FEM Elastizitätsgleichung

From FreeCAD Documentation
This page is a translated version of the page FEM EquationElasticity and the translation is 28% complete.

FEM Elastizitätsgleichung

Menüeintrag
Lösen → Mechanical equations → Elasticity equation
Arbeitsbereich
FEM
Standardtastenkürzel
Keiner
Eingeführt in Version
0.17
Siehe auch
Verformungsgleichung equation, FEM Anleitung

Beschreibung

Diese Gleichung beschreibt die mechanischen Eigenschaften von Festkörpern.

For info about the math of the equation, see the Elmer models manual, section Linear Elasticity.

Anwendung

  1. After adding an Elmer solver as described here, select it in the tree view.
  2. Now either use the toolbar button or the menu Solve → Mechanical equations → Elasticity equation.
  3. Change the equation's solver settings or the general solver settings if necessary.

Note: For analyses of nonlinear elasticity you must use the Deformation equation (introduced in version 0.21). The Elasticity equation is only for linear elasticity.

Note: If you use more than one CPU core for the solver (introduced in version 0.21), you cannot use the default solver settings. However, using just one CPU and the default solver settings is in many cases faster than using several CPUs because the elasticity solver is only fast when DatenLinear Solver Type is set to Direct (the default, described here). For multi-CPU solving one can only use the DatenLinear Direct Method MUMPS. However, MUMPS is not freely available as a direct download.

Solver Settings

For the general solver settings, see the Elmer solver settings.

The elasticity equation provides these special settings:

  • DatenCalculate Pangle: If the principal angles should be calculated.
  • DatenCalculate Principal: If all stresses should be calculated.
  • DatenCalculate Strains: If strains will be calculated. This will also calculate the stresses, even if DatenCalculate Principal or DatenCalculate Stresses is false.
  • DatenCalculate Stresses: If stresses should be calculated. Compared to DatenCalculate Principal the Tresca yield criterion and the principal stress will not be calculated.
  • DatenConstant Bulk System: See the Elmer manual for more info.
  • DatenDisplace Mesh: If mesh can be deformed. This is by default true and must be set to false for eigenfrequency analyses.
  • DatenFix Displacement: If displacements or forces are set. thereby DatenModel Lumping is automatically used.
  • DatenGeometric Stiffness: Considers the geometric stiffness of the body.
  • DatenIncompressible: Computation of incompressible material in connection with viscoelastic Maxwell material and a custom DatenVariable.
  • DatenMaxwell Material: Compute the viscoelastic material model.
  • DatenModel Lumping: Uses model lumping.
  • DatenModel Lumping Filename: File to save the results from the model lumping.
  • DatenStability Analysis: If true DatenEigen Analysis becomes a stability analysis (buckling analysis). Otherwise a modal analysis is performed.
  • DatenUpdate Transient System: See the Elmer manual for more info.
  • DatenVariable: The variable for the elasticity equation. Only change this if DatenIncompressible is set to true in accordance to the Elmer manual.

Eigenvalues:

  • DatenEigen Analysis: If an eigen analysis should be performed (calculation of eigenmodes and eigenfrequencies).
  • DatenEigen System Complex: Should be true if the eigen system is complex. it must be false for a damped eigen value analyses.
  • DatenEigen System Compute Residuals: Computes residuals of the eigen value system.
  • DatenEigen System Damped: Set a damped eigen analysis. Can only be used if DatenLinear Solver Type is Iterative.
  • DatenEigen System Select: Selection of which eigenvalues are computed. Note that the selection of Largest* cause an infinite run for recent Elmer solver (as of August 2022).
  • DatenEigen System Tolerance: Convergence tolerance for iterative eigensystem solve. The default is 100 times the DatenLinear Tolerance.
  • DatenEigen System Values: The number of the highest eigenmode that should be calculated.

Equation:

  • DatenPlane Stress: Computes solution according to the plane stress situation. Applies only for 2D geometry.

Analysis Feature Information

The elasticity equation takes the following analysis features into account if they are set:

Hinweis

  • Except for calculations in 2D, for all the above analysis features it is important that they act on a face. Features in 3D set to lines or vertices are not recognized by the Elmer solver.

Eigenmode Analysis

To perform an eigenmode analysis (calculation if the eigenmodes and eigenfrequencies), you need to

  1. Set DatenEigen Analysis to true
  2. Set DatenDisplace Mesh to false
  3. Set DatenEigen System Values to the highest number of eigenmodes you are interested in. The smaller this number the shorter the solver runtime since higher modes can be omitted from computation.
  4. Add a fixed boundary condition and set at least one face of the body as fixed.
  5. Run the solver.

It is highly recommended to use DatenLinear Solver Type set to Direct (the default) because this is much faster and the results are more accurate.

Buckling Analysis

To perform a buckling analysis, you need to do the same as for an Eigenmode Analysis, and additionally:

  • Set DatenStability Analysis to true

Ergebnisse

The available results depend on the solver settings. If none of the DatenCalculate * settings was set to true, only the displacement is calculated. Otherwise also the corresponding results will be available. If DatenEigen Analysis was set to true all results will be available for every calculated eigenmode.

If DatenEigen Analysis was set to true, the eigenfrequencies are output at the end of the solver log in the solver dialog and also in the document SolverElmerOutput that will be created in the tree view after the solver has finished.

Note: The eigenmode displacement vector has an arbitrary value since the result is

whereas is the eigenvector and is a complex number.