Poradnik: Sterownik kinematyczny
Ćwiczenie |
Temat |
---|
Sterownik kinematyczny utworzony w środowisku Python |
Poziom trudności |
Przydatna jest podstawowa znajomość języka Python |
Czas wykonania |
1 godzina |
Autorzy |
FBXL5 |
Wersja FreeCAD |
0.20 lub nowszy |
Pliki z przykładami |
Nie dołączono |
Zobacz również |
- |
Wprowadzenie
Ten poradnik opisuje jak z kilku linijek kodu Python wygenerować prosty kontroler kinematyczny do użycia z zespołami utworzonymi za pomocą środowiska pracy Złożenie 3.
Do kodowania można użyć dowolnego edytora tekstu. Mój wybór to Atom, ale wbudowany edytor FreeCAD też działa dobrze.
Poniższe przykłady kodu można skopiować i wkleić do pustego pliku tekstowego, a następnie zapisać pod wybraną nazwą jako plik typu *.py lub *.FCMacro.
Sekcje makrodefinicji
Podstawowa struktura
#! python
# -*- coding: utf-8 -*-
# (c) 2022 Your name LGPL
def main():
pass
if __name__ == "__main__":
# This will be true only if the file is "executed"
# but not if imported as a module
main()
Podstawowa struktura składa się z funkcji main()
oraz przełącznika sprawdzającego, czy makro jest używane jako kontener dla klas, metod itp. czy też jest uruchamiane samodzielnie. Tylko druga opcja powoduje uruchomienie funkcji main()
. Funkcja ta jest na razie pusta.
Wyznacz więzy prowadzące
Więzy prowadzące są obiektami w obrębie dokumentu FreeCAD. Należy je oznaczyć, aby można było je odnaleźć.
Dla tego kontrolera przyrostek "Driver"
musi być dołączony do etykiety wiązania prowadzącego. Może on być oddzielony znakiem "."
lub "-"
dla jasności, ponieważ będziemy sprawdzać tylko czy etykieta kończy się "Driver"
.
Funkcja, która otrzymuje obiekt dokumentu i zwraca listę więzów prowadzących (nazwy w tym przypadku) wykona zadanie.
def findTheDrivingConstraints(document_object):
# search through the Objects and find the driving constraint
driver_list = []
for each in document_object.Objects:
if each.Label.endswith("Driver"):
driving_constraint = each.Name
driver_list.append(driving_constraint)
return driver_list
Funkcja main()
ładuje aktywny dokument do zmiennej kin_doc
, a następnie wywołuje funkcję findTheDrivingConstraints()
i przekazuje jej zawartość kin_doc
. Zwrócona lista jest ładowana do drivers
, która następnie jest sprawdzana, czy zawiera przynajmniej jeden element. Jeśli tak jest, lista jest ostatecznie wyświetlona w widoku Raportu.
def main():
kin_doc = App.ActiveDocument # Kinematic Document
drivers = findTheDrivingConstraints(kin_doc)
if len(drivers) < 1:
print("No driver found!")
else:
print(drivers)
Dotychczasowe makrodefinicje ...
#! python
# -*- coding: utf-8 -*-
# (c) 2021 Your name LGPL
def findTheDrivingConstraints(document_object):
# search through the Objects and find the driving constraint
driver_list = []
for each in document_object.Objects:
if each.Label.endswith("Driver"):
driving_constraint = each.Name
driver_list.append(driving_constraint)
return driver_list
def main():
kin_doc = App.ActiveDocument # Kinematic Document
drivers = findTheDrivingConstraints(kin_doc)
if len(drivers) < 1:
print("No driver found!")
else:
print(drivers)
if __name__ == "__main__":
# This will be true only if the file is "executed"
# but not if imported as a module
main()
Panel sterowania
Panel sterowania jest zbudowany z widżetów Qt, jedno główne okno zawierające kilka widżetów wejścia / wyjścia.
Każdy widżet musi zostać zaimportowany, zanim będzie można go użyć, ale można je zaimportować jako pojedynczy zestaw. Linia importu jest umieszczona w pobliżu górnej części pliku.
Okno główne
W głównym oknie linia importu wygląda tak:
from PySide2.QtWidgets import (QDialog)
Okno główne o nazwie ControlPanel
to obiekt klasy utworzony z widżetu QDialog
.
Posiada ona dwie metody init. Metoda __init__()
inicjalizuje nowy obiekt klasy, obsługuje przychodzące argumenty oraz uruchamia metodę initUI()
, która zarządza wszystkimi widżetami w obrębie okna głównego.
class ControlPanel(QDialog):
"""
docstring for ControlPanel.
"""
def __init__(self, document, actuator):
super(ControlPanel, self).__init__()
self.initUI(document, actuator)
def initUI(self, document, actuator):
# Setting up class parameters
# the window has 640 x 480 pixels and is centered by default
# now make the window visible
self.show()
Aby uruchomić pojedynczy panel sterowania, zostanie utworzona instancja tej klasy o nazwie panel
, z kin_doc
(obiekt dokumentu) oraz drivers[0]
(pierwsze z listy wiązań dotyczących prowadzenia) przekazanymi do tej instancji. Na koniec metoda exec_()
klasy otwiera okno dialogowe.
panel = ControlPanel(kin_doc, drivers[0])
panel.exec_()
Aby obsłużyć więcej niż jeden sterownik, musimy sprawdzić listę sterowników i utworzyć instancję dla każdej pozycji na liście i przenieść bieżącą pozycję.
panel_list = []
for each_driver in drivers:
panel = ControlPanel(kin_doc, each_driver)
panel_list.append(panel)
panel.exec_()
Te linie zastępują polecenie print()
w gałęzi else funkcji main()
.
Uwaga: Zebranie panel_list
pozwala na uruchomienie wszystkich paneli jednocześnie. (Nie potrafię jeszcze wyjaśnić tego zachowania...)
