Translations:Draft Wire/5/tr: Difference between revisions

From FreeCAD Documentation
(Created page with "== Seçenekler == *Birden çok Çizgi seçilir ve '''Tel''' tıklanırsa, çizgiler tele dönüşür ve komuttan çıkılır. {{Version/tr|0.17}} *Teli bitir...")
(No difference)

Revision as of 10:43, 3 January 2019

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Draft Wire)
* To manually enter coordinates enter the X, Y and Z component, and press {{KEY|Enter}} after each. Or you can press the {{Button|[[Image:Draft_AddPoint.svg|16px]] Enter point}} button when you have the desired values. It is advisable to move the pointer out of the [[3D_view|3D view]] before entering coordinates.
* Press {{KEY|R}} or click the {{MenuCommand|Relative}} checkbox to toggle relative mode. If relative mode is on, coordinates are relative to the last point, if available, else they are relative to the coordinate system origin.
* Press {{KEY|G}} or click the {{MenuCommand|Global}} checkbox to toggle global mode. If global mode is on, coordinates are relative to the global coordinate system, else they are relative to the [[Draft_SelectPlane|working plane]] coordinate system. {{Version|0.20}}
* Press {{KEY|F}} or click the {{MenuCommand|Filled}} checkbox to toggle filled mode. If filled mode is on, the created wire will have {{PropertyData|Make Face}} set to {{TRUE}} and will have a filled face, provided it is closed and does not self-intersect. Note that a self-intersecting wire with a face will not display properly, for such a wire {{PropertyData|Make Face}} must be set to {{FALSE}}.
* Press {{KEY|N}} or click the {{MenuCommand|Continue}} checkbox to toggle continue mode. If continue mode is on, the command will restart after using {{Button|[[Image:Draft_FinishLine.svg|16px]] Finish}} or {{Button|[[Image:Draft_CloseLine.svg|16px]] Close}}, or after creating a closed wire by snapping to the first point of the wire, allowing you to continue creating wires.
* Press {{KEY|/}} or the {{Button|[[Image:Draft_UndoLine.svg|16px]] Undo}} button to undo the last point.
* Press {{KEY|A}} or the {{Button|[[Image:Draft_FinishLine.svg|16px]] Finish}} button to finish the command and leave the wire open.
* Press {{KEY|O}} or the {{Button|[[Image:Draft_CloseLine.svg|16px]] Close}} button to finish the command and close the wire. A closed wire can also be created by snapping to the first point of the wire.
* Press {{KEY|W}} or the {{Button|[[Image:Draft Wipe.svg|16px]] Wipe}} button to delete the segments already placed, but keep working from the last point.
* Press {{KEY|U}} or the {{Button|[[Image:Draft SelectPlane.svg|16px]] [[Draft_SelectPlane|Set WP]]}} button to adjust the current working plane in the orientation of the last segment.
* Press {{KEY|S}} to switch [[Draft_Snap|Draft snapping]] on or off.
* Press {{KEY|Esc}} or the {{Button|Close}} button to finish the command.

Seçenekler

  • Birden çok Çizgi seçilir ve Tel tıklanırsa, çizgiler tele dönüşür ve komuttan çıkılır. 0.17 sürümünde kullanılabilir
  • Teli bitirmek için F veya Bitir düğmesine basın.
  • C veya Kapat düğmesine basın veya bitirmek için ilk noktaya tıklayın tel, ancak son nokta ile birincinin arasına son bir parça ekleyerek kapatılır.
  • Verilen eksendeki bir sonraki noktayı sınırlamak için bir noktadan sonra X, Y veya Z tuşlarına basın.