All translations

Enter a message name below to show all available translations.

Message

Found 8 translations.

NameCurrent message text
 h Deutsch (de)* Wir werden jetzt mit der gleichen Schnitt Methode Löcher für die Schrauben machen. Nachdem wir acht Löcher brauchen, zwei in jedem Fuß, könnten wir acht zu entfernende Objekte erzeugen. Stattdessen werden wir andere Wege beschreiten und vier Röhren erstellen, die für die Löcher in den Füßen wiederverwendet werden. Daher werden wir vier Röhren  mit dem  [[Image:Part_Cylinder.svg|16px]] '''Zylinder''' Werkzeug erstellen. Du kannst wieder nur eine erstellen und später wieder duplizieren. Gib jedem Zylinder einen Radius von 6 mm. Dieses Mal müssen wir sie drehen, was ebenfalls mit der '''Placement''' Eigenschaft unter dem Daten Reiter gemacht wird ''('''Anmerkung''': ändere die Axis Eigenschaft ''vor'' dem Setzen des Winkels oder die Drehung wird nicht durchgeführt)'':
** cylinder: height: 130cm, angle: 90°, axis: x:0,y:1,t:0 position: x:-10mm, y:40mm, z:72cm
** cylinder001: height: 130cm, angle: 90°, axis: x:0,y:1,z:0 position: x:-10mm, y:84cm, z:72cm
** cylinder002: height: 90cm, angle: 90°, axis: x:-1,y:0,z:0 position: x:40mm, y:-10mm, z:70cm
** cylinder003: height: 90cm, angle: 90°, axis: x:-1,y:0,z:0 position: x:124cm, y:-10mm, z:70cm
 h English (en)* We will now make holes for the screws, using the same Cut method. Since we need 8 holes, two in each foot, we could make 8 objects to be subtracted. Instead, let's explore other ways and make 4 tubes, that will be reused by two of the feet. So let's create four tubes by using the [[Image:Part_Cylinder.svg|16px]] '''Cylinder''' tool. You can again, make only one and duplicate it afterwards. Give all cylinders a radius of 6mm. This time, we will need to rotate them, which is also done via the '''Placement''' property under the Data tab ''('''Note:''' change the Axis property ''before'' setting the Angle, or the rotation will not be applied)'':
** Cylinder: height: 130cm, angle: 90°, axis: x:0,y:1,z:0, position: x:-10mm, y:40mm, z:72cm
** Cylinder001: height: 130cm, angle: 90°, axis: x:0,y:1,z:0, position: x:-10mm, y:84cm, z:72cm
** Cylinder002: height: 90cm, angle: 90°, axis: x:-1,y:0,z:0, position: x:40mm, y:-10mm, z:70cm
** Cylinder003: height: 90cm, angle: 90°, axis: x:-1,y:0,z:0, position: x:124cm, y:-10mm, z:70cm
 h français (fr)* Nous allons maintenant faire des trous pour les vis en utilisant la même méthode de coupe. Puisque nous avons besoin de 8 trous, deux dans chaque pied, nous pourrions faire 8 objets à soustraire. Au lieu de cela, voici une autre manière: créons quatre cylindres en utilisant l'outil [[Image:Part_Cylinder.svg|16px]] '''Cylindre''' (un cylindre pour deux pieds). Vous pouvez à nouveau en faire un seul et le copier ensuite. Donnez à tous les cylindres un rayon de 6 mm. Cette fois, nous devrons les faire pivoter, ce qui se fait également par la propriété '''Placement''' de l'onglet Données ''('''Note:''' changez la propriété de l'Axe ''avant'' de modifier la valeur de l'angle ou la rotation ne sera pas appliqué)''
** Cylindre : hauteur : 130cm, angle : 90°, axe: x : 0, y : 1, position : x : -10mm, y : 40mm, z : 72cm
** Cylindre001 : hauteur : 130cm, angle : 90°, axe : x : 0, y : 1, position : x : -10mm, y : 84cm, z : 72cm
** Cylindre002 : hauteur : 90cm, angle : 90°, axe : x : -1, y : 0, position : x : 40mm, y : -10mm, z : 70cm
** Cylindre003 : hauteur : 90cm, angle : 90°, axe : x : -1, y : 0, position : x: 124cm, y : -10mm, z : 70cm
 h italiano (it)* Ora faremo i fori per le viti, utilizzando lo stesso metodo di Taglio. Dato che servono 8 fori, due in ogni gamba, potremmo fare 8 oggetti da sottrarre. Invece, esploriamo altri modi e facciamo 4 tubi, che saranno riutilizzati da due delle gambe. Quindi creare quattro tubi utilizzando lo strumento [[Image:Part_Cylinder.svg|16px]] '''Cilindro'''. È nuovamente possibile farne un solo e poi duplicarlo. Dare a tutti i cilindri un raggio di 6 mm. Questa volta, avremo bisogno di ruotarli, che avviene anche attraverso la proprietà '''Placement''' nella scheda Dati '' ('''Nota:''' cambiare la proprietà dell'Asse ''prima'' di impostare l'angolo, altrimenti la rotazione non viene applicata) '':
