PartDesign Draft/ro: Difference between revisions
(Created page with "=== Descriere === This tool creates angular draft on the selected faces of an object. A new separate Draft entry (followed by a sequential number if there are already existing...") |
No edit summary |
||
Line 14: | Line 14: | ||
[[Image:PartDesign_Draft-06.png|thumb|left|Checking the Reverse Direction box has applied an inward draft rather than outward.]] |
[[Image:PartDesign_Draft-06.png|thumb|left|Checking the Reverse Direction box has applied an inward draft rather than outward.]] |
||
| |
| |
||
=== |
=== Utilizare === |
||
* Select one or more faces on an object, then start the tool either by clicking its icon or going into the menu. |
* Select one or more faces on an object, then start the tool either by clicking its icon or going into the menu. |
||
* In Draft Parameters on the TaskPanel, set the required parameters and/or options as described below. |
* In Draft Parameters on the TaskPanel, set the required parameters and/or options as described below. |
||
* Click OK to validate. |
* Click OK to validate. |
||
* To edit the draft after the function has been validated, either double-click on the Draft label in the Project tree, or right-click on it and select '''Edit Draft'''. |
* To edit the draft after the function has been validated, either double-click on the Draft label in the Project tree, or right-click on it and select '''Edit Draft'''. |
||
=== |
=== Parametrii și Opțiuni === |
||
==== |
==== Adaugă o Fațetă / Șterge o Fațetă ==== |
||
Click Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. |
Click Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. |
||
==== Draft Angle ==== |
==== Draft Angle ==== |
||
Set the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. |
Set the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. |
||
==== |
==== Plan Neutru ==== |
||
Click Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. |
Click Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. |
||
==== Pull Direction ==== |
==== Pull Direction ==== |
||
Line 30: | Line 30: | ||
==== Reverse Pull Direction ==== |
==== Reverse Pull Direction ==== |
||
Checking Reverse Pull Direction will toggle the draft between positive and negative angles. |
Checking Reverse Pull Direction will toggle the draft between positive and negative angles. |
||
=== |
=== Cazuri speciale === |
||
The Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer. |
The Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer. |
||
|} |
|} |
Revision as of 10:25, 28 September 2018
PartDesign Draft |
Menu location |
---|
Part Design → Draft |
Workbenches |
Part Design |
Default shortcut |
None |
Introduced in version |
- |
See also |
None |
Descriere
This tool creates angular draft on the selected faces of an object. A new separate Draft entry (followed by a sequential number if there are already existing drafts in the document) is created in the Project tree.
Utilizare
Parametrii și OpțiuniAdaugă o Fațetă / Șterge o FațetăClick Add Face or Remove Face, then select a single face to update the list of active faces. Repeat as needed. Draft AngleSet the Draft Angle by entering a value or by clicking on the up/down arrows. The applied draft angle is shown in real time. Plan NeutruClick Neutral Plane, then select the plane that must not change dimensionally. The change is made in real time. Pull DirectionClick Pull Direction, then select an edge. Pull Direction is only effective if the Neutral Plane has been set. Results can be unpredictable. Reverse Pull DirectionChecking Reverse Pull Direction will toggle the draft between positive and negative angles. Cazuri specialeThe Draft tool will only function on faces that are normal to each other. If there are any tangential faces attached to the face you wish to apply draft to, it will fail. A common cause of failure is attempting to apply draft to a face that already has a fillet or chamfer applied to it. In this case, remove the tangential surface, apply the draft as need, then re-apply the fillet or chamfer. |