Jump to content

Editing Translations:SheetMetal AddFoldWall/18/fr

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (SheetMetal AddFoldWall)
# Create a blank
## Select the outline sketch 
## Press the {{Button|[[Image:SheetMetal_AddBase.svg|16px]][[SheetMetal_AddBase|Make Base Wall]]}} button </br> or use the keyboard shortcut: {{KEY|C}} then {{KEY|B}} </br> [[Image:SheetMetal_AddFoldWall-02.png|120px]] [[Image:SheetMetal_AddFoldWall-03.png|280px]] {{Caption|(The blank is padded in z direction and so it has to be flipped </br> each time, to select the bottom face that is lying on the sketch plane)}} </br>
# Fold the tip 
## Select the blank's '''bottom face''' 
## Select the '''sketch''' named '''''Tip Fold line''''' (preferably from the Tree View) </br> (and don't forget the control/command key ) 
## Press the {{Button|[[Image:SheetMetal_AddFoldWall.svg|16px]] [[SheetMetal_AddFoldWall|Fold a wall]]}} button </br> or use the keyboard shortcut: {{KEY|C}} then {{KEY|F}} </br>[[Image:SheetMetal_AddFoldWall-10.png|120px]] [[Image:SheetMetal_AddFoldWall-04.png|120px]] [[Image:SheetMetal_AddFoldWall-05.png|280px]]
## The fold should be 90° down and so some values in the properties window need to be set e.g.: </br> - the '''angle''' value to 60° </br> - the '''invert''' value to true for an upward bend </br> </br>
# Create the downward fold
## Select the blank's '''bottom face'''
## And then the '''sketch''' named '''''Down-Fold line'''''
## Press the {{Button|[[Image:SheetMetal_AddFoldWall.svg|16px]] [[SheetMetal_AddFoldWall|Fold a wall]]}} button </br> or use the keyboard shortcut: {{KEY|C}} then {{KEY|F}} </br>[[Image:SheetMetal_AddFoldWall-11.png|120px]] [[Image:SheetMetal_AddFoldWall-06.png|120px]] [[Image:SheetMetal_AddFoldWall-07.png|280px]]
## Set the '''angle''' value to 92°
## If the wrong section of the part moved set the '''invertbend''' value to true </br> </br>
# To create the upward fold
## select the blank's '''bottom face'''
## and then the '''sketch''' named '''''Up-Fold line''''' 
## Press the {{Button|[[Image:SheetMetal_AddFoldWall.svg|16px]] [[SheetMetal_AddFoldWall|Fold a wall]]}} button </br> or use the keyboard shortcut: {{KEY|C}} then {{KEY|F}} </br>[[Image:SheetMetal_AddFoldWall-12.png|120px]] [[Image:SheetMetal_AddFoldWall-08.png|120px]] [[Image:SheetMetal_AddFoldWall-09.png|280px]]
## Set the '''angle''' value to 80°
## If the fold is downward set the '''invert''' value to true
## If needed set the '''invertbend''' value to true </br> </br>
Done!
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

Please note that all contributions to FreeCAD Documentation are considered to be released under the Creative Commons Attribution (see FreeCAD:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

Formatting help

Cancel Editing help (opens in new window)

Templates used on this page: