PartDesign Pad
|
Menu location |
---|
Part Design → Create an additive feature → Pad |
Workbenches |
PartDesign |
Default shortcut |
None |
Introduced in version |
- |
See also |
PartDesign Pocket |
Description
The Pad tool extrudes a sketch or a face of a solid along a straight path.
Sketch (A) shown on the left; end result after pad operation (B) on the right.
Usage
- Select one sketch or face to be padded. introduced in version 0.20: Alternatively you can select several sketches or faces.
- Press the
Pad button.
- Set the Pad parameters, see the Options below.
- Click OK.
When selecting a single sketch, it can have multiple enclosed profiles inside a larger one, for example a rectangle with two circles inside it. But the profiles may not intersect each other. introduced in version 0.20
Options
When creating a pad, the Pad parameters dialog will be shown. It offers the following settings:
Type
Type offers five different ways of specifying the length to which the pad will be extruded:
Dimension
Enter a numeric value for the length of the pad. The default direction for extrusion is away (outside of) the support, but it can be changed by ticking the Reversed option. Extrusions occur by default normal to the defining sketch plane. This can be changed by specifying another Direction. With the option Symmetric to plane the pad will extend half of the given length to either side of the plane. Negative dimensions are not possible. Use the Reversed option instead.
To last
The pad will extrude up to the last face of the support in the extrusion direction. If there is no support, an error message will appear.
To first
The pad will extrude up to the first face of the support in the extrusion direction. If there is no support, an error message will appear.
Up to face
The pad will extrude up to a face in the model that can be chosen by clicking on it.
Two dimensions
This allows to enter a second length in which the pad should extend in the opposite direction (into the support). The directions can be switched by ticking the Reversed option.
Length
Defines the length of the pad. Multiple units can be used independently of the user's units preferences (m, cm, mm, nm, ft or ', in or "). This option is only available when Type is either Dimension or Two dimensions.
Offset to face
Offset from face at which the pad will end. This option is only available when Type is either To last, To first or Up to face.
Direction
Direction/edge
You can select the direction of the extrusion:
- Sketch normal: The sketch or face is extruded along its normal. If you have selected several sketches or faces to be extruded, the normal of the first one will be used. introduced in version 0.20
- Select reference...: The sketch is extruded along an edge of the 3D model. When this is method selected, you can click on any edge in the 3D model and it becomes the direction vector for the extrusion. introduced in version 0.20
- Custom direction: The sketch is extruded along a direction that can be specified via vector values.
Show direction
If checked, the pad direction will be shown. In case the pad uses a Custom direction, it can be changed. introduced in version 0.20
Length along sketch normal
If checked, the pad length is measured along the sketch normal, otherwise along the custom direction. introduced in version 0.20
Symmetric to plane
Tick the checkbox to extrude half of the given length to either side of the sketch or plane.
Reversed
Reverses the direction of the pad.
Taper angle
Tapers the pad in the extrusion direction by the given angle. A positive angle means the outer pad border gets wider. This option is only available if Type is either Dimension or Two dimensions. Note that inner structures receive the opposite taper angle. This is done to facilitate the design of molds and molded parts.
Limitations:
- Sketches containing B-Splines often cannot be properly tapered. This is a limitation of the OpenCASCADE kernel that FreeCAD uses.
- For larger angles tapering will fail if the end face of the pad would have fewer edges than the start face/sketch.
2nd length
Defines the length of the pad in the opposite extrusion direction. Multiple units can be used independently of the user's units preferences (m, cm, mm, nm, ft or ', in or "). This option is only available if Type is Two dimensions.
2nd taper angle
Tapers the pad in the opposite extrusion direction by the given angle. A positive angle means the outer pad border gets wider. This option is only available if Type is Two dimensions. Note that inner structures receive the opposite taper angle. This is done to facilitate the design of molds and molded parts.
Properties
- DataType: Type of ways how the pad will be extruded, see Options.
- DataLength: Defines the length of the pad, see Options.
- DataLength2: Second pad length in case the DataType is TwoLengths, see Options.
- DataUse Custom Vector: If checked, the pad direction will not be the normal vector of the sketch but the given vector, see Options.
- DataDirection: Vector of the pad direction if DataUse Custom Vector is used.
- DataAlong Sketch Normal: If true, the pad length is measured along the sketch normal. Otherwise and if DataUse Custom Vector is used, it is measured along the custom direction. introduced in version 0.20
- DataUp To Face: A face the pad will extrude up to, see Options.
- DataOffset: Offset from face in which the pad will end. This is only taken into account if the DataType option UpToLast, UpToFirst or UpToFace is used.
- DataRefine: True or false. Cleans up residual edges left after the operation. This property is initially set according to the user's settings (found in Preferences → Part design → General → Model settings). It can be manually changed afterwards. This property will be saved with the FreeCAD document.
Limitations
- Like all Part Design features, Pad creates a solid, thus the sketch must include a closed profile or it will fail with a Failed to validate broken face error.
- The algorithm used for To First and To Last is:
- Create a line through the center of gravity of the sketch
- Find all faces of the support cut by this line
- Choose the face where the intersection point is nearest/furthest from the sketch
- This means that the face that is found might not always be what you expected. If you run into this problem, use the Up to face type instead, and pick the face you want.
- For the very special case of extrusion to a concave surface, where the sketch is larger than this surface, extrusion will fail. This is a unresolved bug.
- Structure tools: Part, Group
- Helper tools: Create body, Create sketch, Edit sketch, Map sketch to face
- Modeling tools
- Datum tools: Create a datum point, Create a datum line, Create a datum plane, Create a local coordinate system, Create a shape binder, Create a sub-object(s) shape binder, Create a clone
- Additive tools: Pad, Revolution, Additive loft, Additive pipe, Additive helix, Additive box, Additive cylinder, Additive sphere, Additive cone, Additive ellipsoid, Additive torus, Additive prism, Additive wedge
- Subtractive tools: Pocket, Hole, Groove, Subtractive loft, Subtractive pipe, Subtractive helix, Subtractive box, Subtractive cylinder, Subtractive sphere, Subtractive cone, Subtractive ellipsoid, Subtractive torus, Subtractive prism, Subtractive wedge
- Transformation tools: Mirrored, Linear Pattern, Polar Pattern, Create MultiTransform, Scaled
- Dress-up tools: Fillet, Chamfer, Draft, Thickness
- Boolean: Boolean operation
- Extras: Migrate, Sprocket, Involute gear, Shaft design wizard
- Context menu: Set tip, Move object to other body, Move object after other object, Appearance, Set colors

- Getting started
- Installation: Download, Windows, Linux, Mac, Additional components, Docker, AppImage, Ubuntu Snap
- Basics: About FreeCAD, Interface, Mouse navigation, Selection methods, Object name, Preferences, Workbenches, Document structure, Properties, Help FreeCAD, Donate
- Help: Tutorials, Video tutorials
- Workbenches: Std Base, Arch, Draft, FEM, Inspection, Mesh, OpenSCAD, Part, PartDesign, Path, Points, Reverse Engineering, Robot, Sketcher, Spreadsheet, Start, Surface, TechDraw, Test Framework, Web
- Hubs: User hub, Power users hub, Developer hub