FCGear: Corona dentata

From FreeCAD Documentation
Revision as of 15:18, 25 May 2024 by Simone.b (talk | contribs) (Created page with "La ruota dentata ricorda una cremagliera curva a forma di anello. L'angolo di pressione diminuisce continuamente dal diametro esterno a quello interno. In questo modo la velocità periferica variabile della corona dentata viene compensata con la velocità periferica costante del pignone. I denti esterni appuntiti e i fianchi ripidi del dente sul diametro interno limitano la larghezza utile del dente. Gli ingranaggi a corona raggiungono efficienze simili agli ingranaggi c...")
Other languages:

Corona dentata

Posizione nel menu
Gear → Crown Gear
Ambiente
FCGear
Avvio veloce
None
Introdotto nella versione
v0.16
Vedere anche
Ingranaggio ad evolvente

Descrizione

La ruota dentata ricorda una cremagliera curva a forma di anello. L'angolo di pressione diminuisce continuamente dal diametro esterno a quello interno. In questo modo la velocità periferica variabile della corona dentata viene compensata con la velocità periferica costante del pignone. I denti esterni appuntiti e i fianchi ripidi del dente sul diametro interno limitano la larghezza utile del dente. Gli ingranaggi a corona raggiungono efficienze simili agli ingranaggi cilindrici. Una corona dentata può azionare più pignoni.

Campi di applicazione noti per le corone dentate:

  • Azionamenti dell'asse posteriore per auto e moto
  • Meccanismo girevole per tavoli operatori
  • Teste per fresatura angolare
  • Sistemi di utensili motorizzati con pignoni multipli e corona dentata

Sopra: corona dentata

Utilizzo

  1. Switch to the FCGear Workbench.
  2. There are several ways to invoke the command:
    • Press the Crown Gear button in the toolbar.
    • Select the Gear → Crown Gear option from the menu.
  3. The crown gear is displayed without teeth by default. (introduced in version 0.21)
  4. Change the gear parameters to the required conditions (see Properties).
  5. Set the Datipreview_mode property to false to display the teeth (see Notes).

Proprietà

Un oggetto FCGear CrownGear deriva da un oggetto Part Feature e ne eredita tutte le proprietà. Ha inoltre le seguenti proprietà aggiuntive:

Dati

accuracy

  • Datinum_profiles (Integer): Default is 4. Number of profiles used for loft.
  • Datipreview_mode (Bool): Default is true.

base

  • Datiheight (Length): Default is 2 mm. Value for the tooth width.
  • Datimodule (Length): Default is 1 mm. Module is the ratio of the reference diameter of the gear divided by the number of teeth (see Notes).
  • Datiother_teeth (Integer): Default is 15. Number of teeth of the construction gear (pinion) (see Notes).
  • Datiteeth (Integer): Default is 15. Number of teeth.
  • Datithickness (Length): Default is 5 mm. Height from the tip of tooth to the lower side of the crown wheel.

involute

  • Datipressure_angle (Angle): Default is 20 ° (see Notes).

version

  • Dativersion (String):

Note

  • The Datipreview_mode property is set to true by default and when the gear is created you'll find this message in the report view:
    Gear module: Crown gear created, preview_mode = true for improved performance. Set preview_mode property to false when ready to cut teeth.
  • module: Using ISO (International Organization for Standardization) guidelines, Module size is designated as the unit representing gear tooth-sizes. Module (m): m = 1 (p = 3.1416), m = 2 (p = 6.2832), m = 4 (p = 12.566). If you multiply Module by Pi, you can obtain Pitch (p). Pitch is the distance between corresponding points on adjacent teeth.
  • other_teeth: Several pinions with the same number of teeth only can be used on one crown wheel.
  • pressure_parameter: Only change the parameter, if sufficient knowledge of the gear geometry is available.
  • The geometry of the crown gear is primarily determined by the spur pinion geometry (other_teeth).
  • Create spur gear with Involute gear. The number of teeth must be identical to the parameter other_teeth of the crown gear.
  • Adjustments for optimal running characteristics can be made with the parameters of involute gear.

Panoramica dell'insieme corona e ingranaggio cilindrico

  • (1) Spur gear
  • (2) Crown gear
  • (3) Tooth width
  • (4) Inner diameter
  • (5) Outer diameter

Formule utili

  • Inner diameter (4)
    • inner diamter = module (spur gear) * teeth (crown gear) * cos pressure_paramter (pinion) : cos pressure_parameter (crown gear)
  • Outer diameter (5)
    • outer diamter = inner diameter + 2x height (tooth width crown gear)