Uruchomienie makra spowoduje wyświetlenie nowego, pustego okna dialogowego czekającego na widżety:
Dotychczasowe makrodefinicje ...
#! python
# -*- coding: utf-8 -*-
# (c) 2021 Your name LGPL
# imports and constants
from PySide2.QtWidgets import (QDialog)
class ControlPanel(QDialog):
"""
docstring for ControlPanel.
"""
def __init__(self, document, actuator):
super(ControlPanel, self).__init__()
self.initUI(document, actuator)
def initUI(self, document, actuator):
# Setting up class parameters
# the window has 640 x 480 pixels and is centered by default
# now make the window visible
self.show()
def findTheDrivingConstraints(document_object):
# search through the Objects and find the driving constraint
driver_list = []
for each in document_object.Objects:
if each.Label.endswith("Driver"):
driving_constraint = each.Name
driver_list.append(driving_constraint)
return driver_list
def main():
kin_doc = App.ActiveDocument # Kinematic Document
drivers = findTheDrivingConstraints(kin_doc)
if len(drivers) < 1:
print("No driver found!")
else:
panel_list = []
for each_driver in drivers:
panel = ControlPanel(kin_doc, each_driver)
panel_list.append(panel)
panel.exec_()
if __name__ == "__main__":
# This will be true only if the file is "executed"
# but not if imported as a module
main()
Ustawienie parametrów
Teraz przyszedł czas na wypełnienie metody initUI()
:
...
def initUI(self, document, actuator):
# Setting up class parameters
self.actuator = document.getObject(actuator)
self.driver_type = self.getDriverType(self.actuator)
# the window has 640 x 480 pixels and is centered by default
# now make the window visible
self.show()
...
self.actuator
reprezentuje wiązanie napędowe, a self.driver_type
przechowuje słowo kluczowe dla jego typu. To ostatnie jest używane do wyboru odpowiedniej właściwości z każdym wiązaniem.
Metoda getDriverType()
Do późniejszego użycia potrzebujemy typ sterownika (Kąt, Odległość, Długość) i dlatego należy zdefiniować metodę getDriverType()
:
...
def getDriverType(self, constraint):
ANGLE_CONSTRAINTS = [
"Angle",
"PlaneCoincident",
"AxialAlignment",
"PlaneAlignment"
]
DISTANCE_CONSTRAINTS = [
"PointDistance",
"PointsDistance"
]
if constraint.ConstraintType in ANGLE_CONSTRAINTS:
return "Angle"
elif constraint.ConstraintType in DISTANCE_CONSTRAINTS:
return "Distance"
else:
return "Length"
...
Metoda ta sprawdza, czy typ podanego wiązania można znaleźć na jednej z list i zwraca, który rodzaj wymiaru ma być kontrolowany.
Zakłada się, że w dokumencie kinematycznym sterownik jest zaznaczony poprawnie i działa, jeśli jest edytowany ręcznie. W tym przypadku nie ma potrzeby filtrowania wiązań geometrycznych takich jak Współliniowość czy Zbieżność punktu (ale tutaj byłoby to uzasadnione ...).
Ustawienia okna
Rozmiar okna jest określony przez jego minimalny i maksymalny wymiar. Użycie tych samych wartości powoduje, że rozmiar jest stały.
Tytuł pokazuje nazwę sterownika i czy jest to kąt, odległość czy długość. Wreszcie okno ma pozostać na wierzchu wszystkich okien.
...
# the window has 640 x 480 pixels and is centered by default
#- set window dimensions
self.setMaximumWidth(400)
self.setMaximumHeight(200)
self.setMinimumWidth(400)
self.setMinimumHeight(200)
self.setWindowTitle(self.actuator.Label + ": " + self.driver_type)
self.setWindowFlags(QtCore.Qt.WindowStaysOnTopHint)
# now make the window visible
...
Ustawienie dodatkowych parametrów
Kolejnym krokiem jest wyodrębnienie aktualnej wartości sterownika i ustawienie domyślnych wartości początkowych i końcowych w zależności od typu sterownika.
Odległość nie może być ujemna i dokładnie zero stanowi zagadkę dla rozwiązania, dlatego wartość początkowa jest ustawiona na 0,001. Kąty przyjmują wartości ujemne i otrzymują wartości symetryczne. (Czy długości przyjmują wartości ujemne trzeba ostatecznie udowodnić ...)
Przyrostek jednostki musi zostać zachowany, aby na końcu zwrócić wartość do właściwości wiązanie. Odległości i długości wymagają wartości z jednostkami.
Radzenie sobie z jednostkami i wyświetlanie wartości jako ciągów w kilku widżetach wymaga dość często konwersji liczb na ciągi i odwrotnie.
Aby uzupełnić parametry ustawiamy domyślną liczbę kroków, które powinny być obliczane podczas automatyzacji ruchu, a jeśli przełącznik self.sequence
jest ustawiony na wartość True
, to przy każdym kroku ruchu będzie robione zdjęcie.
...
self.steps_value = 10
self.sequence = False
if self.driver_type == "Angle":
self.current_value = self.actuator.Angle
self.start_value = (self.current_value - 15)
self.end_value = (self.current_value + 15)
self.unit_suffix = (" °")
elif self.driver_type == "Distance":
self.current_value = float(str(self.actuator.Distance)[:-3])
self.start_value = 0.001 # Distance must not be <= 0
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
else:
self.current_value = float(str(self.actuator.Offset)[:-3])
self.start_value = (self.current_value - 10)
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
...
Etykiety
Teraz dodano trzy etykiety, które wyświetlają wartość początkową, końcową i bieżącą.
Najpierw należy zaimportować klasę QLabel
, tzn. rozszerzyć listę importu w sposób następujący:
from PySide2.QtWidgets import (QDialog, QLabel)
Wracając do metody initUI()
wstawiamy:
...
