Translations:Draft tutorial/75/ru: Difference between revisions

From FreeCAD Documentation
No edit summary
No edit summary
Line 1: Line 1:
4. Мы создадим дуги и линии.
4. Создадим дуги и линии.
:4.1. Нажмите {{Button|[[File:Draft_Arc.svg|16px]] [[Draft_Arc/ru|Arc]]}}.
:4.1. Нажмите {{Button|[[File:Draft_Arc.svg|16px]] [[Draft_Arc/ru|Дуга]]}}.
:4.2. Установите {{MenuCommand|Center}} в{{Value|(0, 0, 0)}}, и нажмите {{KEY|Enter}}.
:4.2. Установите {{MenuCommand|Центр}} в {{Value|(0, 0, 0)}}, и нажмите {{KEY|Enter}}.
:4.3. Установите {{MenuCommand|Radius}} в {{Value|30 mm}}, и нажмите {{KEY|Enter}}.
:4.3. Установите {{MenuCommand|Радиус}} в {{Value|30 mm}}, и нажмите {{KEY|Enter}}.
:4.4. Установите {{MenuCommand|Start angle}} в {{Value|60.0°}}, и нажмите {{KEY|Enter}}.
:4.4. Установите {{MenuCommand|Начальный угол}} в {{Value|60.0°}} и нажмите {{KEY|Enter}}.
:4.5. Установите {{MenuCommand|Aperture angle}} to {{Value|60.0°}}, и нажмите {{KEY|Enter}}.
:4.5. Установите {{MenuCommand|Угол апертуры}} в {{Value|60.0°}} и нажмите {{KEY|Enter}}.
:4.6. Повторите эту процедуру для следующей дуги с радиусом {{Value|25 mm}}, остальные параметры те же
:4.6. Повторите эту процедуру для следующей дуги с радиусом {{Value|25 мм}}, остальные параметры те же.

Revision as of 10:38, 16 March 2021

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Draft tutorial)
4. We will create arcs and lines.
:4.1. Press {{Button|[[File:Draft_Arc.svg|16px]] [[Draft_Arc|Arc]]}}.
:4.2. Set the {{MenuCommand|Center}} to {{Value|(0, 0, 0)}}, and press {{KEY|Enter}}.
:4.3. Set the {{MenuCommand|Radius}} to {{Value|30 mm}}, and press {{KEY|Enter}}.
:4.4. Set the {{MenuCommand|Start angle}} to {{Value|60.0°}}, and press {{KEY|Enter}}.
:4.5. Set the {{MenuCommand|Aperture angle}} to {{Value|60.0°}}, and press {{KEY|Enter}}.
:4.6. Repeat the same procedure for a second arc with a radius of {{Value|25 mm}}, the other properties are the same.

4. Создадим дуги и линии.

4.1. Нажмите Дуга.
4.2. Установите Центр в (0, 0, 0), и нажмите Enter.
4.3. Установите Радиус в 30 mm, и нажмите Enter.
4.4. Установите Начальный угол в 60.0° и нажмите Enter.
4.5. Установите Угол апертуры в 60.0° и нажмите Enter.
4.6. Повторите эту процедуру для следующей дуги с радиусом 25 мм, остальные параметры те же.