All translations

Enter a message name below to show all available translations.

Message

Found 5 translations.

NameCurrent message text
 h Deutsch (de)* Schnittansichten, die auf anderen Schnittansichten basieren, verwenden jetzt standardmäßig die originale (unbeschnittene) Form. Dies kann in den Einstellungen der Schnittansichten geändert werden, um stattdessen die vorhergehende beschnittene Form zu verwenden [https://github.com/FreeCAD/FreeCAD/pull/10281 Pull-Request #10281]
* Hilfsobjekte und Mittellinien können jetzt ausgewählt und durch drücken der Löschtaste entfernt werden. Bisher wurde so die ganze Ansicht gelöscht.[https://github.com/FreeCAD/FreeCAD/pull/10695 Pull-Request #10695] und [https://github.com/FreeCAD/FreeCAD/pull/10813 Pull-Request #10813]
* Ein neues intuitiveres Symbol wurde für das Werkzeug [[TechDraw_WeldSymbol/de|Schweißsymbol]] hinzugefügt. [https://github.com/FreeCAD/FreeCAD/pull/10936 Pull-Request #10936]
* Das Verhalten des Modus Punkt + Kante im Werkzeug [[TechDraw_LengthDimension|Längenmaß]] wurde korrigiert. [https://github.com/FreeCAD/FreeCAD/pull/10860 Pull-Request #10860]
* Der Schaltfläche [[TechDraw_ToggleFrame/de|Ansichtsrahmen ein- oder ausschalten]] wurde ein Aktiviert-Status hinzugefügt, damit der Anwender sehen kann, ob die Schaltfläche aktiviert ist oder nicht.[https://github.com/FreeCAD/FreeCAD/pull/11240 Pull-Request #11240]
* Das Verhalten des Werkzeugs [[TechDraw_DecorateLine/de|LiniendarstellungÄndern]] wurde verbessert. Jetzt wird das Werkzeug (auch) durch Doppelklicken auf einer Linie aufgerufen. Und die Linieneinstellungen werden korrekt wiederhergestellt, wenn der Anwender ''Abbrechen'' drückt. Vorher war kein Unterschied zwischen ''OK'' und ''Abbrechen''. [https://github.com/FreeCAD/FreeCAD/pull/11188 Pull-Request #11188]
* Farbe und Transparenz von Flächen können jetzt pro Ansicht eingetellt werden.[https://github.com/FreeCAD/FreeCAD/pull/11315 Pull-Request #11315]
* Der Mehrfachauswahl-Modus wurde hinzugefügt und kann in den Einstellungen aktiviert werden. In diesem Modus können mehrere Knoten, Kanten oder Flächen durch klicken mit der linken Maustaste ausgewählt werden, ohne dass die Ctrl- bzw. Strg-Taste gedrückt gehalten werden muss. [https://github.com/FreeCAD/FreeCAD/pull/11417 Pull-Request #11417]
* [[TechDraw_ExtensionAreaAnnotation/de|ErgänzungFlächenangabe]] kann jetzt auch beliebige Flächen berechnen. [https://github.com/FreeCAD/FreeCAD/pull/11473 Pull-Request #11473]
* Unterbreochene Linien werden jetzt ISO-/ANSI-Normen entsprechend dargestellt, anstatt nach Qt-Linienstilen. Eine neue Voreinstellung zum Auswählen der Norm wurde hinzugefügt. [https://github.com/FreeCAD/FreeCAD/pull/11594 Pull-Request #11594]
* Das Verhalten des Werkzeugs [[TechDraw_AxoLengthDimension/de|AxonometrischesLängenmaß]] wurde verbessert. Jetzt wird der tatsächliche (3D-) Wert automatisch berechnet und in die Eigenschaft Format Spec (als Text) eingefügt, wenn Kanten parallel zu den globalen Koordinatensystemachsen bemaßt werden. [https://github.com/FreeCAD/FreeCAD/pull/11678 Pull-Request #11678]
* Das Werkzeug [[TechDraw_ExtensionPositionSectionView/de|ErgänzungSchnittAusrichten]] kann jetzt verwendet werden, indem eine Kante in einer Schnittansicht und ein Knoten in der Quellansicht ausgewählt werden.[https://github.com/FreeCAD/FreeCAD/pull/11797 Pull-Request #11797]
* Kleine aber wichtige Verbesserungen für die Bedienbarkeit wurden hinzugefügt - Ein Doppelklick auf ein TechDraw-Zeichnungsblatt öffnet jetzt den Arbeitsbereich und das Werkzeug TechDraw Ansicht verschieben wurde durch einfaches Zeihen und Ablegen in der [[Tree_view/de|Baumansicht ersetzt. Auch die Werkzeuge TechDraw Ansicht zur Ansichtsgruppe hinzufügen]] und TechDraw Ansicht aus Ansichtsgruppe entfernen wurden durch Zeihen und Ablegen in der Baumansicht ersetzt.[https://github.com/FreeCAD/FreeCAD/pull/13063 Pull-Request #13063]
