
Entornos de trabajo
PartDesign
Atajo de teclado por defecto
Ninguno
Introducido en versión
0.17
Ver también
Ninguno

Descripción

Inserta un Elipsoide sustractivo en el Body (cuerpo) activo. Su forma es sustraída del sólido existente.

A la izquierda: Body activo (A) mostrado en color gris y el Elipsoide sustractivo (B) mostrado en color rojo transparente. El resultado se puede apreciar a la derecha.

Uso

  1. Presionar el botón Elipsoide Sustractivo . Nota: El Elipsoide sustractivo forma parte de un icono de herramientas llamado Crear una primitiva sustractiva. Tras abrir FreeCAD, la Caja sustractiva es la única mostrada en la barra de herramientas. Para obtener el Elipsoide, pinchar en la flecha que indica hacia abajo que está al lado del icono visible y seleccionar Elipsoide sustractivo en el menú desplegable.
  2. Seleccionar los parámetros de la primitiva y el Attachment.
  3. Aceptar OK.
  4. Una operación de Elipsoide aparece dentro del Body(cuerpo) activo.

Opciones

Tras su creación, el Elipsoide puede ser editado de dos maneras:

  • Haciendo doble clic con el ratón sobre el árbol del Modelo, o pinchando con el botón derecho y seleccionando Editar primitiva en el menú contextual. Con ello se abre la ventana de selección de parámetros de la Primitiva.
  • Por medio del Editor de propiedades.

Propiedades

  • DatosAttachment: defines the attachment mode as well as the Attachment Offset. See Part Attachment.
  • DatosLabel: label given to the Ellipsoid object. Change to suit your needs.
  • DatosRadius1: the radius value along the ellipsoid's vertical axis; by default, parallel to the Z-axis.
  • DatosRadius2: the radius value along the ellipsoid's length; by default, parallel to the X-axis.
  • DatosRadius3: the radius value along the ellipsoid's width; by default, parallel to the Y-axis. At the default value of zero, the ellipsoid forms an oblate spheroid.
  • DatosAngle1: (labelled V parameter in the Primitive parameters) lower truncation of the ellipsoid, parallel to the circular cross section (-90 degrees in a full spheroid)
  • DatosAngle2: (unlabelled in the Primitive parameters) upper truncation of the ellipsoid, parallel to the circular cross section (90 degrees in a full spheroid).
  • DatosAngle3: (labelled U parameter in the Primitive parameters) angle of rotation of the elliptical cross section (360 degrees in a full spheroid).