Tutorials/ko: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 82: Line 82:


<gallery mode=packed heights=200px style="font-size:1.1em">
<gallery mode=packed heights=200px style="font-size:1.1em">
FEM example01 pic00.jpg|link=[[FEM CalculiX Cantilever 3D]]|[[FEM CalculiX Cantilever 3D|CalculiX cantilever FEM analysis]] (v0.17) <br/>This in an example included in every installation of FreeCAD; it demonstrates a basic analysis with the CalculiX FE solver. Purge the current result, re-run the solver, and view the displacements and stresses in the deformed mesh in the viewport.
FEM example01 pic00.jpg|link=[[FEM CalculiX Cantilever 3D]]|[[FEM CalculiX Cantilever 3D|CalculiX cantilever FEM analysis]] (v0.20) <br/>This in an example included in every installation of FreeCAD; it demonstrates a basic analysis with the CalculiX FE solver. Purge the current result, re-run the solver, and view the displacements and stresses in the deformed mesh in the viewport.


FEM tutorial result.png|link=[[FEM tutorial]]|[[FEM tutorial|Simple FEM introduction]] (v0.17) <br/>This is a short introduction to the steps required to perform an analysis in the FEM Workbench: model your object, create a mesh, add constraints and forces, add a material, run the solver, and visualize the results.
FEM tutorial result.png|link=[[FEM tutorial]]|[[FEM tutorial|Simple FEM introduction]] (v0.20) <br/>This is a short introduction to the steps required to perform an analysis in the FEM Workbench: model your object, create a mesh, add constraints and forces, add a material, run the solver, and visualize the results.


Figure 11 Deformed Mesh.png|link=[[FEM Shear of a Composite Block]]|[[FEM Shear of a Composite Block|FEM shear analysis of a composite block]] (v0.17) <br/>Study the deformation of a block made of a hard nucleus surrounded by a softer material: create mesh regions, add materials, set up sliding constraints, add shear loads, run the solver, and visualize the results with a clip plane.
Figure 11 Deformed Mesh.png|link=[[FEM Shear of a Composite Block]]|[[FEM Shear of a Composite Block|FEM shear analysis of a composite block]] (v0.17) <br/>Study the deformation of a block made of a hard nucleus surrounded by a softer material: create mesh regions, add materials, set up sliding constraints, add shear loads, run the solver, and visualize the results with a clip plane.
Line 177: Line 177:
|
|
|
|

|-
| [[Adding_a_new_mouse_navigation_option_to_FreeCAD|Adding a new mouse navigation option to FreeCAD (unfinished)]]
| Programming
| Advanced
|
| [[User:Kunda1|Kunda1]]
| 0.19.x
| None

|-
| [[Advanced_Attachment_OYX|Advanced Attachment OYX]]
| Attachment
| Intermediate/Advanced
|
| [[User:drmacro|drmacro]]
| 0.19
| None

|-
| [[Advanced_TechDraw_Tutorial|Advanced TechDraw Tutorial (unfinished)]]
| TechDraw Workbench
| Advanced
|
| [[User:domad|domad]]
| 0.19
| None


|-
|-
Line 189: Line 216:
|-
|-
| [[Analysis_of_reinforced_concrete_with_FEM|Analysis of reinforced concrete with FEM]]
| [[Analysis_of_reinforced_concrete_with_FEM|Analysis of reinforced concrete with FEM]]
| Finite Element Analysis
| Reinforced concrete with FEM
| Intermediate
| Intermediate
| 1:00
| 1:00
Line 198: Line 225:
|-
|-
| [[Arch_panel_tutorial|Arch panel tutorial]]
| [[Arch_panel_tutorial|Arch panel tutorial]]
| Arch Workbench
| Modeling an architectural panel
| Beginner
| Beginner
| 1:00
| 1:00
Line 216: Line 243:
|-
|-
| [[Basic_Attachment_Tutorial|Basic Attachment Tutorial]]
| [[Basic_Attachment_Tutorial|Basic Attachment Tutorial]]
| Attachment
| Sketch attachment
| Beginner/intermediate
| Beginner/intermediate
| 1:00
| 1:00
Line 225: Line 252:
|-
|-
| [[Basic_modeling_tutorial|Basic modeling tutorial]]
| [[Basic_modeling_tutorial|Basic modeling tutorial]]
| Modelling
| Introduction to modelling
| Beginner
| Beginner
| 0:15
| 0:15
Line 243: Line 270:
|-
|-
| [[Basic_Sketcher_Tutorial|Basic Sketcher Tutorial]]
| [[Basic_Sketcher_Tutorial|Basic Sketcher Tutorial]]
| Sketcher
| Sketcher Workbench
| Beginner
| Beginner
| 1:00
| 1:00
Line 269: Line 296:


