Sketcher CreatePolyline/ro: Difference between revisions

From FreeCAD Documentation
(Created page with "== Cum se folosește ==")
(Created page with "Polilinia începe întotdeauna cu un segment de linie dreaptă: faceți clic pe - mutați clic pe mouse. Mutați mouse-ul din nou. După plasarea segmentului de primă linie,...")
Line 14: Line 14:




Polilinia începe întotdeauna cu un segment de linie dreaptă: faceți clic pe - mutați clic pe mouse. Mutați mouse-ul din nou. După plasarea segmentului de primă linie, instrumentul de polilinie Sketcher are mai multe moduri care pot fi comutate cu tasta {{KEY|M}}. De exemplu, puteți desena arce tangente sau perpendiculare după o linie sau un segment de arc. Apăsarea repetată a tastei {{KEY | M}} comută prin aceste moduri diferite:
The polyline always starts with a straight line segment: click - move the mouse - click. Move the mouse again. After placing the first line segment, the Sketcher polyline tool has multiple modes that can be toggled with the {{KEY|M}} key. For example you can draw tangent or perpendicular arcs following a line or arc segment. Repeatedly pressing the {{KEY|M}} key toggles through these different modes:


# Press the {{KEY|M}} key: the new segment is a line which is perpendicular to the previous segment.
# Press the {{KEY|M}} key: the new segment is a line which is perpendicular to the previous segment.

Revision as of 09:26, 4 November 2018

Sketcher CreatePolyline

poziția meniului
Sketch → Sketcher geometries → Create polyline
Ateliere
Sketcher
scurtătură
nici unul
Prezentat în versiune
-
A se vedea, de asemenea,
Sketcher Line

Descriere

Această unealtă funcționează ca un instrument Sketcher Line, dar crează linii și arce de cerc conectate prin vârfuri/vertex-uri. Când pornește instrumentul, indicatorul mouse se modifică într-o cruce albă și o iconiță roșie tip polilinie. coordonatele indicatorului sunt afișate alături în albastru și în timp real.

Polyline începe cu o linie, un arc de cerc tangent, un arc de cerc perpendicular și apoi cu o linie tangentă

Cum se folosește

Polilinia începe întotdeauna cu un segment de linie dreaptă: faceți clic pe - mutați clic pe mouse. Mutați mouse-ul din nou. După plasarea segmentului de primă linie, instrumentul de polilinie Sketcher are mai multe moduri care pot fi comutate cu tasta M. De exemplu, puteți desena arce tangente sau perpendiculare după o linie sau un segment de arc. Apăsarea repetată a tastei M comută prin aceste moduri diferite:

  1. Press the M key: the new segment is a line which is perpendicular to the previous segment.
  2. Press the M key again: the new segment is a line which is tangential to the previous segment.
  3. Press the M key again: the new segment is an arc which is tangential to the previous segment.
  4. Press the M key again: the new segment is an arc which is perpendicular (left) to the previous segment.
  5. Press the M key again: the new segment is an arc which is perpendicular(right) to the previous segment.
  6. Press the M key again: You are again in the state where you started; the line is only connected with a coincidence to the previous segment.
  • v0.18 and above While in any of the arc modes, holding down the Ctrl key (MacOS: CMD key) and moving the cursor causes the arc to snap by increments of 45 degrees, relative to the previously created polyline segment.
  • Pick points on an empty area of the 3D view, or on an existing object (auto constraints must be active in TaskView).
  • Pressing Esc or clicking the right mouse button before closing the polyline to a loop ends the current polyline and you can continue with a new one. Pressing Esc or clicking the right mouse button again ends the polyline function.
  • Pressing Esc or clicking the right mouse button after closing the polyline to a loop ends the polyline function.