FCGear: Corona dentata
Corona dentata |
Posizione nel menu |
---|
Gear → Crown Gear |
Ambiente |
FCGear |
Avvio veloce |
None |
Introdotto nella versione |
v0.16 |
Vedere anche |
Ingranaggio ad evolvente |
Descrizione
La ruota dentata ricorda una cremagliera curva a forma di anello. L'angolo di pressione diminuisce continuamente dal diametro esterno a quello interno. In questo modo la velocità periferica variabile della corona dentata viene compensata con la velocità periferica costante del pignone. I denti esterni appuntiti e i fianchi ripidi del dente sul diametro interno limitano la larghezza utile del dente. Gli ingranaggi a corona raggiungono efficienze simili agli ingranaggi cilindrici. Una corona dentata può azionare più pignoni.
Campi di applicazione noti per le corone dentate:
- Azionamenti dell'asse posteriore per auto e moto
- Meccanismo girevole per tavoli operatori
- Teste per fresatura angolare
- Sistemi di utensili motorizzati con pignoni multipli e corona dentata
Sopra: corona dentata
Utilizzo
- Passare a FCGear.
- Esistono diversi modi per richiamare il comando:
- Premere il pulsante Crown Gear nella barra degli strumenti.
- Selezionare l'opzione Gear → Crown Gear dal menu.
- Per default la corona dentata viene visualizzata senza denti. (disponibile dalla versione 0.21)
- Modificare i parametri dell'ingranaggio alle condizioni richieste (vedere Proprietà).
- Impostare la proprietà Datipreview_mode su
false
per visualizzare i denti (vedere Note).
Proprietà
Un oggetto FCGear CrownGear deriva da un oggetto Part Feature e ne eredita tutte le proprietà. Ha inoltre le seguenti proprietà aggiuntive:
Dati
accuracy
- Datinum_profiles (
Integer
): L'impostazione predefinita è4
. Numero di profili utilizzati per il loft. - Datipreview_mode (
Bool
): il valore predefinito ètrue
.
base
- Datiheight (
Length
): Default is2 mm
. Value for the tooth width. - Datimodule (
Length
): Default is1 mm
. Module is the ratio of the reference diameter of the gear divided by the number of teeth (see Notes). - Datiother_teeth (
Integer
): Default is15
. Number of teeth of the construction gear (pinion) (see Notes). - Datiteeth (
Integer
): Default is15
. Number of teeth. - Datithickness (
Length
): Default is5 mm
. Height from the tip of tooth to the lower side of the crown wheel.
involute
- Datipressure_angle (
Angle
): Default is20 °
(see Notes).
version
- Dativersion (
String
):
Note
- The Datipreview_mode property is set to
true
by default and when the gear is created you'll find this message in the report view:- Gear module: Crown gear created, preview_mode = true for improved performance. Set preview_mode property to false when ready to cut teeth.
- module: Using ISO (International Organization for Standardization) guidelines, Module size is designated as the unit representing gear tooth-sizes. Module (m): m = 1 (p = 3.1416), m = 2 (p = 6.2832), m = 4 (p = 12.566). If you multiply Module by Pi, you can obtain Pitch (p). Pitch is the distance between corresponding points on adjacent teeth.
- other_teeth: Several pinions with the same number of teeth only can be used on one crown wheel.
- pressure_parameter: Only change the parameter, if sufficient knowledge of the gear geometry is available.
- The geometry of the crown gear is primarily determined by the spur pinion geometry (other_teeth).
- Create spur gear with Involute gear. The number of teeth must be identical to the parameter other_teeth of the crown gear.
- Adjustments for optimal running characteristics can be made with the parameters of involute gear.
Panoramica dell'insieme corona e ingranaggio cilindrico
- (1) Spur gear
- (2) Crown gear
- (3) Tooth width
- (4) Inner diameter
- (5) Outer diameter
Formule utili
- Inner diameter (4)
- inner diamter = module (spur gear) * teeth (crown gear) * cos pressure_paramter (pinion) : cos pressure_parameter (crown gear)
- Outer diameter (5)
- outer diamter = inner diameter + 2x height (tooth width crown gear)