|-
|-
| [[Creating_a_simple_part_with_Part_WB|Creating a simple part with Part WB]]
| [[Creating_a_simple_part_with_Draft_and_Part_WB|Creating a simple part with Draft and Part WB]]
| Modeling
| Modeling
| Beginner
| Beginner
| 2:00
| 1:30
| Heda
| Heda
| -
| -
Line 278: Line 305:


|-
|-
| [[Creating_a_simple_part_with_Draft_and_Part_WB|Creating a simple part with Draft and Part WB]]
| [[Creating_a_simple_part_with_Part_WB|Creating a simple part with Part WB]]
| Modeling
| Modeling
| Beginner
| Beginner
| 1:30
| 2:00
| Heda
| Heda
| -
| -
Line 315: Line 342:
|-
|-
| [[Draft_tutorial|Draft tutorial]]
| [[Draft_tutorial|Draft tutorial]]
| Draft Workbench
| Drafting
| Beginner
| Beginner
| 0:30
| 0:30
Line 324: Line 351:
|-
|-
| [[Drawing_Template_HowTo|Drawing Template HowTo (obsolete)]]
| [[Drawing_Template_HowTo|Drawing Template HowTo (obsolete)]]
| Drawing Workbench
| 2D Drafting
| Intermediate
| Intermediate
| 1:00
| 1:00
Line 333: Line 360:
|-
|-
| [[Drawing_tutorial|Drawing tutorial (obsolete)]]
| [[Drawing_tutorial|Drawing tutorial (obsolete)]]
| Drawing Workbench
| Blueprints / Drawings
| Beginner
| Beginner
| 0:15
| 0:15
Line 342: Line 369:
|-
|-
| [[Dxf_Importer_Install|Dxf Importer Install]]
| [[Dxf_Importer_Install|Dxf Importer Install]]
| Import
|
| Intermediate
| Intermediate
| 0:05
| 0:05
Line 357: Line 384:
| 0.14.3700
| 0.14.3700
|
|

|-
| [[Example_Combined_Footing|Example Combined Footing]]
| Reinforcement Workbench
| Intermediate
|
| [[User:Shiv_Charan|Shiv Charan]]
| 0.20
| None

|-
| [[Example_Slab_Having_LShape_Rebars_Reinforcement_Mesh|Example Slab Having LShape Rebars Reinforcement Mesh]]
| Reinforcement Workbench
| Intermediate
|
| [[User:Shiv_Charan|Shiv Charan]]
| 0.20
| None

|-
| [[Example_Slab_Having_Mesh_Of_Straight_Rebars|Example Slab Having Mesh Of Straight Rebars]]
| Reinforcement Workbench
| Intermediate
|
| [[User:Shiv_Charan|Shiv Charan]]
| 0.20
| None

|-
| [[Example_Slab_Having_UShape_Rebars_Reinforcement_Mesh|Example Slab Having UShape Rebars Reinforcement Mesh]]
| Reinforcement Workbench
| Intermediate
|
| [[User:Shiv_Charan|Shiv Charan]]
| 0.20
| None

|-
| [[Example_Slab_Spanning_in_One_Direction|Example Slab Spanning in One Direction]]
| Reinforcement Workbench
| Intermediate
|
| [[User:Shiv_Charan|Shiv Charan]]
| 0.20
| None

|-
| [[Example_Slab_Spanning_in_Two_Directions|Example Slab Spanning in Two Directions]]
| Reinforcement Workbench
| Intermediate
|
| [[User:Shiv_Charan|Shiv Charan]]
| 0.20
| None


|-
|-
| [[Export_to_STL_or_OBJ|Export to STL or OBJ]]
| [[Export_to_STL_or_OBJ|Export to STL or OBJ]]
| Export to STL or OBJ
| Export
| Beginner
| Beginner
| 0:20
| 0:20
Line 384: Line 465:
| 0.16.6377 or above
| 0.16.6377 or above
|
|

|-
| [[FEM Example Capacitance Two Balls]]
| Finite Element Analysis
| Beginner
|
| [[User:Sudhanshu Dubey|Sudhanshu Dubey]]
| 0.19
| None


|-
|-
Line 400: Line 490:
| 0:10
| 0:10
| [[User:Drei|Drei]]
| [[User:Drei|Drei]]
| 0.16.6700 or above
| 0.17 or above
|
|