* Die Zeichnungsvorlagen werden jetzt automatisch mit vorhandenen Informationen ausgefüllt (z.B. Datum und Benennung). [https://github.com/FreeCAD/FreeCAD/pull/13005 Pull-Request #13005]
* Das Werkzeug [[TechDraw_ProjectShape/de|Form projizieren]] wurde aus TechDraw entfernt, da es ein Erbe des Arbeitsbereichs Drawing war und nichts mit einem TechDraw-Zeichnungsblatt zu tun hat. [https://github.com/FreeCAD/FreeCAD/pull/13655 Pull-Request #13655]
* Das Werkzeug [[TechDraw_View/de|Ansicht einfügen]] wurde verbessert, und verwendet jetzt mehr Objektarten und Einstellungen. Dies ermöglicht folgende Werkzeuge aus der Symbolleiste zu entfernen: [[TechDraw_SpreadsheetView/de|Tabellenansicht]], [[TechDraw_ArchView/de|ArchAnsicht]], [[TechDraw_Symbol/de|Symbol]], [[TechDraw_Image/de|Bild]] und [[TechDraw_ProjectionGroup/de|Ansichtengruppe]]. [https://github.com/FreeCAD/FreeCAD/pull/13219 Pull-Request #13219]
* Einrasten wurde hinzugefügt, um das automatische Ausrichten von Ansichten und Maßen zu ermöglichen. [https://github.com/FreeCAD/FreeCAD/pull/13659 Pull-Request #13659]
* Der Umgang mit Hilfsgeometrie wurde in vielerlei Hinsicht verbessert. [https://github.com/FreeCAD/FreeCAD/pull/14216 Pull-Request #14216]
 h English (en)* Sections based on other sections now use the original (uncut) shape by default. This can be changed in section settings to use the previous section instead. [https://github.com/FreeCAD/FreeCAD/pull/10281 Pull request #10281]
* Cosmetic objects and centerlines can now be deleted by selecting them and pressing the Delete key. Previously, this resulted in the whole view being deleted. [https://github.com/FreeCAD/FreeCAD/pull/10695 Pull request #10695] and [https://github.com/FreeCAD/FreeCAD/pull/10813 Pull request #10813]
* A new, more intuitive icon was added for the [[TechDraw_WeldSymbol|WeldSymbol]] tool. [https://github.com/FreeCAD/FreeCAD/pull/10936 Pull request #10936]
* The behavior of the point + edge mode of the [[TechDraw_LengthDimension|LengthDimension]] was corrected. [https://github.com/FreeCAD/FreeCAD/pull/10860 Pull request #10860]
* A checked state was added for the [[TechDraw_ToggleFrame|ToggleFrame]] button so that a user can see whether the button is activated or not. [https://github.com/FreeCAD/FreeCAD/pull/11240 Pull request #11240]
* The behavior of the [[TechDraw_DecorateLine|DecorateLine]] tool was improved. Now double-clicking a line invokes this tool. And line styles are correctly restored if the user presses ''Cancel''. Previously, there was no difference between pressing ''OK'' and ''Cancel''. [https://github.com/FreeCAD/FreeCAD/pull/11188 Pull request #11188]
* Color and transparency of faces can now be set per view. [https://github.com/FreeCAD/FreeCAD/pull/11315 Pull request #11315]
* Multiselection mode was added and can be enabled in Preferences. In this mode, multiple vertices, edges and faces can be selected by left-clicking on them, without having to keep the Ctrl key pressed. [https://github.com/FreeCAD/FreeCAD/pull/11417 Pull request #11417]
* [[TechDraw_ExtensionAreaAnnotation|ExtensionAreaAnnotation]] can now calculate areas of arbitrary faces. [https://github.com/FreeCAD/FreeCAD/pull/11473 Pull request #11473]
* Non-continuous lines will now follow the ISO/ANSI standards instead of a Qt line style. A new preference was added to select the standard. [https://github.com/FreeCAD/FreeCAD/pull/11594 Pull request #11594]
* The behavior of the [[TechDraw_AxoLengthDimension|AxoLengthDimension]] tool was improved. Now, when dimensioning edges parallel to the global coordinate system axes, the actual (3D) value is calculated automatically and inserted into the Format Spec property (as text). [https://github.com/FreeCAD/FreeCAD/pull/11678 Pull request #11678]
