Draft Circle/es: Difference between revisions

From FreeCAD Documentation
(Created page with "{{GuiCommand/es|Name=Draft_Circle|Workbenches=Croquis, Arquitectura|MenuLocation=Boceto → Circunferencia|Shortcut=C I|SeeAlso=[[Draft ...")
(Created page with "====Descripción==== La herramienta Circunferencia crea una circunferencia en el plano de trabajo actual introduciendo dos puntos, el centro y el ra...")
Line 1: Line 1:
{{GuiCommand/es|Name=Draft_Circle|Workbenches=[[Draft Module/es|Croquis]], [[Arch Module/es|Arquitectura]]|MenuLocation=Boceto → Circunferencia|Shortcut=C I|SeeAlso=[[Draft Arc/es|Arco]]}}
{{GuiCommand/es|Name=Draft_Circle|Workbenches=[[Draft Module/es|Croquis]], [[Arch Module/es|Arquitectura]]|MenuLocation=Boceto → Circunferencia|Shortcut=C I|SeeAlso=[[Draft Arc/es|Arco]]}}


====Descripción====
==Description==

The Circle tool creates a circle in the current [[Draft Workingplane|work plane]] by entering two points, the center and the radius, or by picking tangents, or any combination of those. It takes the [[Draft Linestyle|linewidth and color]] previously set on the Tasks tab. This tool works the same way as the [[Draft Arc]] tool, except that it stops after entering the radius.
La herramienta Circunferencia crea una circunferencia en el [[Draft Workingplane/es|plano de trabajo]] actual introduciendo dos puntos, el centro y el radio, o seleccionando las tangentes o cualquier combinación de ellas. Toma el [[Draft Linestyle/es|espesor de línea y color]] previamente establecido en la pestaña de tareas. Esta herramienta funciona del mismo modo que la herramienta [[Draft Arc/es|Arco]], excepto que termina después de introducir el radio.


[[Image:Draft_Circle_example.jpg|400px]]
[[Image:Draft_Circle_example.jpg|400px]]

Revision as of 18:17, 9 January 2014

Draft_Circle

Ubicación en el Menú
Boceto → Circunferencia
Entornos de trabajo
Croquis, Arquitectura
Atajo de teclado por defecto
C I
Introducido en versión
-
Ver también
Arco

Descripción

La herramienta Circunferencia crea una circunferencia en el plano de trabajo actual introduciendo dos puntos, el centro y el radio, o seleccionando las tangentes o cualquier combinación de ellas. Toma el espesor de línea y color previamente establecido en la pestaña de tareas. Esta herramienta funciona del mismo modo que la herramienta Arco, excepto que termina después de introducir el radio.

How to use

  1. Press the Draft Circle button, or press C then I keys
  2. Click a first point on the 3D view, or type a coordinate
  3. Click a second point on the 3D view, or enter a radius value.

Options

  • The primary use of the circle tool is by picking two points, the centre and a point on the circumference, defining the radius.
  • By pressing ALT, you can select a tangent instead of picking a point. You can therefore construct several types of circles by selecting one, two or three tangents.
  • To enter coordinates manually, simply enter the numbers, then press ENTER between each X, Y and Z component.
  • Press T or click the checkbox to check/uncheck the Continue button. If continue mode is on, the Circle tool will restart after you give the second point, allowing you to draw another circle without pressing the Circle button again.
  • Press CTRL while drawing to force snapping your point to the nearest snap location, independently of the distance.
  • Press SHIFT while drawing to constrain your second point horizontally or vertically in relation to the first one.
  • Press I or the Filled button to have the circle to appear as a face after it has been closed. This simply sets the View->Property of the Circle to "Flat lines" or "Wireframe", so it can easily be changed later.
  • Press ESC or the Cancel button to abort the current Line command.
  • The circle can be turned into an arc after creation, by setting its first angle and last angle properties to different values.

Properties

  • DatosRadius: The radius of the circle

Scripting

The Circle tool can by used in macros and from the python console by using the following function:

 '''makeCircle (radius, [placement], [facemode], [startangle], [endangle])'''
  • Creates a circle object with given radius.
  • If a placement is given, it is used.
  • If facemode is False, the circle is shown as a wireframe, otherwise as a face.
  • If startangle AND endangle are given (in degrees), they are used and the object appears as an arc.
  • Returns the newly created object.

Example:

 import Draft
 myCircle = Draft.makeCircle(2)