Line 450: Line 540:
|-
|-
| [[Import_from_STL_or_OBJ|Import from STL or OBJ]]
| [[Import_from_STL_or_OBJ|Import from STL or OBJ]]
| Import from STL or OBJ
| Import
| Beginner
| Beginner
| 0:30
| 0:30
Line 459: Line 549:
|-
|-
| [[Import_OpenSCAD_code|Import OpenSCAD code]]
| [[Import_OpenSCAD_code|Import OpenSCAD code]]
| Import OpenSCAD code
| Import
| Beginner
| Beginner
| 0:30
| 0:30
Line 468: Line 558:
|-
|-
| [[Import_text_and_geometry_from_Inkscape|Import text and geometry from Inkscape]]
| [[Import_text_and_geometry_from_Inkscape|Import text and geometry from Inkscape]]
| Import
| Import text and geometry from Inkscape
| Beginner
| Beginner
| 0:30
| 0:30
Line 495: Line 585:
|-
|-
| [[PartDesign_Bearingholder_Tutorial_I|PartDesign Bearingholder Tutorial I]]
| [[PartDesign_Bearingholder_Tutorial_I|PartDesign Bearingholder Tutorial I]]
| Product design - Bearingholder #1
| Product design
| Beginner
| Beginner
| 1:00
| 1:00
Line 504: Line 594:
|-
|-
| [[PartDesign_Bearingholder_Tutorial_II|PartDesign Bearingholder Tutorial II]]
| [[PartDesign_Bearingholder_Tutorial_II|PartDesign Bearingholder Tutorial II]]
| Product design - Bearingholder #2
| Product design
| Beginner
| Beginner
| 1:00
| 1:00
Line 513: Line 603:
|-
|-
| [[PartDesign_tutorial|PartDesign tutorial]]
| [[PartDesign_tutorial|PartDesign tutorial]]
| Sketcher
| Sketcher Workbench
| Beginner
| Beginner
| 0:15
| 0:15
Line 531: Line 621:
|-
|-
| [[Plot_Basic_tutorial|Plot Basic tutorial]]
| [[Plot_Basic_tutorial|Plot Basic tutorial]]
| Plot Workbench Basic Tutorial
| Plot Workbench
| Beginner
| Beginner
|
|
Line 549: Line 639:
|-
|-
| [[Post-Processing_of_FEM_Results_with_Paraview|Post-Processing of FEM Results with Paraview]]
| [[Post-Processing_of_FEM_Results_with_Paraview|Post-Processing of FEM Results with Paraview]]
| Finite Element Analysis
| Post-Processing of FEM Results with ParaView
| Intermediate
| Intermediate
| 2:00
| 2:00
Line 567: Line 657:
|-
|-
| [[Raytracing_tutorial|Raytracing tutorial]]
| [[Raytracing_tutorial|Raytracing tutorial]]
| Raytracing
| Raytracing Workbench
| Beginner
| Beginner
| 0:10
| 0:10
Line 594: Line 684:
|-
|-
| [[Scripted_Parts:_Ball_Bearing_-_Part_1|Scripted Parts: Ball Bearing - Part 1]]
| [[Scripted_Parts:_Ball_Bearing_-_Part_1|Scripted Parts: Ball Bearing - Part 1]]
| Python
| Part Scripting - Ball Bearing #1
| Beginner
| Beginner
| 0:30
| 0:30
Line 603: Line 693:
|-
|-
| [[Scripted_Parts:_Ball_Bearing_-_Part_2|Scripted Parts: Ball Bearing - Part 2]]
| [[Scripted_Parts:_Ball_Bearing_-_Part_2|Scripted Parts: Ball Bearing - Part 2]]
| Python
| Part Scripting - Ball Bearing #2
| Beginner
| Beginner
| 0:30
| 0:30
Line 612: Line 702:
|-
|-
| [[Scripts|Scripts]]
| [[Scripts|Scripts]]
| Python
| Scripting
| Beginner
| Beginner
|
|
Line 621: Line 711:
|-
|-
| [[Sketcher_Micro_Tutorial_-_Constraint_Practices|Sketcher Micro Tutorial - Constraint Practices]]
| [[Sketcher_Micro_Tutorial_-_Constraint_Practices|Sketcher Micro Tutorial - Constraint Practices]]
| Sketcher
| Sketcher Workbench
| Beginner
| Beginner
| 0:30
| 0:30
Line 639: Line 729:
|-
|-
| [[Sketcher_requirement_for_a_sketch|Sketcher requirement for a sketch]]
| [[Sketcher_requirement_for_a_sketch|Sketcher requirement for a sketch]]
| Sketcher
| Sketcher Workbench
| Beginner
| Beginner
|
|
Line 648: Line 738:
|-
|-
| [[Sketcher_Tutorial|Sketcher Tutorial]]
| [[Sketcher_Tutorial|Sketcher Tutorial]]
| Sketcher
| Sketcher Workbench
| Beginner
| Beginner
|
|
Line 654: Line 744:
|
|
|
|

