Jump to content

FCGear WormGear

From FreeCAD Documentation

FCGear WormGear

Menu location
Gear → Worm Gear
Workbenches
Gear
Default shortcut
None
Introduced in version
v0.16
See also
PartDesign InvoluteGear

Description[edit | edit source]

The FCGear WormGear command creates a worm gear. By default this is a single thread worm with one start that can also be transformed into a double or multiple thread worm with two or several starts respectively.

The worm can be considered a special case of a helical gear. Imagine that there is only one tooth on a spur gear. Now increase the helix angle so much that the tooth winds around the spur gear several times before it emerges on the opposite side. The result would be a single thread worm.

For a single-start worm, each full turn (360 degrees) of the worm advances the gear by one tooth. So a gear with 24 teeth will provide a gear reduction of 24:1. For a multi-start worm, the gear reduction equals the number of teeth on the gear, divided by the number of starts on the worm.

A worm can only be used with a worm wheel. This is called a worm drive. Like other gear arrangements, a worm drive can reduce rotational speed or transmit higher torque. One of the major advantages of worm gear drive units are that they can transfer motion in 90 degrees. A worm drive is also self-locking.

Worm gear (No. of teeth 3)

Usage[edit | edit source]

  1. Switch to the Gear Workbench.
  2. There are several ways to invoke the command:
    • Press the Worm Gear button in the toolbar.
    • Select the Gear → Worm Gear option from the menu.
  3. Change the gear parameter to the required conditions (see Properties).

Properties[edit | edit source]

See also: Property View.

An FCGear WormGear object is derived from a Part Feature object and inherits all its properties. It also has the following additional properties:

Data[edit | edit source]

base

  • Datadiameter (Length): Default is 5 mm. Pitch diameter.
  • Dataheight (Length): Default is 5 mm. Value of the worm length.
  • Datamodule (Length): Default is 1 mm. Module is the ratio of the reference diameter of the gear divided by the number of teeth (see Notes).
  • Datanum_teeth (Integer): Default is 3. Number of teeth (see Notes).
  • Datareverse_pitch (Bool): Default is false, true changes the rotating direction from right to left.

computed

involute

  • Datapressure_angle (Angle): Default is 20° (see Notes).

tolerance

  • Dataclearance (Float): Default is 0.25 (see Notes).
  • Datahead (Float): Default is 0. This value is used to change the tooth height.

version

  • Dataversion (String):

Notes[edit | edit source]

  • Databeta (β): If the lead angle is less than 5°, it is a self-locking gear. A typical example are the tuning pegs on a guitar or ukulele.
  • Dataclearance (c): At a worm gearing, clearance is the distance between the tooth tip of the worm and the tooth root of the worm wheel.
  • Datamodule (m): Using ISO (International Organization for Standardization) guidelines, Module size is designated as the unit representing gear tooth-sizes.
    • The module multiplied by the number of teeth (z) defines the pitch circle diameter (d): d=mz
    • The module multiplied by Pi (π) defines the pitch (p), the arc distance on the pitch circle between corresponding points of adjacent teeth: p=mπ
  • Datanum_teeth (number of teeth, z): The number of teeth in a worm is called the number of threads. Correspondingly, one speaks of single, double or multiple thread worms. In general, mainly single worms are produced, but in special cases the number of starts can be up to four (sometimes also more). If the number of teeth is changed, Databeta also changes.
  • Datapressure_angle: Only change the parameter, if sufficient knowledge of the gear geometry is available.

Useful formulas[edit | edit source]

Basic formulas common to standard worm gears
Symbol Term Formula FCGear Parameter
m Module - module
z Number of Teeth - num_teeth
p Pitch p=mπ -
β Lead Angle β=arctan(mzd)
or
β=arctan(padπ)
beta
d Pitch Diameter d=mztan(β) diameter
pa Axial Pitch pa=pz=mπz -
  • Axial pitch AKA lead
  • Lead angle AKA helix angle
  • Number of teeth AKA number of Threads

Worm wheel[edit | edit source]

The worm wheel must be designed manually. For this purpose FCGear InvoluteGear can be used for a simple construction. In any case, in-depth knowledge of the gear types is required.

Worm with worm wheel

Scripting[edit | edit source]

Use the power of Python to automate your gear modeling:

import FreeCAD as App
import FreeCADGui as Gui
import freecad.gears.commands
gear = freecad.gears.commands.CreateWormGear.create()
gear.num_teeth = 2
gear.diameter = 10
gear.height = 20
App.ActiveDocument.recompute()
Gui.SendMsgToActiveView("ViewFit")