Translations:Arch Rebar/7/it: Difference between revisions

From FreeCAD Documentation
(Created page with "# Creare un elemento struttura # Passare nell'ambiente Sketcher # Selezionare una faccia dell'elemento strutturale # Premere il...")
 
No edit summary
Line 1: Line 1:
# Creare un elemento [[Arch Structure/it|struttura]]
# Creare un elemento {{Button|[[Image:Arch_Structure.svg|16px]] [[Arch Structure/it|Struttura]]}}.
# Passare nell'ambiente [[Sketcher Workbench/it|Sketcher]]
# Passare nell'ambiente [[Sketcher Workbench/it|Sketcher]].
# Selezionare una faccia dell'elemento strutturale
# Selezionare una faccia dell'elemento strutturale.
# Premere il pulsante {{KEY|[[Image:Sketcher NewSketch.png|16px]] [[Sketcher NewSketch/it|Crea uno sketch]]}} per iniziare un nuovo schizzo sulla faccia selezionata
# Premere il pulsante {{Button|[[Image:Sketcher NewSketch.svg|16px]] [[Sketcher NewSketch/it|Crea uno schizzo]]}} per iniziare un nuovo schizzo sulla faccia selezionata.
# Disegnare la sagoma dell'armatura
# Disegnare la sagoma dell'armatura.
# Premere il pulsante {{KEY|[[Image:Sketcher LeaveSketch.png|16px]] [[Sketcher LeaveSketch/it|Esci]]}} per terminare lo schizzo
# Premere il pulsante {{Button|[[Image:Sketcher LeaveSketch.svg|16px]] [[Sketcher LeaveSketch/it|Esci]]}} per terminare lo schizzo.
# Passare nel modulo [[Arch Workbench/it|Arch]]
# Passare nel modulo [[Arch Workbench/it|Arch]].
# Selezionare lo schizzo appena disegnato
# Selezionare lo schizzo appena disegnato.
# Premere il pulsante {{KEY|[[Image:Arch Rebar.png|16px]] [[Arch Rebar/it|Armatura]]}}, o i tasti {{KEY|R}} poi {{KEY|B}}
# Premere il pulsante {{Button|[[Image:Arch Rebar.svg|16px]] [[Arch Rebar/it|Armatura]]}}, o i tasti {{KEY|R}} poi {{KEY|B}}.
# Regolare le proprietà desiderate. Se qualcuna delle proprietà crea una situazione impossibile, l'armatura potrebbe non apparire immediatamente, ad esempio, se il diametro del tondino è 0, o se la lunghezza offset è maggiore della lunghezza dell'elemento struttura
# Regolare le proprietà desiderate. Se qualcuna delle proprietà crea una situazione impossibile, l'armatura potrebbe non apparire immediatamente, ad esempio, se il diametro del tondino è 0, o se la lunghezza offset è maggiore della lunghezza dell'elemento struttura.

Revision as of 16:44, 6 April 2019

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Arch Rebar)
# Switch to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]]
# Create an {{Button|[[Image:Arch_Structure.svg|16px]] [[Arch Structure|Arch Structure]]}} element.
# Switch to the [[Image:Workbench_Sketcher.svg|16px]] [[Sketcher Workbench|Sketcher Workbench]].
# Select one face of the structural element.
# Press the {{Button|[[Image:Sketcher NewSketch.svg|16px]] [[Sketcher NewSketch|New Sketch]]}} button to start a new sketch on the selected face.
# Draw the diagram of your bar.
# Press the {{Button|[[Image:Sketcher LeaveSketch.svg|16px]] [[Sketcher LeaveSketch|Leave Sketch]]}} button to finish.
# Switch back to the [[Image:Workbench_Arch.svg|16px]] [[Arch Workbench]].
# Select the sketch you just drew.
# Press the {{Button|[[Image:Arch Rebar.svg|16px]] [[Arch Rebar|Arch Rebar]]}} button, or press {{KEY|R}} then {{KEY|B}} keys.
# Adjust the desired properties (your rebar might not appear immediately, if some of the properties create an impossible situation, such as the bar diameter being 0, or the offset distances being bigger than the length of the structural element).
  1. Creare un elemento Struttura.
  2. Passare nell'ambiente Sketcher.
  3. Selezionare una faccia dell'elemento strutturale.
  4. Premere il pulsante Crea uno schizzo per iniziare un nuovo schizzo sulla faccia selezionata.
  5. Disegnare la sagoma dell'armatura.
  6. Premere il pulsante Esci per terminare lo schizzo.
  7. Passare nel modulo Arch.
  8. Selezionare lo schizzo appena disegnato.
  9. Premere il pulsante Armatura, o i tasti R poi B.
  10. Regolare le proprietà desiderate. Se qualcuna delle proprietà crea una situazione impossibile, l'armatura potrebbe non apparire immediatamente, ad esempio, se il diametro del tondino è 0, o se la lunghezza offset è maggiore della lunghezza dell'elemento struttura.