Sketcher CreateRectangle/ro: Difference between revisions

From FreeCAD Documentation
(Updating to match new version of source page)
(Updating to match new version of source page)
Line 22: Line 22:
Coordonatele indicatorului sunt afișate lângă indicator în culoarea albastră și în timp real.
Coordonatele indicatorului sunt afișate lângă indicator în culoarea albastră și în timp real.
</div>
</div>

To define a rectangle via a center point and an edge point, use the [[Sketcher_CreateRectangle_Center|Centered rectangle]] tool.


[[Image:SketcherCreateRectangleExample.png‎]]
[[Image:SketcherCreateRectangleExample.png‎]]
Line 30: Line 28:
<div class="mw-translate-fuzzy">
<div class="mw-translate-fuzzy">
== Cum se folosește ==
== Cum se folosește ==
</div>
</div>

See also: [[Sketcher_Workbench#Drawing_aids|Drawing aids]].

Pos-OVP = Positional [[Sketcher_Preferences#General|On-View-Parameters]]. {{Version|0.22}}<br>
Dim-OVP = Dimensional On-View-Parameters. {{Version|0.22}}


<div class="mw-translate-fuzzy">
<div class="mw-translate-fuzzy">
Line 36: Line 39:
* Apăsați tasta {{KEY|Esc}} sau click butonul drepta al mouse-ului pentru a abandona/anula această funcție.
* Apăsați tasta {{KEY|Esc}} sau click butonul drepta al mouse-ului pentru a abandona/anula această funcție.
</div>
</div>

==Notes==

* When launched the rectangle tools add a '''Rectangle parameters''' section at the top of the Sketcher [[Task_panel|Task panel]] ({{Version|0.22}}). It contains:
# A '''Mode''' spinbox to chose one of the modes to draw the rectangle:
#* Corner, length & width
#* Center, length & width
#* 3 corners
#* Center and two corners
# A '''Rounded corners''' checkbox to apply round corners to the rectangle.
# A '''Frame''' checkbox to add a contour with a constant offset to the (rounded) rectangle.
* All three buttons in this selection now launch the same tool but with different preset combinations of mode and options that can still be altered after the first click.
* If '''Rounded corners''' is enabled, the offset is inward, and the offset value is larger than the corner radius, the offset contour will be created without fillets.
* The modes '''3 corners''', and '''Center and two corners''' create parallelograms rather than rectangles.





Revision as of 09:30, 13 April 2024

Sketcher CreateRectangle

poziția meniului
Sketch → Sketcher geometries → Create rectangle
Ateliere
Sketcher
scurtătură
R
Prezentat în versiune
-
A se vedea, de asemenea,
Sketcher Polyline

Descriere

Desenează un dreptunghi definit prin două puncte diagonal opuse. Când pornește instrumentul, indicatorul mouse-ului se schimbă într-o cruce albă cu o iconițo cu un dreptunghi roșu. Coordonatele indicatorului sunt afișate lângă indicator în culoarea albastră și în timp real.

Cum se folosește

See also: Drawing aids.

Pos-OVP = Positional On-View-Parameters. introduced in version 0.22
Dim-OVP = Dimensional On-View-Parameters. introduced in version 0.22

  • Duă ce apăsați butonul 'Create Rectangle', click o dată pentru a defini primul colț, apoi glisăm mouse-ul și click a doua oară pentru a stabili al doilea unghi/colț.
  • Apăsați tasta Esc sau click butonul drepta al mouse-ului pentru a abandona/anula această funcție.