|-
| [[TechDraw_HowTo_Page|TechDraw HowTo Page]]
| TechDraw Workbench
|
|
|
| 0.19
| None


|-
|-
Line 711: Line 810:
|-
|-
| [[Transient_FEM_analysis|Transient FEM analysis]]
| [[Transient_FEM_analysis|Transient FEM analysis]]
| Finite Element Analysis
| Transient FEM analysis
|
|
|
|
Line 720: Line 819:
|-
|-
| [[Tutorial_custom_placing_of_windows_and_doors|Tutorial custom placing of windows and doors]]
| [[Tutorial_custom_placing_of_windows_and_doors|Tutorial custom placing of windows and doors]]
| Arch Workbench
| Architecture
| Intermediate
| Intermediate
| 1:00
| 1:00
Line 729: Line 828:
|-
|-
| [[Tutorial_for_open_windows|Tutorial for open windows]]
| [[Tutorial_for_open_windows|Tutorial for open windows]]
| Arch Workbench
| Architecture
| Beginner
| Beginner
| 1:00
| 1:00
Line 747: Line 846:
|-
|-
| [[Tutorial_KinematicAssembly|Tutorial KinematicAssembly]]
| [[Tutorial_KinematicAssembly|Tutorial KinematicAssembly]]
| Assembly3
| Assembly3 Workbench
| Beginner
| Beginner
| 0:30
| 0:30
Line 761: Line 860:
| [[User:FBXL5|FBXL5]]
| [[User:FBXL5|FBXL5]]
| 0.20 or above
| 0.20 or above
| None

|-
| [[Tutorial KinematicSkeleton]]
| Assembly3 Workbench
| Level
| 0:40
| [[User:FBXL5|FBXL5]]
| 0.20
| None
| None


Line 792: Line 900:
|-
|-
| [[Wikihouse_porting_tutorial|Wikihouse porting tutorial]]
| [[Wikihouse_porting_tutorial|Wikihouse porting tutorial]]
| Import
| Wikihouse porting tutorial
| Intermediate/Advanced
| Intermediate/Advanced
| 1:00
| 1:00

Revision as of 09:19, 25 July 2022

이 페이지는 고품질 자습서를 제공합니다. 완전한, 정렬되지 않은 목록은 Category:Tutorials에 있습니다.

If you'd like to contribute with writing wiki documentation and tutorials, see the general wiki guidelines in WikiPages, and read the tutorial guidelines.

Please notice the version of FreeCAD used in the tutorial as some tutorials may use an old version of the program. Although the general modelling process may still work, some tools may have changed.

See also video tutorials.

Architecture and BIM

Modeling parts

FreeCAD provides two main workflows to modeling parts:

Please note that the PartDesign Workbench workflow was considerably changed from FreeCAD 0.17 onward; some of the tutorials haven't been updated and may refer to the 0.16 version.

The Raspberry Pi project has made simple tutorials that are easy to follow, particularly for those new to CAD systems:

Drafting and Sketching

Technical Drawings

FEM

CNC & 3D Printing

Rendering

Robot workbench

Development of the Robot Workbench is currently abandoned. Please inquire on our forum regarding any news or alternative workbenches.