# create some labels
self.label_start = QLabel("", self)
self.label_start.setFont("osifont") # set to a non-proportional font
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
self.label_start.setGeometry(QtCore.QRect(30, 15, 60, 25))
self.label_end = QLabel("", self)
self.label_end.setFont("osifont")
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
self.label_end.setGeometry(QtCore.QRect(320, 15, 60, 25))
self.label_current = QLabel("", self)
self.label_current.setFont("osifont")
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
self.label_current.setGeometry(QtCore.QRect(130, 15, 150, 25))
...
Umieszczenie odbywa się za pomocą dziedziczonej metody setGeometry()
. W tym przypadku wykorzystywany jest opis prostokąta (pozycja X, pozycja Y, szerokość, wysokość).
Pierwszy i trzeci wiersz można by połączyć, ale nie jest to zalecane ze względu na przejrzystość:
self.label_end = QLabel((str(round(self.end_value, 1)) + self.unit_suffix), self)
Uruchomienie makra z dokumentem zespołu kinematycznego spowoduje powstanie okna dialogowego jak poniżej:
Okno dialogowe wyświetlające etykietę wiązania i typ sterownika w tytule oraz wartość początkową, wartość bieżącą i wartość końcową w pierwszej linii w obszarze głównym
Dotychczasowe makrodefinicje ...
#! python
# -*- coding: utf-8 -*-
# (c) 2021 Your name LGPL
# imports and constants
from PySide2.QtWidgets import (QDialog, QLabel)
class ControlPanel(QDialog):
"""
docstring for ControlPanel.
"""
def __init__(self, document, actuator):
super(ControlPanel, self).__init__()
self.initUI(document, actuator)
def initUI(self, document, actuator):
# Setting up class parameters
self.actuator = document.getObject(actuator)
self.driver_type = self.getDriverType(self.actuator)
self.steps_value = 10
self.sequence = False
if self.driver_type == "Angle":
self.current_value = self.actuator.Angle
self.start_value = (self.current_value - 15)
self.end_value = (self.current_value + 15)
self.unit_suffix = (" °")
elif self.driver_type == "Distance":
self.current_value = float(str(self.actuator.Distance)[:-3])
self.start_value = 0.001 # Distance must not be <= 0
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
else:
self.current_value = float(str(self.actuator.Offset)[:-3])
self.start_value = (self.current_value - 10)
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
# the window has 640 x 480 pixels and is centered by default
#- set window dimensions
self.setMaximumWidth(400)
self.setMaximumHeight(200)
self.setMinimumWidth(400)
self.setMinimumHeight(200)
self.setWindowTitle(self.actuator.Label + ": " + self.driver_type)
self.setWindowFlags(QtCore.Qt.WindowStaysOnTopHint)
# create some labels
self.label_start = QLabel("", self)
self.label_start.setFont("osifont") # set to a non-proportional font
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
self.label_start.setGeometry(QtCore.QRect(30, 15, 60, 25))
self.label_end = QLabel("", self)
self.label_end.setFont("osifont")
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
self.label_end.setGeometry(QtCore.QRect(320, 15, 60, 25))
self.label_current = QLabel("", self)
self.label_current.setFont("osifont")
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
self.label_current.setGeometry(QtCore.QRect(130, 15, 150, 25))
# now make the window visible
self.show()
def getDriverType(self, constraint):
ANGLE_CONSTRAINTS = [
"Angle",
"PlaneCoincident",
"AxialAlignment",
"PlaneAlignment"
]
DISTANCE_CONSTRAINTS = [
"PointDistance",
"PointsDistance"
]
if constraint.ConstraintType in ANGLE_CONSTRAINTS:
return "Angle"
elif constraint.ConstraintType in DISTANCE_CONSTRAINTS:
return "Distance"
else:
return "Length"
# End of ControlPanel()
# Main section below:
def findTheDrivingConstraints(document_object):
# search through the Objects and find the driving constraint
driver_list = []
for each in document_object.Objects:
if each.Label.endswith("Driver"):
driving_constraint = each.Name
driver_list.append(driving_constraint)
return driver_list
def main():
kin_doc = App.ActiveDocument # Kinematic Document
drivers = findTheDrivingConstraints(kin_doc)
if len(drivers) < 1:
print("No driver found!")
else:
panel_list = []
for each_driver in drivers:
panel = ControlPanel(kin_doc, each_driver)
panel_list.append(panel)
panel.exec_()
if __name__ == "__main__":
# This will be true only if the file is "executed"
# but not if imported as a module
main()
Slider
Aby zmienić bieżącą wartość na dowolną liczbę między wartością początkową a końcową, przydatny byłby widżet suwaka.
Najpierw należy zaimportować klasę QSlider
, tzn. rozszerzyć listę importu w sposób następujący:
from PySide2.QtWidgets import (QDialog, QLabel, QSlider)
Wracając do metody initUI()
i zaraz po sekcji labels wstawiamy:
...
# Horizontal slider
self.actuator_slider = QSlider(self) # create horizontalSlider
self.actuator_slider.setOrientation(QtCore.Qt.Horizontal) # orientation horizontal
self.actuator_slider.setGeometry(QtCore.QRect(30, 50, 330, 25)) # position coordinates
self.actuator_slider.setObjectName("horizontalSlider") # object name
self.actuator_slider.setInvertedAppearance(False) # default: right to left
self.actuator_slider.setRange(0, 100) # default: (0, 99)
self.actuator_slider.setValue(self.current_value / self.stepRatio())
self.actuator_slider.valueChanged.connect(self.onActuatorSlider)
...
The slider button is placed with the setValue()
method. Its value has to be calculated from the current value and a step ratio. The ratio has to be calculated whenever a start or end value is changed and so we insert another method after the getDriverType()
method.
To work with a ratio instead of altering the slider's min and max values has the advantage of a finer resolution for small values.
...
def stepRatio(self):
ratio = (self.end_value - self.start_value) / 100
return ratio
...
And after this one comes another method defining what to do when the slider position or the slider value changes. The onActuatorSlider()
method is called by the connect()
method which also hands over the slider value as an argument.