* The [[TechDraw_ExtensionPositionSectionView|ExtensionPositionSectionView]] tool can now be used by selecting an edge in a section view and a vertex in the source view. [https://github.com/FreeCAD/FreeCAD/pull/11797 Pull request #11797]
* Small but important usability improvements were made - double-clicking on the TechDraw page now enters this workbench and the TechDraw MoveView tool was replaced by simple drag and drop in the [[Tree_view|tree]]. The TechDraw ClipGroupAdd and TechDraw ClipGroupRemove tools were also replaced by tree drag and drop behavior. [https://github.com/FreeCAD/FreeCAD/pull/13063 Pull request #13063]
* The drawing templates are now automatically filled with available information (like date and title). [https://github.com/FreeCAD/FreeCAD/pull/13005 Pull request #13005]
* The [[TechDraw_ProjectShape|Project shape]] tool was removed from TechDraw as it's inherited from the old Drawing workbench and has nothing to do with a TechDraw page. [https://github.com/FreeCAD/FreeCAD/pull/13655 Pull request #13655]
* The [[TechDraw_View|Insert View]] tool was improved so that it can handle more object types and settings. This allowed the following tools to be removed from the toolbar: [[TechDraw_SpreadsheetView|SpreadsheetView]], [[TechDraw_ArchView|ArchView]], [[TechDraw_Symbol|Symbol]], [[TechDraw_Image|Image]] and [[TechDraw_ProjectionGroup|ProjectionGroup]]. [https://github.com/FreeCAD/FreeCAD/pull/13219 Pull request #13219]
* Snapping was added to allow automatic alignment of views and dimensions. [https://github.com/FreeCAD/FreeCAD/pull/13659 Pull request #13659]
* Handling of cosmetics was improved in various ways. [https://github.com/FreeCAD/FreeCAD/pull/14216 Pull request #14216]
 h français (fr)* Les sections basées sur d'autres sections utilisent désormais par défaut la forme originale (non coupée). Ceci peut être modifié dans les paramètres de la section pour utiliser la section précédente à la place. [https://github.com/FreeCAD/FreeCAD/pull/10281 Pull request #10281]
* Les objets cosmétiques et les lignes centrales peuvent désormais être supprimés en les sélectionnant et en appuyant sur la touche Suppr. Auparavant, cela entraînait la suppression de la vue entière. [https://github.com/FreeCAD/FreeCAD/pull/10695 Pull request #10695] et [https://github.com/FreeCAD/FreeCAD/pull/10813 Pull request #10813]
* Une nouvelle icône plus intuitive a été ajoutée pour l'outil [[TechDraw_WeldSymbol/fr|Soudure]]. [https://github.com/FreeCAD/FreeCAD/pull/10936 Pull request #10936]
* Le comportement du mode point + arête de l'outil [[TechDraw_LengthDimension/fr|Cote de longueur]] a été corrigé. [https://github.com/FreeCAD/FreeCAD/pull/10860 Pull request #10860]
* Un état vérifié a été ajouté pour le bouton [[TechDraw_ToggleFrame/fr|Bascule des cadres]] afin qu'un utilisateur puisse voir si le bouton est activé ou non. [https://github.com/FreeCAD/FreeCAD/pull/11240 Pull request #11240]
* Le comportement de l'outil [[TechDraw_DecorateLine/fr|Apparence des lignes]] a été amélioré. Maintenant, double-cliquer sur une ligne appelle cet outil. Et les styles de lignes sont correctement restaurés si l'utilisateur appuie sur « Annuler ». Auparavant, il n'y avait aucune différence entre appuyer sur « OK » et « Annuler ». [https://github.com/FreeCAD/FreeCAD/pull/11188 Pull request #11188]
* La couleur et la transparence des faces peuvent désormais être définies par vue. [https://github.com/FreeCAD/FreeCAD/pull/11315 Pull request #11315]