Scripting

These are tutorials that are related to scripting or programming. They are geared towards more experienced users, who are already somewhat familiar with the program.

Tutorials - Comprehensive list

Here are listed all the tutorials that are not in the manual regardless of their quality. If a tutorial is listed in the Category:Tutorials and not in this table please insert it.

Tutorial Topic Level Time to complete hh:mm Authors FreeCAD version Example files


Add Button to FEM Toolbar Tutorial Finite Element Analysis JohnWang
Add FEM Constraint Tutorial Finite Element Analysis M42kus
Add FEM Equation Tutorial Finite Element Analysis JohnWang
Adding a new mouse navigation option to FreeCAD (unfinished) Programming Advanced Kunda1 0.19.x None
Advanced Attachment OYX Attachment Intermediate/Advanced drmacro 0.19 None
Advanced TechDraw Tutorial (unfinished) TechDraw Workbench Advanced domad 0.19 None
Aeroplane Part Workbench Beginner 0:10 Hughthecat
Analysis of reinforced concrete with FEM Finite Element Analysis Intermediate 1:00 HarryvL 0.19 or above
Arch panel tutorial Arch Workbench Beginner 1:00 Yorik
Arch tutorial Modeling Intermediate Yorik 0.14
Basic Attachment Tutorial Attachment Beginner/intermediate 1:00 Bance 0.17 and above Basic Attachment Tutorial.FCStd
Basic modeling tutorial Modelling Beginner 0:15 NormandC Any None
Basic Part Design Tutorial Modeling Beginner Mark Stephen (Quick61) and HarryGeier 0.17 or above Basic Part Design for v0.17
Basic Sketcher Tutorial Sketcher Workbench Beginner 1:00 Drei and Vocx 0.19 Basic Sketcher tutorial
Basic TechDraw Tutorial TechDraw Workbench Beginner WandererFan 0.17 and above Basic Part Design for v0.17 Sample Basic TechDraw Tutorial Sample
Code snippets Python Beginner
Creating a simple part with Draft and Part WB Modeling Beginner 1:30 Heda - -
Creating a simple part with Part WB Modeling Beginner 2:00 Heda - -
Creating a simple part with PartDesign Modeling Beginner 1:00 GlouGlou 0.17 or above Creating a simple PartDesign Body.FCStd
Customize Toolbars Beginner 0:05 Mario52 Any None
Draft ShapeString tutorial Product Design Beginner 0:30 r-frank and vocx 0.17 and above Draft_Shapestring_Text
Draft tutorial Draft Workbench Beginner 0:30 Drei and vocx 0.19 Draft tutorial updated
Drawing Template HowTo (obsolete) Drawing Workbench Intermediate 1:00 Mark Stephen (Quick61) 0.14.3700 or above None
Drawing tutorial (obsolete) Drawing Workbench Beginner 0:15 Drei 0.16 or above
Dxf Importer Install Import Intermediate 0:05 Mario52 Any None
Engine Block Tutorial Part Workbench Beginner 1:00 Andrewbuck40 0.14.3700
Example Combined Footing Reinforcement Workbench Intermediate Shiv Charan 0.20 None
Example Slab Having LShape Rebars Reinforcement Mesh Reinforcement Workbench Intermediate Shiv Charan 0.20 None
Example Slab Having Mesh Of Straight Rebars Reinforcement Workbench Intermediate Shiv Charan 0.20 None
Example Slab Having UShape Rebars Reinforcement Mesh Reinforcement Workbench Intermediate Shiv Charan 0.20 None
Example Slab Spanning in One Direction Reinforcement Workbench Intermediate Shiv Charan 0.20 None
Example Slab Spanning in Two Directions Reinforcement Workbench Intermediate Shiv Charan 0.20 None
Export to STL or OBJ Export Beginner 0:20 r-frank 0.16.6703
Extend FEM Module Finite Element Analysis M42kus
FEM CalculiX Cantilever 3D Finite Element Analysis Beginner 0:10 Bernd 0.16.6377 or above
FEM Example Capacitance Two Balls Finite Element Analysis Beginner Sudhanshu Dubey 0.19 None