It recalculates the current value from the slider position, rewrites the text of the label self.label_current
and changes the constraint property according to the driver type.
Running the command "asm3CmdQuickSolve"
starts the solver to rearrange the assembly parts with the altered value.
...
def onActuatorSlider(self, slider_value):
self.current_value = slider_value * self.stepRatio() + self.start_value
if self.driver_type == "Angle":
self.actuator.Angle = self.current_value
elif self.driver_type == "Distance":
self.actuator.Distance = self.current_value
else:
self.actuator.Offset = self.current_value
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
Gui.runCommand("asm3CmdQuickSolve", 0)
...
The dialog window with the slider should look like this and is ready to control a motion:
Dialog windows with the added slider, one for an Angle driver and one for a Distance driver
We can start a dialog window for any opened document, they won't interfere with each other.
Text entry fields
To set the start and end value we use a line edit widget.
First the class QLineEdit
must be imported i.e. the import list has to be extended like this:
from PySide2.QtWidgets import (QDialog, QLabel, QSlider, QLineEdit)
Back in the initUI()
method and between the labels and the slider sections we insert:
...
# text input field - Start value
self.entry_start = QLineEdit(self)
self.entry_start.setText(str(round(self.start_value, 1)))
self.entry_start.setGeometry(QtCore.QRect(30, 80, 50, 25))
self.entry_start.textChanged[str].connect(self.onEntryStart)
# text input field - End value
self.entry_end = QLineEdit(self)
self.entry_end.setText(str(round(self.end_value, 1)))
self.entry_end.setGeometry(QtCore.QRect(320, 80, 50, 25))
self.entry_end.textChanged[str].connect(self.onEntryEnd)
...
The entry fields display the default start and end values. They are not complete until we add the methods to deal with altered entries. This will be done by the methods self.onEntryStart()
and self.onEntryEnd()
that are inserted between the self.stepRatio()
and the self.onActuatorSlider()
methods.
...
def onEntryStart(self, new_start):
self.start_value = float(new_start)
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
def onEntryEnd(self, new_end):
self.end_value = float(new_end)
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
...
Both convert the received string value to a floating point number and change either self.start_value
or self.end_value
and the corresponding label accordingly. After that the slider value is updated.
The dialog window with text entry fields should look like this and is ready to change the range of a motion:
Dialog windows with line edit fields, again for an angle and a distance driver
Dotychczasowe makrodefinicje ...
#! python
# -*- coding: utf-8 -*-
# (c) 2021 Your name LGPL
# imports and constants
from PySide2.QtWidgets import (QDialog, QLabel, QSlider, QLineEdit)
class ControlPanel(QDialog):
"""
docstring for ControlPanel.
"""
def __init__(self, document, actuator):
super(ControlPanel, self).__init__()
self.initUI(document, actuator)
def initUI(self, document, actuator):
# Setting up class parameters
self.actuator = document.getObject(actuator)
self.driver_type = self.getDriverType(self.actuator)
self.steps_value = 10
self.sequence = False
if self.driver_type == "Angle":
self.current_value = self.actuator.Angle
self.start_value = (self.current_value - 15)
self.end_value = (self.current_value + 15)
self.unit_suffix = (" °")
elif self.driver_type == "Distance":
self.current_value = float(str(self.actuator.Distance)[:-3])
self.start_value = 0.001 # Distance must not be <= 0
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
else:
self.current_value = float(str(self.actuator.Offset)[:-3])
self.start_value = (self.current_value - 10)
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
# the window has 640 x 480 pixels and is centered by default
#- set window dimensions
self.setMaximumWidth(400)
self.setMaximumHeight(200)
self.setMinimumWidth(400)
self.setMinimumHeight(200)
self.setWindowTitle(self.actuator.Label + ": " + self.driver_type)
self.setWindowFlags(QtCore.Qt.WindowStaysOnTopHint)
# create some labels
self.label_start = QLabel("", self)
self.label_start.setFont("osifont") # set to a non-proportional font
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
self.label_start.setGeometry(QtCore.QRect(30, 15, 60, 25))
self.label_end = QLabel("", self)
self.label_end.setFont("osifont")
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
self.label_end.setGeometry(QtCore.QRect(320, 15, 60, 25))
self.label_current = QLabel("", self)
self.label_current.setFont("osifont")
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
self.label_current.setGeometry(QtCore.QRect(130, 15, 150, 25))
# create some input elements
# text input field - Start value
self.entry_start = QLineEdit(self)
self.entry_start.setText(str(round(self.start_value, 1)))
self.entry_start.setGeometry(QtCore.QRect(30, 80, 50, 25))
self.entry_start.textChanged[str].connect(self.onEntryStart)
# text input field - End value
self.entry_end = QLineEdit(self)
self.entry_end.setText(str(round(self.end_value, 1)))
self.entry_end.setGeometry(QtCore.QRect(320, 80, 50, 25))
self.entry_end.textChanged[str].connect(self.onEntryEnd)
# Horizontal slider
self.actuator_slider = QSlider(self) # create horizontalSlider
self.actuator_slider.setOrientation(QtCore.Qt.Horizontal) # orientation horizontal
self.actuator_slider.setGeometry(QtCore.QRect(30, 50, 330, 25)) # position coordinates
self.actuator_slider.setObjectName("horizontalSlider") # object name
self.actuator_slider.setInvertedAppearance(False) # default: right to left
self.actuator_slider.setRange(0, 100) # default: (0, 99)
self.actuator_slider.setValue(self.current_value / self.stepRatio())
self.actuator_slider.valueChanged.connect(self.onActuatorSlider)
# now make the window visible
self.show()
def getDriverType(self, constraint):
ANGLE_CONSTRAINTS = [
"Angle",
"PlaneCoincident",
"AxialAlignment",
"PlaneAlignment"
]
DISTANCE_CONSTRAINTS = [
"PointDistance",
"PointsDistance"
]
if constraint.ConstraintType in ANGLE_CONSTRAINTS:
return "Angle"
elif constraint.ConstraintType in DISTANCE_CONSTRAINTS:
return "Distance"
else:
return "Length"
def stepRatio(self):
ratio = (self.end_value - self.start_value) / 100
return ratio
def onEntryStart(self, new_start):
self.start_value = float(new_start)
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
def onEntryEnd(self, new_end):
self.end_value = float(new_end)
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
def onActuatorSlider(self, slider_value):
self.current_value = slider_value * self.stepRatio() + self.start_value
if self.driver_type == "Angle":
self.actuator.Angle = self.current_value
elif self.driver_type == "Distance":
self.actuator.Distance = self.current_value
else:
self.actuator.Offset = self.current_value
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
Gui.runCommand("asm3CmdQuickSolve", 0)
print(slider_value, self.current_value)
# End of ControlPanel()
# Main section below:
def findTheDrivingConstraints(document_object):
# search through the Objects and find the driving constraint
driver_list = []
for each in document_object.Objects:
if each.Label.endswith("Driver"):
driving_constraint = each.Name
driver_list.append(driving_constraint)
return driver_list
def main():
kin_doc = App.ActiveDocument # Kinematic Document
drivers = findTheDrivingConstraints(kin_doc)
if len(drivers) < 1:
print("No driver found!")
