All translations
Enter a message name below to show all available translations.
Found 3 translations.
Name | Current message text |
---|---|
h English (en) | # Activate the [[Image:PartDesign_Body.svg|24px]] [[PartDesign_Body|PartDesign Body]]. This will also activate the [[Image:Workbench_PartDesign.svg|24px]] [[PartDesign_Workbench|PartDesign Workbench]], if required. # In the [[3D_view|3D view]] select the correct face belonging to the body. # Create a new sketch with the [[Image:PartDesign_NewSketch.svg|24px]] [[PartDesign_NewSketch|PartDesign NewSketch]] command. # The sketch will be attached to the selected face. # Call the [[Image:Sketcher_External.svg|24px]] [[Sketcher_External|Sketcher External]] command. # Select three circular edges (holes) from the body. # Use the [[Image:Sketcher_Create3PointCircle.svg|24px]] [[Sketcher_Create3PointCircle|Sketcher Create3PointCircle]] command to create a circle constrained to the center points of the external geometry. # The sketch should now be fully constrained. # Close the sketch. |
h français (fr) | # Activez le [[Image:PartDesign_Body.svg|24px]] [[PartDesign_Body/fr|PartDesign Corps]]. Cela activera également l'[[Image:Workbench_PartDesign.svg|24px]] [[PartDesign_Workbench/fr|atelier PartDesign]], si nécessaire. # Dans la [[3D_view/fr|vue 3D]], sélectionnez la bonne face appartenant au corps. # Créez une nouvelle esquisse avec l'icône [[Image:PartDesign_NewSketch.svg|24px]] [[PartDesign_NewSketch/fr|PartDesign Nouvelle esquisse]]. # L'esquisse sera attachée à la face sélectionnée. # Lancez la commande [[Image:Sketcher_External.svg|24px]] [[Sketcher_External/fr|Sketcher Géométrie externe]]. # Sélectionnez trois arêtes circulaires (trous) dans le corps. # Utilisez la commande [[Image:Sketcher_Create3PointCircle.svg|24px]] [[Sketcher_External/fr|Sketcher Géométrie externe]]. Utilisez la commande [[Sketcher_Create3PointCircle/fr|Sketcher Création d'un cercle par 3 points]] pour créer un cercle contraint aux points centraux de la géométrie externe. # L'esquisse doit maintenant être entièrement contrainte. # Fermez l'esquisse. |
h polski (pl) | # Aktywuj [[Image:PartDesign_Body.svg|24px]] [[PartDesign_Body/pl|Zawartość]]. # Spowoduje to uruchomienie środowiska pracy [[Image:Workbench_PartDesign.svg|24px]] [[PartDesign_Workbench/pl|Projekt Części]], jeśli będzie wymagane. # W oknie [[3D_view/pl|widoku 3D]] wybierz odpowiednią ścianę należącą do zawartości. # Utwórz nowy szkic za pomocą polecenia [[Image:PartDesign_NewSketch.svg|24px]] [[PartDesign_NewSketch/pl|Utwórz szkic]]. # Szkic zostanie dołączony do wybranej ściany. # Wywołaj polecenie [[Image:Sketcher_External.svg|24px]] [[Sketcher_External/pl|Geometria zewnętrzna]]. # Wybierz trzy okrągłe krawędzie ''(otwory)'' z zawartości. # Użyj polecenia [[Image:Sketcher_Create3PointCircle.svg|24px]][[Sketcher_Create3PointCircle/pl|Utwórz okrąg]], aby utworzyć okrąg związany do punktów środkowych geometrii zewnętrznej. # Szkic powinien być teraz w pełni związany. # Zamknij szkic. |