* Le mode multisélection a été ajouté et peut être activé dans les préférences. Dans ce mode, plusieurs sommets, arêtes et faces peuvent être sélectionnés en cliquant dessus avec le bouton gauche de la souris, sans avoir à maintenir la touche Ctrl enfoncée. [https://github.com/FreeCAD/FreeCAD/pull/11417 Pull request #11417]
* [[TechDraw_ExtensionAreaAnnotation/fr|Surface]] peut maintenant calculer les surfaces de faces arbitraires. [https://github.com/FreeCAD/FreeCAD/pull/11473 Pull request #11473]
* Les lignes non continues suivront désormais les normes ISO/ANSI au lieu du style des lignes de Qt. Une nouvelle préférence a été ajoutée pour sélectionner la norme. [https://github.com/FreeCAD/FreeCAD/pull/11594 Pull request #11594]
* Le comportement de l'outil [[TechDraw_AxoLengthDimension/fr|Cote axonométrique]] a été amélioré. Désormais, lors de la cotation d'arêtes parallèles aux axes du système de coordonnées global, la valeur réelle (3D) est calculée automatiquement et insérée dans la propriété Format Spec (sous forme de texte). [https://github.com/FreeCAD/FreeCAD/pull/11678 Pull request #11678]
* L'outil [[TechDraw_ExtensionPositionSectionView/fr|Positionner une vue en coupe]] peut maintenant être utilisé en sélectionnant une arête dans une vue de coupe et un sommet dans la vue source. [https://github.com/FreeCAD/FreeCAD/pull/11797 Pull request #11797]
* Des améliorations mineures mais importantes ont été apportées à l'utilisation : un double-clic sur la page TechDraw permet désormais d'accéder à cet atelier et l'outil TechDraw Déplacer une vue a été remplacé par un simple glisser-déposer dans la [[Tree_view/fr|vue en arborescence]]. Les outils TechDraw Ajout vue dans une fenêtre de rognage et TechDraw Suppression vue d'une fenêtre de rognage ont également été remplacés par un simple glisser-déposer dans l'arborescence. [https://github.com/FreeCAD/FreeCAD/pull/13063 Pull request #13063]
* L'outil [[TechDraw_ProjectShape/fr|Projection de forme]] a été supprimé de TechDraw car il provenait de l'ancien atelier Drawing et n'avait rien à voir avec une page TechDraw. [https://github.com/FreeCAD/FreeCAD/pull/13655 Pull request #13655]
* L'outil [[TechDraw_View/fr|Vue]] a été amélioré afin qu'il puisse gérer plus de types d'objets et de paramètres. Cela a permis de supprimer les outils suivants de la barre d'outils : [[TechDraw_SpreadsheetView/fr|Vue d'un objet Spreadsheet]], [[TechDraw_ArchView/fr|Vue d'un objet Arch]], [[TechDraw_Symbol/fr|Symbole]], [[TechDraw_Image/fr|Image]] et [[TechDraw_ProjectionGroup/fr|Groupe de projections]]. [https://github.com/FreeCAD/FreeCAD/pull/13219 Pull request #13219]
* L'accrochage a été ajouté pour permettre l'alignement automatique des vues et des dimensions. [https://github.com/FreeCAD/FreeCAD/pull/13659 Pull request #13659]
* La gestion des cosmétiques a été améliorée de diverses manières. [https://github.com/FreeCAD/FreeCAD/pull/14216 Pull request #14216]
 h italiano (it)!!FUZZY!!* Le sezioni basate su altre sezioni ora utilizzano la forma originale (non tagliata) per impostazione predefinita. Questo può essere modificato nelle impostazioni della sezione per utilizzare invece la sezione precedente. [https://github.com/FreeCAD/FreeCAD/pull/10281 Pull request #10281]
* Gli oggetti cosmetici e le linee centrali ora possono essere eliminati selezionandoli e premendo il tasto Elimina. In precedenza, ciò comportava la cancellazione dell'intera vista. [https://github.com/FreeCAD/FreeCAD/pull/10695 Pull request #10695] e [https://github.com/FreeCAD/FreeCAD/pull/10813 Pull request #10813]
* È stata aggiunta una nuova icona più intuitiva per lo strumento [[TechDraw_WeldSymbol/it|Saldatura]]. [https://github.com/FreeCAD/FreeCAD/pull/10936 Pull request #10936]
* Il comportamento della modalità punto + bordo di [[TechDraw_LengthDimension/it|Quotatura Lunghezza]] è stato corretto. [https://github.com/FreeCAD/FreeCAD/pull/10860 Pull request #10860]