else:
panel_list = []
for each_driver in drivers:
panel = ControlPanel(kin_doc, each_driver)
panel_list.append(panel)
panel.exec_()
if __name__ == "__main__":
# This will be true only if the file is "executed"
# but not if imported as a module
main()
Motion
To get the assembly in motion we need:
- Buttons to trigger motion in the desired direction.
- An input field to alter the number of steps for faster or smoother motions.
- A check box to indicate if we want to shoot a sequence of images.
Forward and Backward buttons
To move the assembly parts automatically we need two buttons to trigger the motions, one towards the start position and one towards the end position. These two and a close button will use a QPushButton
widget.
Small assemblies compute a bit too fast and show jumps instead of a smooth motion. To slow it down we use the sleep()
method of the time
module which has to be imported first.
Another import and another widget:
import time
from PySide2.QtWidgets import (QDialog, QLabel, QSlider, QLineEdit, QPushButton)
Back in the initUI()
method we insert the buttons after the slider section:
...
# forward button
self.forward_button = QPushButton(">->", self)
self.forward_button.setGeometry(QtCore.QRect(240, 80, 50, 25))
self.forward_button.setAutoDefault(False)
self.forward_button.clicked.connect(self.onForward)
# backward button
self.backward_button = QPushButton("<-<", self)
self.backward_button.setGeometry(QtCore.QRect(100, 80, 50, 25))
self.backward_button.setAutoDefault(False)
self.backward_button.clicked.connect(self.onBackward)
# close button
self.close_button = QPushButton("Close window", self)
self.close_button.setGeometry(QtCore.QRect(120, 160, 130, 25))
self.close_button.setAutoDefault(False)
self.close_button.clicked.connect(self.onClose)
...
The methods dealing with pressed buttons are self.onForward()
, self.onBackward()
, and self.onClose()
. They are inserted after the onActuatorSlider()
method.
...
def onForward(self):
steps_left = self.steps_value
print(self.steps_value)
step = ((self.end_value - self.current_value) / steps_left)
while steps_left > 0:
self.current_value += step
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
time.sleep(0.2)
steps_left -= 1
self.actuator_slider.setValue(100)
def onBackward(self):
steps_left = self.steps_value
step = ((self.current_value - self.start_value) / steps_left)
while steps_left > 0:
self.current_value -= step
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
time.sleep(0.2)
steps_left -= 1
self.actuator_slider.setValue(0)
def onClose(self):
self.result = "Closed"
self.close()
...
The method self.onClose()
invokes the inherited method self.close()
which just closes the dialog window and thereby ends the macro.
Both self.onForward()
and self.onBackward()
count the steps that are left to go to reach the wanted position and calculate the length of a step according to the number of steps. For now we go with the default number of 10 steps.
Each round on the while loop increases/decreases the current value and updates the slider values which triggers onActuatorSlider()
in the background (see Slider paragraph). After a pause to let the computer provide another updated 3D view, counting down the steps left to go finishes the loop.
With no steps left the slider is set to the first/last slider position, just in case if a rounding error had occurred.
The dialog window with buttons should look like this and can now move the assembly by 10 steps towards the wanted start/end position:
Dialog window with buttons
And the macro so far...
#! python
# -*- coding: utf-8 -*-
# (c) 2021 Your name LGPL
# imports and constants
import time
from PySide2.QtWidgets import (QDialog, QLabel, QSlider, QLineEdit, QPushButton)
class ControlPanel(QDialog):
"""
docstring for ControlPanel.
