Draft OrthoArray/it: Difference between revisions

From FreeCAD Documentation
(Created page with "Il comando Serie ortogonale, il comando Serie polare e il comando Serie circolare creano lo stesso oggetto. Questo oggetto è derivato da un oggetto Part Feature e ne eredita tutte le proprietà (ad eccezione di alcune proprietà della vista che non sono ereditate dagli serie di link). Le seguenti proprietà sono aggiuntive se non diversamente specificato:")
(Created page with "===Dati===")
Line 76: Line 76:
Il comando Serie ortogonale, il comando [[Draft_PolarArray/it|Serie polare]] e il comando [[Draft_CircularArray/it|Serie circolare]] creano lo stesso oggetto. Questo oggetto è derivato da un oggetto [[Part_Feature/it|Part Feature]] e ne eredita tutte le proprietà (ad eccezione di alcune proprietà della vista che non sono ereditate dagli serie di link). Le seguenti proprietà sono aggiuntive se non diversamente specificato:
Il comando Serie ortogonale, il comando [[Draft_PolarArray/it|Serie polare]] e il comando [[Draft_CircularArray/it|Serie circolare]] creano lo stesso oggetto. Questo oggetto è derivato da un oggetto [[Part_Feature/it|Part Feature]] e ne eredita tutte le proprietà (ad eccezione di alcune proprietà della vista che non sono ereditate dagli serie di link). Le seguenti proprietà sono aggiuntive se non diversamente specificato:


===Data===
<span id="Data"></span>
===Dati===


{{TitleProperty|Link}}
{{TitleProperty|Link}}

Revision as of 21:30, 14 May 2023

Serie ortogonale

Posizione nel menu
Modifiche → Strumenti serie → Serie ortogonale
Ambiente
Draft, Arch
Avvio veloce
Nessuno
Introdotto nella versione
0.19
Vedere anche
Serie polare, Serie circolare, Serie su tracciato, Serie di link su tracciato, Serie su punti, Serie di link su punti

Descrizione

Il comando Serie ortogonale crea una serie (array) ortogonale (3 assi) da un oggetto selezionato. Il comando può facoltativamente creare un array Link, che è più efficiente di un normale array.

Il comando può essere utilizzato su oggetti 2D creati con Draft o Sketcher, ma anche su molti oggetti 3D come quelli creati con gli ambienti Part, PartDesign o Arch.

Serie ortogonale

Utilizzo

  1. Facoltativamente selezionare un oggetto.
  2. Esistono diversi modi per invocare il comando:
    • Premere il pulsante Serie ortogonale.
    • Selezionare l'opzione Modifiche → Strumenti array → Serie ortogonale dal menu.
  3. Si apre il pannello attività Serie ortogonale. Vedi Opzioni per maggiori informazioni.
  4. Se non si ha ancora selezionato un oggetto: selezionare un oggetto.
  5. Immettere i parametri richiesti nel pannello delle attività.
  6. Per completare il comando, eseguire una delle seguenti operazioni:
    • Fare clic nella Vista 3D.
    • Premere Enter.
    • Premere il pulsante OK.

Opzioni

  • Inserire il Numero di elementi per le direzioni X, Y e Z. Questo numero deve essere almeno 1 per ogni direzione.
  • Immettere Intervalli X per specificare lo spostamento degli elementi nella direzione X. Per una serie rettangolare i valori Y e Z devono essere 0.
  • Immettere Intervalli Y per specificare lo spostamento degli elementi nella direzione Y. Per una serie rettangolare i valori X e Z devono essere 0.
  • Immettere Intervalli Z per specificare lo spostamento degli elementi nella direzione Z. Per una serie rettangolare i valori X e Y devono essere 0.
  • Premere il pulsante Reset X, Y o Z per reimpostare lo spostamento nella direzione data ai valori predefiniti.
  • Se la casella di controllo Fusione è selezionata, gli elementi sovrapposti nella serie vengono fusi. Questo non funziona per le Serie di link.
  • Se la casella Serie di link è spuntata, viene creato una Serie di Link invece di un normale serie. Una Serie di link è più efficiente perché i suoi elementi sono oggetti App Link.
  • Premere Esc o il pulsante Annulla per interrompere il comando.