* È stato aggiunto un indicatore di selezione per il pulsante [[TechDraw_ToggleFrame|ToggleFrame]] in modo che un utente possa vedere se il pulsante è attivato o meno. [https://github.com/FreeCAD/FreeCAD/pull/11240 Pull request #11240]
* Il comportamento dello strumento [[TechDraw_DecorateLine/it|DecorateLine]] è stato migliorato. Ora facendo doppio clic su una riga si richiama questo strumento. E gli stili di linea vengono ripristinati correttamente se l'utente preme ''Annulla''. In precedenza non c'era differenza tra premere "OK" e "Annulla". [https://github.com/FreeCAD/FreeCAD/pull/11188 Pull request #11188]
* Ora è possibile impostare il colore e la trasparenza delle facce per la vista. [https://github.com/FreeCAD/FreeCAD/pull/11315 Pull request #11315]
* È stata aggiunta la modalità di selezione multipla che può essere abilitata nelle Preferenze. In questa modalità, è possibile selezionare più vertici, bordi e facce facendo clic con il tasto sinistro su di essi, senza dover tenere premuto il tasto Ctrl. [https://github.com/FreeCAD/FreeCAD/pull/11417 Pull request #11417]
* [[TechDraw_ExtensionAreaAnnotation/it|ExtensionAreaAnnotation]] ora può calcolare aree di facce arbitrarie. [https://github.com/FreeCAD/FreeCAD/pull/11473 Pull request #11473]
* Le linee non continue ora seguiranno gli standard ISO/ANSI anziché uno stile di linea Qt. È stata aggiunta una nuova preferenza per selezionare lo standard. [https://github.com/FreeCAD/FreeCAD/pull/11594 Pull request #11594]
* Il comportamento dello strumento [[TechDraw_AxoLengthDimension/it|AxoLengthDimension]] è stato migliorato. Ora, quando si quotano i bordi paralleli agli assi del sistema di coordinate globali, il valore effettivo (3D) viene calcolato automaticamente e inserito nella proprietà Format Spec (come testo). [https://github.com/FreeCAD/FreeCAD/pull/11678 Pull request #11678]
* Lo strumento [[TechDraw_ExtensionPositionSectionView/it|ExtensionPositionSectionView]] ora può essere utilizzato selezionando un bordo in una vista in sezione e un vertice nella vista di origine. [https://github.com/FreeCAD/FreeCAD/pull/11797 Pull request #11797]
 h polski (pl)* Przekroje oparte na innych przekrojach używają teraz domyślnie oryginalnego ''(nieprzyciętego)'' kształtu. Można to zmienić w ustawieniach przekroju, aby zamiast tego użyć poprzedniego przekroju. [https://github.com/FreeCAD/FreeCAD/pull/10281 Pull request #10281].
* Obiekty kosmetyczne i linie środka można teraz usuwać, zaznaczając je i naciskając klawisz {{Button|Delete}}. Wcześniej powodowało to usunięcie całego widoku. [https://github.com/FreeCAD/FreeCAD/pull/10695 Pull request #10695] oraz [https://github.com/FreeCAD/FreeCAD/pull/10813 Pull request #10813]
* Dodano nową, bardziej intuicyjną ikonę dla narzędzia [[TechDraw_WeldSymbol/pl|Symbol spawalniczy]]. [https://github.com/FreeCAD/FreeCAD/pull/10936 Pull request #10936]
* Poprawiono zachowanie trybu punkt + krawędź narzędzia [[TechDraw_LengthDimension/pl|Wstaw wymiar długości]]. [https://github.com/FreeCAD/FreeCAD/pull/10860 Pull request #10860]
* Dodano sprawdzanie stanu dla przycisku [[TechDraw_ToggleFrame/pl|Włącz / wyłącz wyświetlanie ramek]], aby użytkownik mógł zobaczyć, czy przycisk jest aktywny, czy nie. [https://github.com/FreeCAD/FreeCAD/pull/11240 Pull request #11240]
* Poprawiono zachowanie narzędzia [[TechDraw_DecorateLine/pl|Zmień wygląd linii]]. Teraz dwukrotne kliknięcie linii wywołuje to narzędzie. Style linii są poprawnie przywracane, jeśli użytkownik naciśnie przycisk ''Anuluj''. Wcześniej nie było różnicy między naciśnięciem przycisku ''OK'' i ''Anuluj''. [https://github.com/FreeCAD/FreeCAD/pull/11188 Pull request #11188].