"""
def __init__(self, document, actuator):
super(ControlPanel, self).__init__()
self.initUI(document, actuator)
def initUI(self, document, actuator):
# Setting up class parameters
self.actuator = document.getObject(actuator)
self.driver_type = self.getDriverType(self.actuator)
self.steps_value = 10
self.sequence = False
if self.driver_type == "Angle":
self.current_value = self.actuator.Angle
self.start_value = (self.current_value - 15)
self.end_value = (self.current_value + 15)
self.unit_suffix = (" °")
elif self.driver_type == "Distance":
self.current_value = float(str(self.actuator.Distance)[:-3])
self.start_value = 0.001 # Distance must not be <= 0
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
else:
self.current_value = float(str(self.actuator.Offset)[:-3])
self.start_value = (self.current_value - 10)
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
# the window has 640 x 480 pixels and is centered by default
#- set window dimensions
self.setMaximumWidth(400)
self.setMaximumHeight(200)
self.setMinimumWidth(400)
self.setMinimumHeight(200)
self.setWindowTitle(self.actuator.Label + ": " + self.driver_type)
self.setWindowFlags(QtCore.Qt.WindowStaysOnTopHint)
# create some labels
self.label_start = QLabel("", self)
self.label_start.setFont("osifont") # set to a non-proportional font
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
self.label_start.setGeometry(QtCore.QRect(30, 15, 60, 25))
self.label_end = QLabel("", self)
self.label_end.setFont("osifont")
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
self.label_end.setGeometry(QtCore.QRect(320, 15, 60, 25))
self.label_current = QLabel("", self)
self.label_current.setFont("osifont")
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
self.label_current.setGeometry(QtCore.QRect(130, 15, 150, 25))
# create some input elements
# text input field - Start value
self.entry_start = QLineEdit(self)
self.entry_start.setText(str(round(self.start_value, 1)))
self.entry_start.setGeometry(QtCore.QRect(30, 80, 50, 25))
self.entry_start.textChanged[str].connect(self.onEntryStart)
# text input field - End value
self.entry_end = QLineEdit(self)
self.entry_end.setText(str(round(self.end_value, 1)))
self.entry_end.setGeometry(QtCore.QRect(320, 80, 50, 25))
self.entry_end.textChanged[str].connect(self.onEntryEnd)
# Horizontal slider
self.actuator_slider = QSlider(self) # create horizontalSlider
self.actuator_slider.setOrientation(QtCore.Qt.Horizontal) # orientation horizontal
self.actuator_slider.setGeometry(QtCore.QRect(30, 50, 330, 25)) # position coordinates
self.actuator_slider.setObjectName("horizontalSlider") # object name
self.actuator_slider.setInvertedAppearance(False) # default: right to left
self.actuator_slider.setRange(0, 100) # default: (0, 99)
self.actuator_slider.setValue(self.current_value / self.stepRatio())
self.actuator_slider.valueChanged.connect(self.onActuatorSlider)
# forward button
self.forward_button = QPushButton(">->", self)
self.forward_button.setGeometry(QtCore.QRect(240, 80, 50, 25))
self.forward_button.setAutoDefault(False)
self.forward_button.clicked.connect(self.onForward)
# backward button
self.backward_button = QPushButton("<-<", self)
self.backward_button.setGeometry(QtCore.QRect(100, 80, 50, 25))
self.backward_button.setAutoDefault(False)
self.backward_button.clicked.connect(self.onBackward)
# close button
self.close_button = QPushButton("Close window", self)
self.close_button.setGeometry(QtCore.QRect(120, 160, 130, 25))
self.close_button.setAutoDefault(False)
self.close_button.clicked.connect(self.onClose)
# now make the window visible
self.show()
def getDriverType(self, constraint):
ANGLE_CONSTRAINTS = [
"Angle",
"PlaneCoincident",
"AxialAlignment",
"PlaneAlignment"
]
DISTANCE_CONSTRAINTS = [
"PointDistance",
"PointsDistance"
]
if constraint.ConstraintType in ANGLE_CONSTRAINTS:
return "Angle"
elif constraint.ConstraintType in DISTANCE_CONSTRAINTS:
return "Distance"
else:
return "Length"
def stepRatio(self):
ratio = (self.end_value - self.start_value) / 100
return ratio
def onEntryStart(self, new_start):
self.start_value = float(new_start)
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
def onEntryEnd(self, new_end):
self.end_value = float(new_end)
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
def onActuatorSlider(self, slider_value):
self.current_value = slider_value * self.stepRatio() + self.start_value
if self.driver_type == "Angle":
self.actuator.Angle = self.current_value
elif self.driver_type == "Distance":
self.actuator.Distance = self.current_value
else:
self.actuator.Offset = self.current_value
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
FreeCADGui.updateGui() # screen update between steps
Gui.runCommand("asm3CmdQuickSolve", 0)
def onForward(self):
steps_left = self.steps_value
print(self.steps_value)
step = ((self.end_value - self.current_value) / steps_left)
while steps_left > 0:
self.current_value += step
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
time.sleep(0.2)
steps_left -= 1
self.actuator_slider.setValue(100)
def onBackward(self):
steps_left = self.steps_value
step = ((self.current_value - self.start_value) / steps_left)
while steps_left > 0:
self.current_value -= step
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
time.sleep(0.2)
steps_left -= 1
self.actuator_slider.setValue(0)
def onClose(self):
self.result = "Closed"
self.close()
# End of ControlPanel()
# Main section below:
def findTheDrivingConstraints(document_object):
# search through the Objects and find the driving constraint
driver_list = []
for each in document_object.Objects:
if each.Label.endswith("Driver"):
driving_constraint = each.Name
driver_list.append(driving_constraint)
return driver_list
def main():
kin_doc = App.ActiveDocument # Kinematic Document
drivers = findTheDrivingConstraints(kin_doc)
if len(drivers) < 1:
print("No driver found!")
else:
panel_list = []
for each_driver in drivers:
panel = ControlPanel(kin_doc, each_driver)
panel_list.append(panel)
panel.exec_()
if __name__ == "__main__":
# This will be true only if the file is "executed"
# but not if imported as a module
main()
Number of steps
The default setting is to get a quick impression if the assembly is moving as expected without wasting too much computing time.
If the parts jump rather than move smoothly, or if drivers based on angles tend to cause trouble when the difference between two angles is too large, then both can be fixed by increasing the number of steps.
And so another line edit widget is used to alter the number steps (placed after the existing line edit widgets):
...
# text input field - number of steps
self.entry_steps = QLineEdit(self)
self.entry_steps.setText(str(int(self.steps_value)))
self.entry_steps.setGeometry(QtCore.QRect(180, 80, 50, 25))
self.entry_steps.textChanged[str].connect(self.onEntrySteps)
...
The related method self.onEntrySteps()
just fills the parameter self.step_value
with the entered value. It is inserted after the onEntryEnd()
method.
...
def onEntrySteps(self, new_steps):
self.steps_value = int(new_steps)
...
