Arch: Armătură dreaptă

From FreeCAD Documentation
(Redirected from Arch Rebar Straight/ro)
This page is a translated version of the page Reinforcement StraightRebar and the translation is 11% complete.
Outdated translations are marked like this.

Arch Rebar UShape

poziția meniului
Arch → Rebar tools
Ateliere
Arch
scurtătură
None
Prezentat în versiune
-
A se vedea, de asemenea,
LShape Rebar

Description

Descriere

Instrumentul Straight Rebarpoate permite utilizatorului să creeze o bară de armare dreaptă în elementul structural.

This tool is part of the Reinforcement Workbench, an external workbench that can be installed with the Addon Manager.

Cum se folosește

  1. Creați un element Structura structură
  2. Selectați orice față a structurii
  3. Apoi selectați Șipcă drept din uneltele pentru bare
  4. Un panou de activități va apărea în partea stângă a ecranului, după cum se arată mai jos
  5. Selectați orientarea dorită
  6. Dați intrările ca și capacul frontal, capacul lateral din dreapta, capacul lateral din stânga, capacul inferior și diametrul barei
  7. Selectați modul de distribuire fie cantitate, fie spațiere
  8. Dacă spațiul este selectat, un utilizator poate de asemenea să opteze pentru spacing custom
  9. Selectează fața selectată este utilizată pentru a verifica sau schimba fața pentru distribuția barei
  10. Faceți clic pe OK sau pe Apply pentru a genera barele de armare
  11. Faceți clic pe Cancel pentru a ieși din panoul de activități

Task panel for the tool

Proprietăți

  • DateOrientation: Acesta decide orientarea armăturii (de ex. jos, sus, drepta și stânga).
  • DateFront Cover: Distanța dintre armături și fațetele selectate.
  • DateRight Cover: Distanța între capătul dintre capătul dreapta al armăturii și fațeta dreapta a structurii.
  • DateLeft Cover: Distanța dintre capătul din stânga al armăturii și fațeta stângă a structurii
  • DateBottom Cover: Distanța dintre armătură și fațeta de jos a structurii.
  • DateTop Cover: Distanța dintre armătură și fața superioară a structurii.
  • DateRounding: O valoare de rotunjire care trebuie aplicată colțurilor barelor, exprimată în raport cu diametrul acestora.
  • DateAmount: Cantitatea de armătură
  • DateSpacing: Distnța dintre acele fiecărei bare.

Scripting

Scrip-Programare

Instrumentul Straight Rebar poate fi utilizat în macros și de la consola Python prin utilizarea următoarei funcții:

Rebar = makeStraightRebar(f_cover, coverAlong, rt_cover, lb_cover,
                          diameter, amount_spacing_check, amount_spacing_value, orientation="Horizontal",
                          structure=None, facename=None)
  • Creates a Rebar object from the given structure, which is an Arch Structure, and facename, which is a face of that structure.
    • If no structure nor facename are given, it will take the user selected face as input.
  • f_cover, coverAlong, rt_cover, and lb_cover are inner offset distances for the rebar elements with respect to the faces of the structure.
    • f_cover is the frontal cover offset.
    • coverAlong is a tuple (position, value) that defines the offset value in one position (top, bottom, left, right) depending on the orientation.
    • rt_cover is either the right or the top cover offset, depending on the value of coverAlong and orientation.
    • lb_cover is either the left or the bottom cover offset, depending on the value of coverAlong and orientation.
  • diameter is the diameter of the reinforcement bars inside the structure.
  • amount_spacing_check if it is True it will create as many reinforcement bars as given by amount_spacing_value; if it is False it will create reinforcement bars separated by the numerical value of amount_spacing_value.
  • amount_spacing_value specifies the number of reinforcement bars, or the value of the separation between them, depending on amount_spacing_check.
  • orientation specifies the orientation of the rebar; it can be "Horizontal" or "Vertical".

Depending on the orientation of the rebar, the function can be called in two general ways by setting coverAlong appropriately.

The rebar is horizontal

Rebar = makeStraightRebar(f_cover, ("Top Side", value), right_cover, left_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Bottom Side", value), right_cover, left_cover, ...)
  • coverAlong is a tuple with either a "Top Side" or a "Bottom Side" offset value.
  • In this case rt_cover refers to the right_cover offset, and lb_cover refers to the left_cover offset.

The rebar is vertical

Rebar = makeStraightRebar(f_cover, ("Left Side", value), top_cover, bottom_cover, ...)
Rebar = makeStraightRebar(f_cover, ("Right Side", value), top_cover, bottom_cover, ...)
  • coverAlong is a tuple with either a "Left Side" or a "Right Side" offset value.
  • In this case rt_cover refers to the top_cover offset, and lb_cover refers to the bottom_cover offset.

Example horizontal

import Arch, Draft, StraightRebar

Structure = Arch.makeStructure(length=1000, width=1000, height=400)
Structure.ViewObject.Transparency = 80
FreeCAD.ActiveDocument.recompute()

Rebar = StraightRebar.makeStraightRebar(50, ("Bottom Side", 20), 100, 100,
                                        12, True, 5, "Horizontal", Structure, "Face4")
Rebar.ViewObject.ShapeColor = (0.9, 0.0, 0.0)

Rebar2 = StraightRebar.makeStraightRebar(50, ("Bottom Side", 50), 100, 100,
                                         12, True, 5, "Horizontal", Structure, "Face6")
Rebar2.ViewObject.ShapeColor = (0.0, 0.0, 0.9)

Example vertical

import Arch, Draft, StraightRebar

Structure2 = Arch.makeStructure(length=1000, width=1000, height=400)
Structure2.ViewObject.Transparency = 80
Draft.move(Structure2, FreeCAD.Vector(1500, 0, 0))
FreeCAD.ActiveDocument.recompute()

Rebar3 = StraightRebar.makeStraightRebar(50, ("Left Side", 20), 100, 100,
                                         12, True, 5, "Vertical", Structure2, "Face4")
Rebar3.ViewObject.ShapeColor = (0.9, 0.5, 0.0)

Rebar4 = StraightRebar.makeStraightRebar(50, ("Left Side", 50), 100, 100,
                                         12, True, 5, "Vertical", Structure2, "Face6")
Rebar4.ViewObject.ShapeColor = (0.0, 0.5, 0.5)

Edition of rebar

Schimbarea proprietăților armăturii tip bară dreaptă.

editStraightRebar(Rebar, f_cover, coverAlong, rt_cover, lb_cover,
                  diameter, amount_spacing_check, amount_spacing_value, orientation,
                  structure=None, facename=None)
  • Rebar is a previously created StraightRebar object.
  • The other parameters are the same as required by the makeStraightRebar() function.
  • structure and facename may be omitted so that the rebar stays in the original structure.

Example:

import StraightRebar

StraightRebar.editStraightRebar(Rebar, 50, ("Top Side", 20), 100, 100,
                                24, True, 7, "Horizontal")

StraightRebar.editStraightRebar(Rebar2, 50, ("Top Side", 50), 100, 100,
                                24, True, 7, "Horizontal")

StraightRebar.editStraightRebar(Rebar3, 50, ("Right Side", 20), 100, 100,
                                24, True, 7, "Vertical")

StraightRebar.editStraightRebar(Rebar4, 50, ("Right Side", 50), 100, 100,
                                24, True, 7, "Vertical")