Note

  • Una Serie ortogonale può essere trasformata in una Serie polare o in unaSerie circolare modificandone la proprietà DatiArray Type.
  • Una Serie di link non può essere trasformata in una serie normale o viceversa. Il tipo di serie deve essere deciso al momento della creazione.

Preferenze

Vedere anche: Impostare le preferenze e Preferenze per l'ambiente Draft.

  • Per modificare il numero di decimali utilizzati per l'inserimento delle coordinate: Modifica → Preferenze... → Generale → Unità → Impostazioni unità → Numero di cifre decimali.

Proprietà

Vedere anche: Editor delle proprietà.

Il comando Serie ortogonale, il comando Serie polare e il comando Serie circolare creano lo stesso oggetto. Questo oggetto è derivato da un oggetto Part Feature e ne eredita tutte le proprietà (ad eccezione di alcune proprietà della vista che non sono ereditate dagli serie di link). Le seguenti proprietà sono aggiuntive se non diversamente specificato:

Dati

Link

The properties in this group are only available for Link arrays. See Std LinkMake for more information.

  • DatiScale (Float)
  • Dati (Hidden)Scale Vector (Vector)
  • DatiScale List (VectorList)
  • Dati (Hidden)Visibility List (BoolList)
  • Dati (Hidden)Placement List (PlacementList)
  • Dati (Hidden)Element List (LinkList)
  • Dati (Hidden)_ Link Touched (Bool)
  • Dati (Hidden)_ Child Cache (LinkList)
  • Dati (Hidden)Colored Elements (LinkSubHidden)
  • DatiLink Transform (Bool)

Circular array

The properties in this group are hidden for orthogonal arrays and polar arrays.

  • DatiNumber Circles (Integer): specifies the number of circular layers. Must be at least 2.
  • DatiRadial Distance (Distance): specifies the distance between circular layers.
  • DatiSymmetry (Integer): specifies the number of symmetry lines. This number changes the distribution of the elements in the array.
  • DatiTangential Distance (Distance): specifies the distance between elements in the same circular layer. Must be larger than zero.

Objects

  • DatiArray Type (Enumeration): specifies the type of array, which can be ortho, polar or circular.
  • DatiAxis Reference (LinkGlobal): specifies the object and edge to be used instead of the DatiAxis and DatiCenter properties. Not used for orthogonal arrays.
  • DatiBase (Link): specifies the object to duplicate in the array.
  • DatiCount (Integer): (read-only) specifies the total number of elements in the array. version 0.20 and below: Only available for Link arrays.
  • DatiExpand Array (Bool): specifies whether to expand the array in the Tree view to enable the selection of its individual elements. Only available for Link arrays.
  • DatiFuse (Bool): specifies if overlapping elements in the array are fused or not. Not used for Link arrays.

Orthogonal array

The properties in this group are hidden for circular arrays and polar arrays.

  • DatiInterval X (VectorDistance): specifies the interval between elements in the X direction.
  • DatiInterval Y (VectorDistance): specifies the interval between elements in the Y direction.
  • DatiInterval Z (VectorDistance): specifies the interval between elements in the Z direction.
  • DatiNumber X (Integer): specifies the number of elements in the X direction. Must be at least 1.
  • DatiNumber Y (Integer): specifies the number of elements in the Y direction. Must be at least 1.
  • DatiNumber Z (Integer): specifies the number of elements in the Z direction. Must be at least 1.

Polar array

The properties in this group are hidden for circular arrays and orthogonal arrays.

  • DatiAngle (Angle): specifies the aperture of the circular arc. Use 360° for a full circle.
  • DatiInterval Axis (VectorDistance): specifies the interval between elements in the DatiAxis direction.
  • DatiNumber Polar (Integer): specifies the number of elements in the polar direction.

Polar/circular array

The properties in this group are hidden for orthogonal arrays.

  • DatiAxis (Vector): specifies the direction of the axis of the array.
  • DatiCenter (VectorDistance): specifies the center point of the array. The axis of the array passes through this point. For circular arrays it is an offset from the DatiPlacement of the DatiBase object.

