Draft BSpline/it: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
No edit summary
Line 1: Line 1:
{{GuiCommand/it|Name=Draft BSpline|Name/it=BSpline|Workbenches=[[Draft Module/it|Draft]], [[Arch Module/it|Architettura]]|MenuLocation=Draft → BSpline |Shortcut=B S|SeeAlso=[[Draft Wire/it|DWire]]}}
{{GuiCommand/it|Name=Draft BSpline|Name/it=BSpline|Workbenches=[[Draft Module/it|Draft]], [[Arch Module/it|Architettura]]|MenuLocation=Draft → BSpline |Shortcut=B S|SeeAlso=[[Draft Wire/it|DWire]]}}


Crea una [http://en.wikipedia.org/wiki/B-spline curva B-Spline], una linea flessibile, passante per i punti selezionati nel [[Draft Workingplane/it|piano di lavoro]] corrente. La BSpline assume [[Draft Linestyle/it|il tipo di linea e il colore]] impostati in precedenza nella Barra dei comandi e modificabili tramite la stessa o nella scheda Vista combinata → Proprietà → Vista. Lo strumento BSpline si comporta esattamente come lo strumento [[Draft Wire/it|DWire]].
Crea una [http://en.wikipedia.org/wiki/B-spline curva B-Spline], una linea flessibile, passante per i punti selezionati nel [[Draft SelectPlane/it|piano di lavoro]] corrente. La BSpline assume [[Draft Linestyle/it|il tipo di linea e il colore]] impostati in precedenza nella Barra dei comandi e modificabili tramite la stessa o nella scheda Vista combinata → Proprietà → Vista. Lo strumento BSpline si comporta esattamente come lo strumento [[Draft Wire/it|DWire]].


[[Image:Draft_bspline_example.jpg|400px]]
[[Image:Draft_bspline_example.jpg|400px]]
Line 13: Line 13:
# Premere {{KEY/it|F}} o {{KEY/it|C}}, o fare doppio clic sull'ultimo punto, oppure fare clic sul primo punto per completare o chiudere la BSpline. La spline chiusa è anche una faccia, nonostante appaia come reticolo.
# Premere {{KEY/it|F}} o {{KEY/it|C}}, o fare doppio clic sull'ultimo punto, oppure fare clic sul primo punto per completare o chiudere la BSpline. La spline chiusa è anche una faccia, nonostante appaia come reticolo.


=== Opzioni ===
==Options==
* Press {{KEY|F}} or the {{KEY|[[Image:Draft FinishLine.png|12px]] '''[[Draft_FinishLine|Finish]]'''}} button to finish the spline, leaving it open