The dialog window able to change the number of steps should look like this:
Dialog window with another text entry field
Sekwencja obrazów
Gdy ruch wykonywany przez złożenie spełnia nasze oczekiwania, możemy zrobić zdjęcie każdego kroku. Powstała sekwencja zdjęć może posłużyć do stworzenia krótkiej animacji gif.
Do realizacji tej funkcjonalności potrzebujemy widżetu QCheckBox
, oraz katalogu do przechowywania obrazków.
Jeszcze jeden import i widżet:
import time
from PySide2.QtWidgets import (QDialog, QLabel, QSlider, QLineEdit, QPushButton, QCheckBox)
Wracając do metody initUI()
wstawiamy pole wyboru po sekcji suwaka:
...
# output check box
self.output_check = QCheckBox(self)
self.output_check.setGeometry(QtCore.QRect(40, 120, 300, 25))
self.output_check.setChecked(False)
self.output_check.setText("Check to record an image sequence")
self.output_check.setObjectName("checkBoxOutput")
self.output_check.clicked.connect(self.onOutputClicked)
...
Metoda onOutputClicked()
synchronizuje parametr self.sequence
i wyświetlenie znaku kontrolnego.
...
def onOutputClicked(self):
if self.sequence == True:
self.sequence = False
self.output_check.setChecked(False)
else:
self.sequence = True
self.output_check.setChecked(True)
...
Do określenia parametrów wyjściowych używamy metody output()
:
...
def output(self, counter):
if (self.sequence == True):
image_path = ".../FreeCAD/ScreenShots/Sequence"
file_tag = ".png"
height = 640
width = 480
background = "Transparent"
# dealing with leading zeros
if (counter > 999) or (counter < 0):
print("Out of Range")
elif (counter < 10):
number = "00" + str(counter)
elif (counter < 100):
number = "0" + str(counter)
else:
number = str(counter)
# Screen shot
Gui.activeDocument().activeView().saveImage(image_path + number + file_tag, height, width, background)
...
Przede wszystkim ścieżka do obrazów musi być dostosowana do Twojego systemu operacyjnego. Ostatnią częścią jest określenie nazwy obrazu bez numeru bieżącego i tagu pliku. Na razie trzeba to zrobić samodzielnie.
Następnie podążaj za tagiem pliku, aby zakończyć nazwę obrazu, nadać wysokość i szerokość obrazu oraz sposób wypełnienia tła ("Bieżące"
(tło widoku 3D), "Białe"
, "Czarne"
lub "Przezroczyste"
).
Aby zawsze mieć trzycyfrową liczbę, należy przed parametrem licznika umieścić wiodące zera.
W końcu oskryptowana wersja polecenia Zrzut ekranu jest używana do robienia zdjęcia na podstawie wspomnianych parametrów.
Nadal nie zrobiono zdjęć!!! Nie ma problemu, ponieważ ta metoda nie została jeszcze wywołana, a więc musimy wstawić wywołanie w pętli while onForward()
i onBackward()
. Zaraz po time.sleep(0,2)
wstawiamy tę linię:
...
self.output(steps_left)
...
Teraz makrodefinicja powinno być gotowa do sterowania złożeniem oraz do robienia zdjęć do animowanego gifa.
Końcowa wersja okna dialogowego:
Ukończone okno dialogowe.
I wreszcie całe makro
Nie zapomnij ustawić ścieżki w metodzie output()!
#! python
# -*- coding: utf-8 -*-
# (c) 2021 Your name LGPL
# imports and constants
import time
from PySide2.QtWidgets import (QDialog, QLabel, QSlider, QLineEdit, QPushButton, QCheckBox)
class ControlPanel(QDialog):
"""
docstring for ControlPanel.
"""
def __init__(self, document, actuator):
super(ControlPanel, self).__init__()
self.initUI(document, actuator)
def initUI(self, document, actuator):
# Setting up class parameters
self.actuator = document.getObject(actuator)
self.driver_type = self.getDriverType(self.actuator)
self.steps_value = 10
self.sequence = False
if self.driver_type == "Angle":
self.current_value = self.actuator.Angle
self.start_value = (self.current_value - 15)
self.end_value = (self.current_value + 15)
self.unit_suffix = (" °")
elif self.driver_type == "Distance":
self.current_value = float(str(self.actuator.Distance)[:-3])
self.start_value = 0.001 # Distance must not be <= 0
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
else:
self.current_value = float(str(self.actuator.Offset)[:-3])
self.start_value = (self.current_value - 10)
self.end_value = (self.current_value + 10)
self.unit_suffix = (" mm")
# the window has 640 x 480 pixels and is centered by default
#- set window dimensions
self.setMaximumWidth(400)
self.setMaximumHeight(200)
self.setMinimumWidth(400)
self.setMinimumHeight(200)
self.setWindowTitle(self.actuator.Label + ": " + self.driver_type)
self.setWindowFlags(QtCore.Qt.WindowStaysOnTopHint)
# create some labels
self.label_start = QLabel("", self)
self.label_start.setFont("osifont") # set to a non-proportional font
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
self.label_start.setGeometry(QtCore.QRect(30, 15, 60, 25))
self.label_end = QLabel("", self)
self.label_end.setFont("osifont")
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
self.label_end.setGeometry(QtCore.QRect(320, 15, 60, 25))
self.label_current = QLabel("", self)
self.label_current.setFont("osifont")
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
self.label_current.setGeometry(QtCore.QRect(130, 15, 150, 25))
# create some input elements
# text input field - Start value
self.entry_start = QLineEdit(self)
self.entry_start.setText(str(round(self.start_value, 1)))
self.entry_start.setGeometry(QtCore.QRect(30, 80, 50, 25))
self.entry_start.textChanged[str].connect(self.onEntryStart)
# text input field - End value
self.entry_end = QLineEdit(self)
self.entry_end.setText(str(round(self.end_value, 1)))
self.entry_end.setGeometry(QtCore.QRect(320, 80, 50, 25))
self.entry_end.textChanged[str].connect(self.onEntryEnd)
# text input field - number of steps
self.entry_steps = QLineEdit(self)