View

Link

The properties in this group, with the exception of the inherited property, are only available for Link arrays. See Std LinkMake for more information.

  • VistaDraw Style (Enumeration)
  • VistaLine Width (FloatConstraint)
  • VistaOverride Material (Bool)
  • VistaPoint Size (FloatConstraint)
  • VistaSelectable (Bool): this is an inherited property that appears in the Selection group for other arrays
  • VistaShape Material (Material)

Base

The properties in this group, with the exception of the inherited property, are only available for Link arrays. See Std LinkMake for more information.

  • Vista (Hidden)Child View Provider (PersistentObject)
  • Vista (Hidden)Material List (MaterialList)
  • Vista (Hidden)Override Color List (ColorList)
  • Vista (Hidden)Override Material List (BoolList)
  • Vista (Hidden)Proxy (PythonObject): this is an inherited property.

Display Options

The properties in this group are inherited properties. See Part Feature for more information.

  • VistaBounding Box (Bool): this property is not inherited by Link arrays.
  • VistaDisplay Mode (Enumeration): for Link arrays it can be Link or ChildView. For other arrays it can be: Flat Lines, Shaded, Wireframe or Points
  • VistaShow In Tree (Bool)
  • VistaVisibility (Bool)

Draft

  • VistaPattern (Enumeration): not used.
  • VistaPattern Size (Float): not used.

Object style

The properties in this group are not inherited by Link arrays.

Scripting

See also: Autogenerated API documentation and FreeCAD Scripting Basics.

Parametric array

To create a parametric orthogonal array use the make_array method (introduced in version 0.19) of the Draft module. This method replaces the deprecated makeArray method. The make_array method can create Draft OrthoArrays, Draft PolarArrays and Draft CircularArrays. For each array type one or more wrappers are available.

The main method:

array = make_array(base_object, arg1, arg2, arg3, arg4=None, arg5=None, arg6=None, use_link=True)

The wrappers for orthogonal arrays are:

array = make_ortho_array(base_object,
                         v_x=App.Vector(10, 0, 0), v_y=App.Vector(0, 10, 0), v_z=App.Vector(0, 0, 10),
                         n_x=2, n_y=2, n_z=1,
                         use_link=True)
array = make_ortho_array2d(base_object,
                           v_x=App.Vector(10, 0, 0), v_y=App.Vector(0, 10, 0),
                           n_x=2, n_y=2,
                           use_link=True)

The wrappers for rectangular arrays are:

array = make_rect_array(base_object,
                        d_x=10, d_y=10, d_z=10,
                        n_x=2, n_y=2, n_z=1,
                        use_link=True)
array = make_rect_array2d(base_object,
                          d_x=10, d_y=10,
                          n_x=2, n_y=2,
                          use_link=True)
  • base_object is the object to be arrayed. It can also be the Label (string) of an object in the current document.
  • v_x, v_y, and v_z are the vectors between the base points of the elements in the respective directions.
  • d_x, d_y, and d_z are the distances between the base points of the elements in the respective directions.
  • n_x, n_y, and n_z are the numbers of elements in the respective directions.
  • If use_link is True the created elements are App Links instead of regular copies.
  • array is returned with the created array object.

Example:

import FreeCAD as App
import Draft

doc = App.newDocument()

rect = Draft.make_rectangle(1500, 500)
v_x = App.Vector(1600, 0, 0)
v_y = App.Vector(0, 600, 0)

array = Draft.make_ortho_array2d(rect, v_x, v_y, 3, 4)
doc.recompute()

Non-parametric array

To create a non-parametric orthogonal array use the array method of the Draft module. This method returns None.

array(objectslist, xvector, yvector, xnum, ynum)
array(objectslist, xvector, yvector, zvector, xnum, ynum, znum)

Example:

import FreeCAD as App
import Draft

doc = App.newDocument()

rect = Draft.make_rectangle(1500, 500)
v_x = App.Vector(1600, 0, 0)
v_y = App.Vector(0, 600, 0)

Draft.array(rect, v_x, v_y, 3, 4)
doc.recompute()