FEM Shear of a Composite Block Finite Element Analysis Beginner/Intermediate 0:30 HarryvL 0.17.12960 or above
FEM tutorial Finite Element Analysis Beginner 0:10 Drei 0.17 or above
FEM Tutorial Python Finite Element Analysis Intermediate 0:30 Bernd 0.18.15985 or above
FreeCAD-Ship s60 tutorial Ship Workbench Beginner
FreeCAD-Ship s60 tutorial (II) Ship Workbench Beginner
How to install additional workbenches Programming Medium programmer 0:15 r-frank Any None
How to install macros Programming Medium programmer 0:15 Mario52 Any None
Import from STL or OBJ Import Beginner 0:30 r-frank 1.0 0.16.6703
Import OpenSCAD code Import Beginner 0:30 r-frank 0.16.6704 None
Import text and geometry from Inkscape Import Beginner 0:30 r-frank 0.16.6704
Import/Export IFC - compiling IfcOpenShell Arch Workbench Advanced 2:00 Pablo Gil
Measurement Of Angles On Holes TechDraw Workbench Beginner 0:01 AnHi 0.19
PartDesign Bearingholder Tutorial I Product design Beginner 1:00 NormandC
PartDesign Bearingholder Tutorial II Product design Beginner 1:00 NormandC
PartDesign tutorial Sketcher Workbench Beginner 0:15 Drei 0.16 or above
Path Walkthrough for the Impatient Path Workbench Chrisb
Plot Basic tutorial Plot Workbench Beginner
Plot MultiAxes tutorial Plot workbench Intermediate
Post-Processing of FEM Results with Paraview Finite Element Analysis Intermediate 2:00 HarryvL 0.19 Beam and wall
Python scripting tutorial Programming Intermediate
Raytracing tutorial Raytracing Workbench Beginner 0:10 Drei 0.16 or above
Robot 6-Axis Robot Workbench Intermediate
Robot tutorial Robot Workbench Beginner r-frank
Scripted Parts: Ball Bearing - Part 1 Python Beginner 0:30 r-frank 0.16.6706
Scripted Parts: Ball Bearing - Part 2 Python Beginner 0:30 r-frank 0.16.6706
Scripts Python Beginner onekk Carlo 0.19
Sketcher Micro Tutorial - Constraint Practices Sketcher Workbench Beginner 0:30 Mark Stephen (Quick61) and vocx 0.19 Sketcher Constraints practices
Sketcher reference
Sketcher requirement for a sketch Sketcher Workbench Beginner Maker None
Sketcher Tutorial Sketcher Workbench Beginner Ulrich
TechDraw HowTo Page TechDraw Workbench 0.19 None
TechDraw Pitch Circle Tutorial TechDraw Workbench Beginner 0:10 Andergrin 0.19 None
TechDraw TemplateGenerator TechDraw Workbench Intermediate FBXL5 0.19 None
TechDraw TemplateHowTo TechDraw Workbench Intermediate 1:00 wandererfan 0.17 None
Thread for Screw Tutorial Product design Advanced 1:00 DeepSOIC, Murdic, vocx 0.19 Updated: Thread for screw tutorial
Toothbrush Head Stand Modeling Beginner 1:00 EmmanuelG 0.16 or above Thingiverse 2403310
Topological data scripting Programming Intermediate
Transient FEM analysis Finite Element Analysis
Tutorial custom placing of windows and doors Arch Workbench Intermediate 1:00 Vocx 0.18 or above None
Tutorial for open windows Arch Workbench Beginner 1:00 Vocx 0.18 or above None
Tutorial FreeCAD POV ray Rendering Intermediate 2:00 Vocx 0.18 or above None
Tutorial KinematicAssembly Assembly3 Workbench Beginner 0:30 FBXL5 0.20 or above None
Tutorial KinematicController Programming Intermediate 1:00 FBXL5 0.20 or above None
Tutorial KinematicSkeleton Assembly3 Workbench Level 0:40 FBXL5 0.20 None
Tutorial Render with Blender Rendering Intermediate 1:00 Vocx 0.18 or above None
VRML Preparation for Robot Simulation Robot Workbench Intermediate 0.11.4252ppa1
Whiffle Ball tutorial Product design Beginner 0:30 r-frank and vocx 0.17 and above WhiffleBall_Tutorial_FCWiki.FCStd
Wikihouse porting tutorial Import Intermediate/Advanced 1:00