** Cylinder: height: 130 cm, angle: 90°, axis: x:0,y:1,z:0, position: x:-10 mm, y:40 mm, z:72 cm
** Cylinder001: height: 130 cm, angle: 90°, axis: x:0,y:1,z:0, position: x:-10 mm, y:84 cm, z:72 cm
** Cylinder002: height: 90 cm, angle: 90°, axis: x:-1,y:0,z:0, position: x:40 mm, y:-10 mm, z:70 cm
** Cylinder003: height: 90cm, angle: 90°, axis: x:-1,y:0,z:0, position: x:124 cm, y:-10 mm, z:70 cm
 h polski (pl)* Teraz wykonamy otwory na śruby, używając tej samej metody cięcia. Ponieważ potrzebujemy 8 otworów, po dwa w każdej stopie, moglibyśmy wykonać 8 obiektów do odjęcia. Zamiast tego zbadajmy inne sposoby i stwórzmy 4 rurki, które zostaną ponownie wykorzystane przez dwie stopy. Utwórzmy więc cztery rurki za pomocą narzędzia [[Image:Part_Cylinder.svg|16px]] '''Walec'''. Możesz ponownie utworzyć tylko jeden i powielić go później. Nadaj wszystkim cylindrom promień 6 mm. Tym razem będziemy musieli je obrócić, co również odbywa się za pomocą właściwości '''Umieszczenie''' w zakładce Dane ''(''Uwaga:''' zmień właściwość Oś ''przed'' ustawieniem Kąta, w przeciwnym razie obrót nie zostanie zastosowany)'':
** Cylinder: wysokość: 130cm, kąt: 90°, oś: x:0,y:1,z:0, pozycja: x:-10mm, y:40mm, z:72cm
** Cylinder001: wysokość: 130cm, kąt: 90°, oś: x:0,y:1,z:0, pozycja: x:-10mm, y:84cm, z:72cm
** Cylinder002: wysokość: 90cm, kąt: 90°, oś: x:-1,y:0,z:0, pozycja: x:40mm, y:-10mm, z:70cm
** Cylinder003: wysokość: 90cm, kąt: 90°, oś: x:-1,y:0,z:0, pozycja: x:124cm, y:-10mm, z:70cm
 h română (ro)* Vom face acum găuri pentru șuruburi, folosind aceeași metodă Cut. Deoarece avem nevoie de 8 găuri, câte două în fiecare picior, putem face ca 8 obiecte să fie scăzute. În schimb, să explorăm alte căi și să facem 4 tuburi, care vor fi refolosite de două picioare. Deci, sa creem tuburi folosind cilindri [[Image:Part_Cylinder.png|16px]] '''Cylinder''' tool. Din nou, puteți face una și o duplicați ulterior. Dați tuturor cilindrilor o rază de 6 mm. De data aceasta, va trebui să le rotim, ceea ce se face și prin '''Placement''' property under the Data tab ''('''Note:''' change the Axis property ''before'' setting the Angle, or the rotation will not be applied)'':
** Cylinder: height: 130cm, angle: 90°, axis: x:0,y:1, position: x:-10mm, y:40mm, z:72cm
** Cylinder001: height: 130cm, angle: 90°, axis: x:0,y:1, position: x:-10mm, y:84cm, z:72cm
** Cylinder002: height: 90cm, angle: 90°, axis: x:-1,y:0, position: x:40mm, y:-10mm, z:70cm
** Cylinder003: height: 90cm, angle: 90°, axis: x:-1,y:0, position: x:124cm, y:-10mm, z:70cm
 h русский (ru)* Теперь сделаем отверстия для винтов, используя тот же метод Cut. Поскольку нам нужно 8 отверстий, два на каждую ножку, нам нужно сделать 8 вычитаемых объектов. Вместо этого поищем другой путь и сделаем 4 трубки, которые могут использоваться двумя ножками. Создадим четыре трубки инструментом [[Image:Part_Cylinder.svg|16px]] '''Цилиндр'''. Можно опять сделать только один и дублировать взамен. Возьмём все цилиндры радиусом 6mm. Теперь нам надо повернуть их, что так же делается параметром '''Placement''' на вкладке Данные ''('''Примечание:''' измените свойство параметра Axis ''перед'' установкой Angle, или поворот не будет применён)'':
** Цилиндр: height: 130cm, angle: 90°, axis: x:0,y:1, position: x:-10mm, y:40mm, z:72cm
** Цилиндр001: height: 130cm, angle: 90°, axis: x:0,y:1, position: x:-10mm, y:84cm, z:72cm
** Цилиндр002: height: 90cm, angle: 90°, axis: x:-1,y:0, position: x:40mm, y:-10mm, z:70cm
** Цилиндр003: height: 90cm, angle: 90°, axis: x:-1,y:0, position: x:124cm, y:-10mm, z:70cm
 h 中文(中国大陆) (zh-cn)* 现在我们将使用相同的 Cut 方法为螺钉制作孔。由于我们需要 8 个孔,每个桌脚需要两个,我们可以制作 8 个要减去的对象。相反,让我们探索其他方法,并制作 4 个管道,这些管道将由两个脚重复使用。因此,让我们使用 [[Image:Part_Cylinder.svg|16px]] '''圆柱体''' 工具创建四个管道。您可以再次只制作一个圆柱体,然后将其复制。给所有圆柱体一个半径为 6 毫米。这次,我们需要旋转它们,这也是通过数据选项卡下的 '''放置''' 属性完成的 ''('''注意:''' 在设置角度之前更改轴属性,否则旋转将不会应用)'':
** Cylinder:高度:130cm,角度:90°,轴:x:0,y:1,z:0,位置:x:-10mm,y:40mm,z:72cm
** Cylinder001:高度:130cm,角度:90°,轴:x:0,y:1,z:0,位置:x:-10mm,y:84cm,z:72cm
** Cylinder002:高度:90cm,角度:90°,轴:x:-1,y:0,z:0,位置:x:40mm,y:-10mm,z:70cm
** Cylinder003:高度:90cm,角度:90°,轴:x:-1,y:0,z:0,位置:x:124cm,y:-10mm,z:70cm