* Kolor i przezroczystość ścian można teraz ustawić dla każdego widoku. [https://github.com/FreeCAD/FreeCAD/pull/11315 Pull request #11315]
* Dodano tryb wielokrotnego wyboru, który można włączyć w Preferencjach. W tym trybie można wybrać wiele wierzchołków, krawędzi i ścian, klikając je lewym przyciskiem myszy, bez konieczności trzymania wciśniętego klawisza Ctrl. [https://github.com/FreeCAD/FreeCAD/pull/11417 Pull request #11417]
* [[TechDraw_ExtensionAreaAnnotation|Rozszerzenie Oblicz obszar wybranych powierzchni]] może teraz obliczać obszary dowolnych powierzchni. [https://github.com/FreeCAD/FreeCAD/pull/11473 Pull request #11473]
* Linie nieciągłe będą teraz zgodne ze standardami ISO / ANSI zamiast stylu linii Qt. Dodano nową preferencję do wyboru standardu. [https://github.com/FreeCAD/FreeCAD/pull/11594 Pull request #11594]
* Poprawiono działanie narzędzia [[TechDraw_AxoLengthDimension/pl|Wstaw wymiar długości w aksonometrii]]. Teraz, podczas wymiarowania krawędzi równoległych do osi globalnego układu współrzędnych, rzeczywista wartość ''(3D)'' jest obliczana automatycznie i wstawiana do właściwości Format Spec ''(jako tekst)''. [https://github.com/FreeCAD/FreeCAD/pull/11678 Pull request #11678]
*Narzędzie [[TechDraw_ExtensionPositionSectionView/pl|Rozszerzenie Wyrównaj widok przekroju]] może być teraz używane poprzez wybranie krawędzi w widoku przekroju i wierzchołka w widoku źródłowym. [https://github.com/FreeCAD/FreeCAD/pull/11797 Pull request #11797]
* Wprowadzono małe, ale istotne usprawnienia użytkowe - podwójne kliknięcie na stronie środowiska Rysunek techniczny powoduje przejście do tego modułu a narzędzie ''Przesuń widok'' zostało zastąpione prostym przeciągnięciem i upuszczeniem w [[Tree_view/pl|drzewie]]. Narzędzia ''Dodaj widok do grupy wycinków'' i ''Usuń widok z grupy wycinków'' również zastąpiono przeciąganiem i upuszczaniem w drzewie. [https://github.com/FreeCAD/FreeCAD/pull/13063 Pull request #13063]
* Tabele szablonów rysunków są teraz automatycznie wypełniane dostępnymi informacjami ''(jak data i tytuł)''. [https://github.com/FreeCAD/FreeCAD/pull/13005 Pull request #13005]
* Narzędzie [[TechDraw_ProjectShape/pl|Rzutowanie kształtów]] zostało usunięte z środowiska Rysunek Techniczny, ponieważ zostało odziedziczone po starym środowisku roboczym Kreślenie i nie ma nic wspólnego ze stroną Rysunku technicznego. [https://github.com/FreeCAD/FreeCAD/pull/13655 Pull request #13655].
* Narzędzie [[TechDraw_View/pl|Wstaw widok]] zostało ulepszone, aby mogło obsługiwać więcej typów obiektów i ustawień. Pozwoliło to na usunięcie następujących narzędzi z paska narzędzi: [[TechDraw_SpreadsheetView/pl|Wstaw widok Arkusza kalkulacyjnego]], [[TechDraw_ArchView/pl|Wstaw obiekt środowiska Architektura]], [[TechDraw_Symbol/pl|Wstaw symbol SVG]], [[TechDraw_Image/pl|Wstaw obraz bitmapy]] i [[TechDraw_ProjectionGroup/pl|Wstaw grupę rzutów]]. [https://github.com/FreeCAD/FreeCAD/pull/13219 Pull request #13219]
* Dodano przyciąganie, aby umożliwić automatyczne wyrównanie widoków i wymiarów. [https://github.com/FreeCAD/FreeCAD/pull/13659 Pull request #13659]
* Poprawiono obsługę elementów linii pomocniczych ''(kosmetycznych)'' na różne sposoby. [https://github.com/FreeCAD/FreeCAD/pull/14216 Pull request #14216]