* Premere {{KEY/it|F}} o premere {{KEY/it|[[Image:Draft FinishLine.png|12px]] [[Draft_FinishLine/it|Termina]]}} per interrompere il disegno della BSpline, lasciandola aperta
* Press {{KEY|C}} or the {{KEY|[[Image:Draft CloseLine.png|12px]] '''[[Draft_CloseLine|Close]]'''}} button or click on the first point to finish the spline, but making it closed by adding a last segment between the last point and the first one.
* Press {{KEY|X}}, {{KEY|Y}} or {{KEY|Z}} after a point to constrain the next point on the given axis.
* Premere {{KEY/it|C}} o il pulsante {{KEY/it|[[Image:Draft CloseLine.png|12px]] [[Draft_CloseLine/it|Chiudi]]}} o fare clic sul primo punto per chiudere la spline collegando con un tratto l'ultimo punto e il primo.
* To enter coordinates manually, simply enter the numbers, then press {{KEY|ENTER}} between each X, Y and Z component.
* Premere {{KEY/it|X}}, {{KEY/it|Y}} o {{KEY/it|Z}} dopo un punto per vincolare il punto successivo sul corrispondente asse.
* Press {{KEY|R}} or click the checkbox to check/uncheck the {{KEY|'''Relative'''}} button. If relative mode is on, the coordinates of the next point are relative to the last one. If not, they are absolute, taken from the (0,0,0) origin point.
* Per inserire manualmente le coordinate, è sufficiente inserire il loro valore, poi premere {{KEY/it|INVIO}} per ogni componente X, Y e Z. E' bene tenere il puntatore del mouse fuori dall'area di lavoro in quanto un suo movimento accidentale cattura e inserisce nel campo di input le coordinate a cui si trova e costringe a ripetere l'inserimento.
* Press {{KEY|T}} or click the checkbox to check/uncheck the {{KEY|'''Continue'''}} button. If continue mode is on, the BSpline tool will restart after you finish or close it, allowing you to draw another one without pressing the BSpline button again.
* Premere {{KEY/it|R}} oppure fare clic sulla casella di controllo per selezionare o deselezionare la modalità {{KEY/it|Relativo}}. In modalità '''Relativo''', le coordinate del secondo punto sono relative al primo. In caso contrario, sono assolute, a partire dal punto di origine (0,0,0).
* Press {{KEY|CTRL}} while drawing to force [[Draft_Snap|snapping]] your point to the nearest snap location, independently of the distance.
* Premere {{KEY/it|T}} oppure fare clic sulla casella di controllo per selezionare o deselezionare la modalità {{KEY/it|Continua}}. In modalità '''Continua''', al termine dell'operazione, lo strumento BSpline si riavvia automaticamente e permette di disegnare una nuova BSpline senza dover ripetere il comando.
* Press {{KEY|SHIFT}} while drawing to [[Draft_Constrain|constrain]] your next point horizontally or vertically in relation to the last one.
* Premere {{KEY/it|CTRL}} mentre si disegna per [[Draft_Snap/it|ancorare]] il proprio punto al punto agganciabile più vicino, indipendentemente dalla distanza.
* Press {{KEY|W}} or press the {{KEY|[[Image:Draft Wipe.png|12px]] '''Wipe'''}} button to remove the existing segments and start the spline from the last point.
* Premere {{KEY/it|SHIFT}} mentre si disegna per [[Draft_Constrain/it|vincolare]] orizzontalmente o verticalmente il secondo punto rispetto al primo.
* Premere {{KEY/it|W}} o il pulsante {{KEY/it|[[Image:Draft Wipe.png|12px]] Pulisci}} per rimuovere i segmenti esistenti e avviare la spline dall'ultimo punto definito.
* Press {{KEY|CTRL}}+{{KEY|Z}} or press the {{KEY|[[Image:Draft UndoLine.png|12px]] '''[[Draft_UndoLine|Undo]]'''}} button to undo the last point.
* Press {{KEY|I}} or the {{KEY|'''Filled'''}} button to have the spline to appear as a face after it has been closed. This simply sets the View->Property of the Wire to "Flat lines" or "Wireframe", so it can easily be changed later.
* Premere {{KEY/it|CTRL}}+{{KEY/it|Z}} o premere il pulsante {{KEY/it|[[Image:Draft UndoLine.png|12px]] [[Draft_UndoLine|Annulla]]}} per annullare l'ultimo punto inserito. Questa opzione permette di annullare a ritroso i punti di una BSpline.
* Press {{KEY|ESC}} or the {{KEY|'''Cancel'''}} button to abort the current BSpline command.
* Premere {{KEY/it|I}} o il pulsante {{KEY/it|Pieno}} per visualizzare la bspline come una faccia dopo che essa è stata chiusa. Questo comando imposta semplicemente la Proprietà → Vista → Display mode della bspline come Flat lines, Shaded, Wireframe o Point e in seguito può essere modificata facilmente.
* BSplines, when in "Flat Lines" display mode, can display a hatch pattern, by setting their "Pattern" property below.
* Premere {{KEY/it|ESC}} o premere il pulsante {{KEY/it|Cancella}} per uscire dal comando attivo.