self.entry_steps.setText(str(int(self.steps_value)))
self.entry_steps.setGeometry(QtCore.QRect(180, 80, 50, 25))
self.entry_steps.textChanged[str].connect(self.onEntrySteps)
# Horizontal slider
self.actuator_slider = QSlider(self) # create horizontalSlider
self.actuator_slider.setOrientation(QtCore.Qt.Horizontal) # orientation horizontal
self.actuator_slider.setGeometry(QtCore.QRect(30, 50, 330, 25)) # position coordinates
self.actuator_slider.setObjectName("horizontalSlider") # object name
self.actuator_slider.setInvertedAppearance(False) # default: right to left
self.actuator_slider.setRange(0, 100) # default: (0, 99)
self.actuator_slider.setValue(self.current_value / self.stepRatio())
self.actuator_slider.valueChanged.connect(self.onActuatorSlider)
# output check box
self.output_check = QCheckBox(self)
self.output_check.setGeometry(QtCore.QRect(40, 120, 300, 25))
self.output_check.setChecked(False)
self.output_check.setText("Check to record an image sequence")
self.output_check.setObjectName("checkBoxOutput")
self.output_check.clicked.connect(self.onOutputClicked)
# forward button
self.forward_button = QPushButton(">->", self)
self.forward_button.setGeometry(QtCore.QRect(240, 80, 50, 25))
self.forward_button.setAutoDefault(False)
self.forward_button.clicked.connect(self.onForward)
# backward button
self.backward_button = QPushButton("<-<", self)
self.backward_button.setGeometry(QtCore.QRect(100, 80, 50, 25))
self.backward_button.setAutoDefault(False)
self.backward_button.clicked.connect(self.onBackward)
# close button
self.close_button = QPushButton("Close window", self)
self.close_button.setGeometry(QtCore.QRect(120, 160, 130, 25))
self.close_button.setAutoDefault(False)
self.close_button.clicked.connect(self.onClose)
# now make the window visible
self.show()
def getDriverType(self, constraint):
ANGLE_CONSTRAINTS = [
"Angle",
"PlaneCoincident",
"AxialAlignment",
"PlaneAlignment"
]
DISTANCE_CONSTRAINTS = [
"PointDistance",
"PointsDistance"
]
if constraint.ConstraintType in ANGLE_CONSTRAINTS:
return "Angle"
elif constraint.ConstraintType in DISTANCE_CONSTRAINTS:
return "Distance"
else:
return "Length"
def stepRatio(self):
ratio = (self.end_value - self.start_value) / 100
return ratio
def onEntryStart(self, new_start):
self.start_value = float(new_start)
self.label_start.setText(str(round(self.start_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
def onEntryEnd(self, new_end):
self.end_value = float(new_end)
self.label_end.setText(str(round(self.end_value, 1)) + self.unit_suffix)
# Update the slider
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
def onEntrySteps(self, new_steps):
self.steps_value = int(new_steps)
def onActuatorSlider(self, slider_value):
self.current_value = slider_value * self.stepRatio() + self.start_value
if self.driver_type == "Angle":
self.actuator.Angle = self.current_value
elif self.driver_type == "Distance":
self.actuator.Distance = self.current_value
else:
self.actuator.Offset = self.current_value
self.label_current.setText("Current value: " + str(round(self.current_value, 1)) + self.unit_suffix)
FreeCADGui.updateGui() # screen update between steps
Gui.runCommand("asm3CmdQuickSolve", 0)
def onForward(self):
steps_left = self.steps_value
print(self.steps_value)
step = ((self.end_value - self.current_value) / steps_left)
while steps_left > 0:
self.current_value += step
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
time.sleep(0.2)
self.output(steps_left)
steps_left -= 1
self.actuator_slider.setValue(100)
def onBackward(self):
steps_left = self.steps_value
step = ((self.current_value - self.start_value) / steps_left)
while steps_left > 0:
self.current_value -= step
slider_value = ((self.current_value - self.start_value) / self.stepRatio())
self.actuator_slider.setValue(slider_value)
time.sleep(0.2)
self.output(steps_left)
steps_left -= 1
self.actuator_slider.setValue(0)
def onClose(self):
self.result = "Closed"
self.close()
def onOutputClicked(self):
if self.sequence == True:
self.sequence = False
self.output_check.setChecked(False)
else:
self.sequence = True
self.output_check.setChecked(True)
def output(self, counter):
if (self.sequence == True):
image_path = ".../FreeCAD/ScreenShots/Sequence"
file_tag = ".png"
height = 640
width = 480
background = "Transparent"
# dealing with leading zeros
if (counter > 999) or (counter < 0):
print("Out of Range")
elif (counter < 10):
number = "00" + str(counter)
elif (counter < 100):
number = "0" + str(counter)
else:
number = str(counter)
# Screen shot
Gui.activeDocument().activeView().saveImage(image_path + number + file_tag, height, width, background)
# End of ControlPanel()
# Main section below:
def findTheDrivingConstraints(document_object):
# search through the Objects and find the driving constraint
driver_list = []
for each in document_object.Objects:
if each.Label.endswith("Driver"):
driving_constraint = each.Name
driver_list.append(driving_constraint)
return driver_list
def main():
kin_doc = App.ActiveDocument # Kinematic Document
drivers = findTheDrivingConstraints(kin_doc)
if len(drivers) < 1:
print("No driver found!")
else:
panel_list = []
for each_driver in drivers:
panel = ControlPanel(kin_doc, each_driver)
panel_list.append(panel)
panel.exec_()
if __name__ == "__main__":
# This will be true only if the file is "executed"
# but not if imported as a module
main()
Kilka niedoskonałości
- Kolejność sekwencji obrazów jest odwrócona, ponieważ używamy zmiennej steps_left, która jest odliczana.
- Katalog obrazów i nazwa obrazu są zakodowane na sztywno.
- Wiele kontrolerów nie jest zsynchronizowanych.