Sketcher Split/ru: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
 
Line 29: Line 29:
Данный инструмент позволяет разделить ребро на две абсолютно одинаковые части, с сохранением большинства ограничений. Ограничения сохраняются для вновь созданных ребер, за исключением точки в которой произошло разделение. Окружность в случае её разделения, делится на дуги концы которых не связанны между собой, при этом ограничения которые имела окружность, переносятя на вновь созданные созданные дуги.
Данный инструмент позволяет разделить ребро на две абсолютно одинаковые части, с сохранением большинства ограничений. Ограничения сохраняются для вновь созданных ребер, за исключением точки в которой произошло разделение. Окружность в случае её разделения, делится на дуги концы которых не связанны между собой, при этом ограничения которые имела окружность, переносятя на вновь созданные созданные дуги.
</div>
</div>

[[File:SketcherSplitExample1.png]] [[File:SketcherSplitExample2.png]] [[File:SketcherSplitExample3.png]]


<span id="Usage"></span>
<span id="Usage"></span>
== Применение ==
== Применение ==

See also: [[Sketcher_Workbench#Drawing_aids|Drawing aids]].


<div class="mw-translate-fuzzy">
<div class="mw-translate-fuzzy">
Line 41: Line 41:
# Нажатие {{KEY|Esc}} или нажатие правой кнопки мыши завершит работу функции.
# Нажатие {{KEY|Esc}} или нажатие правой кнопки мыши завершит работу функции.
</div>
</div>

<span id="Limitations"></span>
== Ограничения ==

* In {{VersionMinus|0.20}} the action is not supported for ellipses, parabolas, hyperbolas and B-splines.


<span id="Notes"></span>
<span id="Notes"></span>
== Примечания ==
== Примечания ==


* A [[Sketcher_ConstrainCoincident|Coincident]] constraint is applied to the center points of new arcs.
* All coincidences are transferred - start point, end point and center point (if applicable).
* [[Sketcher_ConstrainRadius|Radius]] and [[Sketcher_ConstrainDiameter|Diameter]] constraints are copied to new arcs (resulting in a redundancy).
* Point on object constraint is transferred to the closer newly created edge.
* Vertical and horizontal constraints are copied to both offsprings.
* Coincident constraints and [[Sketcher_ConstrainPointOnObject|Point on object]] constraints are transferred to the closest new edge.
* [[Sketcher_ConstrainHorizontal|Horizontal]] and [[Sketcher_ConstrainVertical|Vertical]] constraints between points are transferred to the closest new edge.
* Parallel and perpendicular constraints are copied for both line segments, for arc only once, to the closer part.
* Equality constraint is transferred only for resulting arc edges, line segments do not receive it.
* Horizontal and Vertical constraints attached to lines are copied to new line segments.
* [[Sketcher_ConstrainParallel|Parallel]] and [[Sketcher_ConstrainPerpendicular|Perpendicular]] constraints are copied to new line segments, for new arcs they are only copied to the closest.
* Symmetry constraint is currently not transferred.
* [[Sketcher_ConstrainDistanceX|Horizontal distance]], [[Sketcher_ConstrainDistanceY|Vertical distance]] and [[Sketcher_ConstrainDistance|Distance]] constraints are transferred to the closest new edge.
* Block constraint is currently not transferred.
* [[Sketcher_ConstrainAngle|Angle]], [[Sketcher_ConstrainSymmetric|Symmetric]] and [[Sketcher_ConstrainBlock|Block]] constraints are currently not transferred.
* Horizontal, vertical and length constraints between points are transferred to the outer points of the new edges.
* Point distance constraint is assigned only once, to the closer edge segment.
* Radius and diameter constraints are copied to any resulting arc.
* Angle constraint is currently not transferred





Latest revision as of 10:09, 13 April 2024

Разделить ребро

Системное название
Sketcher_Split
Расположение в меню
Sketch → Геометрия эскиза → Разделить ребро
Верстаки
Sketcher
Быстрые клавиши
Нет
Представлено в версии
0.20
См. также
Обрезать кривую

Описание

Данный инструмент позволяет разделить ребро на две абсолютно одинаковые части, с сохранением большинства ограничений. Ограничения сохраняются для вновь созданных ребер, за исключением точки в которой произошло разделение. Окружность в случае её разделения, делится на дуги концы которых не связанны между собой, при этом ограничения которые имела окружность, переносятя на вновь созданные созданные дуги.

Применение

See also: Drawing aids.

  1. Нажмите кнопку Разделить. Указатель мыши примет форму белого перекрестия с значком разделения.
  2. Кликните на ребро в том месте, где вы хотите его разделить.
  3. Ребра в форме линии или дуги будут поделены на два новых фрагмента, соединенных точкой в месте разделения. Окружность будет разделена на дуги с той же центральной точкой и другими ограничениями, которые были у исходной окружности.
  4. Нажатие Esc или нажатие правой кнопки мыши завершит работу функции.

Примечания

  • A Coincident constraint is applied to the center points of new arcs.
  • Radius and Diameter constraints are copied to new arcs (resulting in a redundancy).
  • Coincident constraints and Point on object constraints are transferred to the closest new edge.
  • Horizontal and Vertical constraints between points are transferred to the closest new edge.
  • Horizontal and Vertical constraints attached to lines are copied to new line segments.
  • Parallel and Perpendicular constraints are copied to new line segments, for new arcs they are only copied to the closest.
  • Horizontal distance, Vertical distance and Distance constraints are transferred to the closest new edge.
  • Angle, Symmetric and Block constraints are currently not transferred.