==Properties==
==Properties==

Revision as of 18:46, 31 May 2014

BSpline

Posizione nel menu
Draft → BSpline
Ambiente
Draft, Architettura
Avvio veloce
B S
Introdotto nella versione
-
Vedere anche
DWire

Crea una curva B-Spline, una linea flessibile, passante per i punti selezionati nel piano di lavoro corrente. La BSpline assume il tipo di linea e il colore impostati in precedenza nella Barra dei comandi e modificabili tramite la stessa o nella scheda Vista combinata → Proprietà → Vista. Lo strumento BSpline si comporta esattamente come lo strumento DWire.

Utilizzo

  1. Premere il pulsante Template:KEY/it, o premere i tasti Template:KEY/it e Template:KEY/it
  2. Selezionare un primo punto nella vista 3D oppure digitare le sue coordinate
  3. Selezionare un nuovo punto della vista 3D, o digitare le sue coordinate
  4. Tra due punti traccia un segmento, quindi, per ottenere una curva, inserire un terzo punto
  5. Premere Template:KEY/it o Template:KEY/it, o fare doppio clic sull'ultimo punto, oppure fare clic sul primo punto per completare o chiudere la BSpline. La spline chiusa è anche una faccia, nonostante appaia come reticolo.

Options

  • Press F or the Finish button to finish the spline, leaving it open
  • Press C or the Close button or click on the first point to finish the spline, but making it closed by adding a last segment between the last point and the first one.
  • Press X, Y or Z after a point to constrain the next point on the given axis.
  • To enter coordinates manually, simply enter the numbers, then press ENTER between each X, Y and Z component.
  • Press R or click the checkbox to check/uncheck the Relative button. If relative mode is on, the coordinates of the next point are relative to the last one. If not, they are absolute, taken from the (0,0,0) origin point.
  • Press T or click the checkbox to check/uncheck the Continue button. If continue mode is on, the BSpline tool will restart after you finish or close it, allowing you to draw another one without pressing the BSpline button again.
  • Press CTRL while drawing to force snapping your point to the nearest snap location, independently of the distance.
  • Press SHIFT while drawing to constrain your next point horizontally or vertically in relation to the last one.
  • Press W or press the Wipe button to remove the existing segments and start the spline from the last point.
  • Press CTRL+Z or press the Undo button to undo the last point.
  • Press I or the Filled button to have the spline to appear as a face after it has been closed. This simply sets the View->Property of the Wire to "Flat lines" or "Wireframe", so it can easily be changed later.
  • Press ESC or the Cancel button to abort the current BSpline command.
  • BSplines, when in "Flat Lines" display mode, can display a hatch pattern, by setting their "Pattern" property below.

Properties

  • DatiClosed: Specifies if the spline is closed or not
  • VistaEnd Arrow: Shows an arrow symbol at the last point of the spline, so it can be used as an annotation leader line
  • VistaPattern: Specifies a hatch pattern to fill the wire with
  • VistaPattern Size: Specifies the size of the hatch pattern

Script

Lo strumento BSpline può essere utilizzato nelle macro e dalla console di Python tramite la seguente funzione:

 makeBSpline (pointslist,[closed],[placement])
  • La funzione crea un oggetto B-Spline dalla lista data di vettori.
  • Se closed è True, o se il primo e l'ultimo punto sono identici, il contorno è chiuso.
  • Se face è True (e quindi la BSpline è chiusa), la BSpline appare piena.
  • Al posto di un elenco di punti, si può anche fornire il contorno di una Parte.
  • Restituisce l'oggetto appena creato.

Esempio:

 import FreeCAD,Draft
 p1 = FreeCAD.Vector(0,0,0)
 p2 = FreeCAD.Vector(1,1,0)
 p3 = FreeCAD.Vector(2,0,0)
 Draft.makeBSpline([p1,p2,p3],closed=True)